JAGUAR XFR 2010 1.G Workshop Manual

9.

























10. NOTE: Make sure the transmission fluid temperature
does not exceed 50 °C (122 °F). If the transmission fluid
temperature does exceed 50 °C (122 °F) stop the
transmission fluid level check and allow the transmission
fluid to cool until the temperature is below 30 °C (86 °F).

Allow the transmission fluid to drain from the transmission
fluid filler plug hole until the flow almost stops.


















NOTE: Install a new sealing washer.

Using the special tool, install the new transmission fluid fill
plug.

















11. CAUTION: Make sure the transmission fluid fill plug is
tightened to the correct specification. Failure to follow this
instruction may result in damage to the vehicle.

To make sure the transmission fill plug is torqued to
the correct specification. Using the special tool and
torque wrench the following calculation steps must be
followed.
Step 1. Multiply 35 Nm by the effective length of the
torque wrench (1).
Step 2. Add the effective length of the special tool (2)
to the effective length of the torque wrench (1).
Step 3. Divide the total of step 1 by the total of step 2.
Step 4. Set the torque wrench to the figure arrived at in
step 3.
Tighten the transmission fluid fill plug to the torque
given by the calculation.

12. Remove the special tool.

Installation).

15. Lower the vehicle.

16. Disconnect the Jaguar approved diagnostic equipment from the vehicle.
www.JagDocs.com

Published: 11-May-2011
Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Transmission Fluid Drain and Refill
General Procedures


WARNINGS:


Observe due care when draining, as the fluid can be very hot.
Observe due care when working near a hot exhaust system.

1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

2. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

3. Place a container under the transmission.


4. CAUTION: Discard the seal.
Special Tool(s): 307-452 307-452
Wrench, Transmission Filler Plug Special Tool(s)

5. CAUTION: Discard the component.
Allow the fluid to drain.














6. CAUTION: Make sure that a new component is
installed.

Torque: 8 Nm












7. NOTE: Use transmission fluid meeting Jaguar
specification.

Refill the transmission with fluid.

8. Allow the transmission fluid to drain from the transmission
fluid filler plug hole until the flow almost stops.
























9. NOTE: Install a new sealing washer.
Loosely install the transmission fluid fill plug.


















10. CAUTION: Make sure the transmission fluid fill plug is
tightened to the correct specification. Failure to follow this
instruction may result in damage to the vehicle.

To make sure the transmission fill plug is torqued to
the correct specification. Using the special tool and
torque wrench the following calculation steps must be
followed.
Step 1. Multiply 35 Nm by the effective length of the
torque wrench (1).
Step 2. Add the effective length of the special tool (2)
to the effective length of the torque wrench (1).
Step 3. Divide the total of step 1 by the total of step 2.
Step 4. Set the torque wrench to the figure arrived at in
step 3.
Tighten the transmission fluid fill plug to the torque
given by the calculation.

11. Carry out a transmission fluid level check.

Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, General Procedures).

Published: 11-May-2011
Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Input Shaft Seal
Removal and Installation

Special Tool(s)


100-012
Slide Hammer

100-012-01
Slide Hammer Adapter

307-613
Holding Pins, Torque Converter

308-246
Installer, Front Seal

308-375
Remover, Input and Output Seal Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle. www.JagDocs.com

3. Refer to: Transmission - TDV6 3.0L Diesel (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, Removal).







Installation

4. Special Tool(s): 307-613
























5. CAUTIONS:


Take extra care not to damage the edges of the
component.


Discard the seal.

Special Tool(s): 100-012, 100-012-01, 308-375

1. CAUTION: Install a new seal.

Special Tool(s): 308-246

3. CAUTION: Make sure the torque converter is fully
located into the oil pump drive.


























4. Refer to: Transmission - TDV6 3.0L Diesel (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L
Petrol, Installation).

5. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

100-012-01
Slide Hammer Adapter

204-264
Pinion Seal Replacer

205-053
Retainer, Drive Flange

303-D121
Puller, General Purpose

308-375
Remover, Input and Output Seal Removal

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and