Torque bolt JAGUAR XFR 2010 1.G Service Manual

7. CAUTION: Make sure that the mating faces are clean and free of
foreign material.


NOTE: Install new lower timing cover.

Install the bolts, but do not tighten fully at this stage.

Special Tool(s): 303-1433

























8. NOTE: Tighten the bolts in the indicated sequence.
Torque:
M6 12 Nm M8 20 Nm








9. Remove the special tool.

10. Torque: 12 Nm

11.
12. Torque: 10 Nm
















Special Tool(s): 303-1442, 303-1443
















13. Remove the special tools.


14. NOTE: Tighten the bolts in the indicated sequence.

Torque: 11 Nm www.JagDocs.com

31.
32.
33. NOTES:


Install the bolt and unions finger tight before final tightening.


Remove and discard the blanking caps.

Torque:
Unions 21 Nm M6 11 Nm















Torque:
Unions 21 Nm















Torque:
M10 29 Nm M6 11 Nm

45.
46.
47.
48. Torque: 12 Nm


















CAUTION: Install all the bolts finger tight before final tightening.

Torque: 25 Nm

































CAUTION: Install all the bolts finger tight before final tightening.


NOTE: Tighten the bolts in the indicated sequence.

Torque: 48 Nm www.JagDocs.com

49. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.


Install the bolts in the noted position.

NOTES:


Make sure that the crankshaft is not rotated.


Make sure the crankshaft and flexplate mating faces are clean before
installation.


Tighten the retaining bolts working diagonally.

Torque:
Stage 1:45 Nm Stage 2:90°
50. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
51. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

52. Lower the vehicle.

53. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. NOTE: Tighten the bolts in the indicated sequence.

Torque: 12 Nm





















4. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm

7.
















8.
9.
10. NOTE: Tighten the bolts in the indicated sequence.

Torque: 12 Nm













Torque: 12 Nm
















Torque: 12 Nm
















Torque: 12 Nm

22.























23. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.


NOTE: Make sure to tighten the exhaust VVT unit
bolts first.
Torque: 32 Nm Special Tool(s): 303-1482
















Install the oil suction tube.
Torque: 10 Nm

26. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.

first. NOTE: Make sure to tighten the inlet VVT unit bolts
Torque: 32 Nm












27.
28.
Remove the special tool.

























Remove the special tool.

29.
30.
31.
Remove the special tool.
Special Tool(s): 303-1447















Install the special tool.
Special Tool(s): 303-1448
















CAUTION: Install the crankshaft pulley bolt with an
M16 washer to prevent damage to the crankshaft on
installation.
Torque: 50 Nm