JAGUAR XFR 2010 1.G Workshop Manual
Page 2251 of 3039
Published: 11-May-2011
Interior Trim and Ornamentation - Instrument Panel Speaker Grille
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. CAUTIONS:
Protect the surrounding trim to avoid damage.
Make sure that the clips are correctly located.
3.
4. CAUTION: Make sure that the component is correctly
located on the locating dowels.
NOTE: Do not disassemble further if the component is
removed for access only.
Torque: 2 Nm
Page 2252 of 3039
Page 2253 of 3039
Interior Trim and Ornamentation - Headliner
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. Refer to: Interior Rear View Mirror (501-09 Rear View Mirrors, Removal and Installation).
3. Refer to: Overhead Console (501-12 Instrument Panel and Console, Removal and Installation).
4.
Remove both sun visors.
Refer to: Sun Visor (501-05 Interior Trim and Ornamentation, Removal and Installation).
5.
Remove both A-pillar trim panels.
Refer to: A-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
6.
Remove both B-pillar upper trim panels.
Refer to: B-Pillar Upper Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
7.
Remove both C-pillar trim panels.
Refer to: C-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
8.
Remove both front seats.
Refer to: Front Seat (501-10 Seating, Removal and Installation).
9. Refer to: Rear Seat Cushion (501-10 Seating, Removal and Installation).
Page 2254 of 3039
www.JagDocs.com
Page 2255 of 3039
13.
Vehicles with roof opening panel
14. NOTES:
Note the different lengths of screws.
Make sure that the component is installed to the
position noted on removal.
Torque: 2 Nm
Page 2256 of 3039
Vehicles without roof opening panel
15. NOTES:
Note the different lengths of screws.
Make sure that the component is installed to the
position noted on removal.
Torque: 2 Nm
All vehicles
16.
Page 2257 of 3039
17.
18.
19.
WARNING: This step requires the aid of another
technician.
WARNING: This step requires the aid of another
technician.
CAUTIONS:
Note the fitted position of the component prior to
removal.
Make sure that these components are installed to the
noted removal position.
Page 2258 of 3039
Installation
20.
21.
CAUTION: Note the fitted position of the component
prior to removal.
NOTE: Make sure that the component is installed to
the position noted on removal.
WARNING: This step requires the aid of another
technician.
1. To install, reverse the removal procedure.
Page 2259 of 3039
Published: 11-May-2011
Interior Trim and Ornamentation - Loadspace Scuff Plate Trim Panel
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
1.
2.
Installation
1. To install, reverse the removal procedure. www.JagDocs.com
Page 2260 of 3039
Interior Trim and Ornamentation - Loadspace Trim Panel
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011
1.
2.
3.
Installation
Repeat the above procedure for the other side.
1. To install, reverse the removal procedure.