LAND ROVER FRELANDER 2 2006 Repair Manual

Stage 1:Stage 2:
1. CAUTIONS:
Ext reme cl eanli ness must be exerci sed whenhandl ing t hese components .
Make s ure that new bolt s are ins t al led.
Inst all t he fl expl at e and t ight en the bol ts asi llus t rated.
T orque:45 Nm50°
1.
Inst all t he transmis si on and convert er.
Refer t o: Transmis s ion - I6 3.2L Pet rol (307-01 Automat icTrans mi ss ion/Transaxle, Removal).
2.
Connect t he batt ery ground cable and ins tall t he cover.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
3.

P ubl ished: 23-Aug-2011
Engine - I6 3.2L Petrol - Crankshaft Main Bearing Carrier
Re moval and Inst a llat ion
Spe cia l T ool(s) 303-1219
Locking Tool, Cra nks ha ft 303-1278
Aligner, Timing Cove r 303-1280
Remover, Oil P ump Pi n 303-1284
Torx Socket , Acces sory Drive P ulle y
Removal
• NOTE: Re moval st eps in t his procedure may cont ai n inst all at ion det a ils.
• NOTE: Some variat ion in t he illust ra ti ons ma y occur, but t he e ss enti al informat ion is a lways corre ct .
1. W ARNING: Do not work on or under a ve hicle s upport e d only by a jack.
Always s upport t he ve hicle on s afet y st ands .
Rais e a nd s upport t he ve hicle.
1. 2. W ARNING: Avoi d skin cont act wit h t he s pe ci fied mat e rial.
• CAUTIONS: Hot flui d.
Be pre pa red t o collect es ca ping fluids .
T orque : 38 Nm Re move a nd dis ca rd t he sea ling was her.2.
Refe r t o: Engine (303-01A Engi ne - I6 3.2L Pet rol, Removal).
3.

4.
Spec ial T ool(s ):
303-1284 ,
303-1278 T orque :
60 Nm 5.
T orque :
65 Nm 6.
7.
NOTE: This s t ep re qui res t he ai d of a not her t echnici an.
T orque : 65 Nm 7.

8.
NOTE: Some varia t ion in t he illust rat ions may occur, but t he e ss ent ia l
inf orma t ion is a lways correct .
If t he locking pin on t he s pe cia l t ool is dis engage d, t he
cranks haft can be rota t ed.
Spec ial T ool(s ): 303-1219 8.
T orque :
10 Nm 9.
T orque :
47 Nm 10.
T orque :
10 Nm 11.

12. CAUTION: Ma ke sure t hat t he t orque convert e r remains in t he
t ransmiss ion.
• NOTE: This s t ep re quires the a id of a nother t echnician.
T orque : 47 Nm 12.
Mount the engine t o a n engine st a nd.
13. T orque :
10 Nm 14.
T orque :
10 Nm 15.

T orque :
48 Nm 16.
17.
T orque :
10 Nm 18.
T orque :
10 Nm 19.

20.
NOTE: Some vari at ion in t he illust ra ti ons ma y occur, but t he
es se nt ial informat ion is alwa ys correct .
20. 21.
NOTE: Make s ure t hat all t ra ce s of t he old s eal ant are removed from
t he mat ing fa ce s.
T orque : M7 17 Nm M10
45 Nm 21.
22. CAUTION: Discard the s eal .
T orque : 17 Nm 22.
Vehicles built up to VIN:148530 23. CAUTION: Discard the s eal s.
T orque : 17 Nm 23.
All vehicles

24. CAUTION: Discard the s eal s.
T orque : 17 Nm 24.

Re move t he oi l pump pivot pin.
Spec ial T ool(s ): 303-1280 25.
26.

27.
28.
Installation
1.

St a ge
1:
St a ge
2: 2.
CAUTION: Ma ke
s ure t hat t he
mat ing faces are
clea n and free of
fore ign ma te rial .
Apply a
2.5mm
bead of
s eal ant
STC50550
(Locti t e
5900) to
t he are as
s hown.2.
3.
CAUTION:
Ti ght e n
t he bol ts
in the
s equence
s hown.
T orque :
5 Nm 30 Nm3.