MAZDA PROTEGE 1992 Workshop Manual

ASSEMBLY Bl
03UOBl-16
03UOB1.21 38
Injector and Distribution Pipe Assembly (BP SOHC)
1. Install the injector and distribution pipe assembly with new
insulators.
Tightening torque:
19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
Intake Manifold Assembly
1, Remove all foreign material from the intake manifold con-
tact surface.
2. Install a new gasket and the intake manifold assembly.
Tightening torque:
19-25 N*m (1.9-2.6 m-kg, 14-19 ft-lb)
Distributor and High-tension Lead
1. Apply engine oil to the O-ring, and position it on the dis-
tributor.
2. Apply engine oil to the blade.
3. Install the distributor with the blade fit into the camshaft
groove.
4. Temporarily, loosely tighten the distributor installing bolt.
5. Adjust the ignition timing after engine installation.
(Refer to Section G.)
6. Connect the high-tension leads.
81-91

Bl ENGINE STAND DISMOUNTING
ENGINE STAND DISMOUNTING
PROCEDURE
1. Remove the engine from the SST (engine stand).
2.
Remove the SST (engine hanger) from the engine.
3. Install the parts shown in the figure.
Torque Specifications
19-25 11.9-2.6. 14-191
(3.8-5.3, 27-38)
52 (3.8-5.3, 27-38)
7.0111 N-m
(80-110 cm-kg, 69-95 in-lb)
T- :p,;f W-23 (1.6-2.3, 12-17)
19-25 (1.9-2.6, 14-19)
N-m (m-kg, Mb)
OWOBX-25‘
Water Inlet Pipe
1. Remove all foreign material from the water inlet pipe mount-
ing surface.
2. Install a new gasket and the water inlet pipe.
Tightening torque:
19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
-,
03UOBl-169
81-92

ENGINE STAND DISMOUNTING Bl
VIEW A
c==A
03UOBi -17
I
03UOBi-2C
05UOBX-25
03UOBl-171
OWOBX-25
3. Apply a small amount of engine coolant to the new O-ring.
4. Install the water bypass pipe.
Exhaust Pipe Bracket
1. Install the exhaust pipe bracket.
Tightening torque:
37-52 N*m (3.8-5.3 m-kg, 27-38 ft-lb)
A/C Compressor Bracket
1. Install the A/C compressor bracket.
Tightening torque
@: 19-25 N-m (1.9-2.8 m-kg, 14-19 ft-lb)
@I: 37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
Exhaust Manifold
1. Remove all foreign material from the exhaust manifold con-
tact surface.
2. Install a new gasket and the exhaust manifold.
Tightening torque:
18-23 N-m (1.8-2.3 m-kg, 12-17 ft-lb)
Exhaust Manifold Insulator
1. Install the exhaust manifold insulator.
Tightening torque:
7.8-l 1 N*m (80-l 10 cm-kg, 89-95 in-lb)
Bl-93

81 INSTALLATION
INSTALLATION
PROCEDURE
Tighten all bolts and nuts to the specified torques.
Step 1
Join the engine and transmission,
Torque Specifications
MTX
BP SOHC
19-25 (1.9-2.8, 14-19)
W
y
37-52 (3.8-5.3, 27-38)
37-52 (3.8-5.3, 27-38)
84-89 (6.5-9.1, 47-66)
ATX
BP SOHC
19-2ii (1.9-2.8, 14-19)
An
I
y 37-52 /
b ‘i
--< ($8-5.3, 27-36)
34-49
(3.5-S
37-52 (3.8-5.3, 27-38)
Bl--94
S--i0 (5.6-8.2, 41-59)
N.m (m-kg, R-lb)
23UOBl-0%

INSTALLATION Bl
Step 2
Warning
l Be sure the vehicle is securely supported on safety stands.
Taraue Soecifications
'S-80 (5.6-6.2, 41-59) 74-103 (7.5-10.5, 54-76)
h // 67-93 43-61
(6.8-9.5, 49-69) (4.4-6.2, 32- .45)
64-89 (6.5-9.1, 47-66)'
'
/cR-x&l /84-89 (6.5-9.1, 47-66)
>\----37-L5i (3.8-5.3.
27-38)
N.m (m-kg, ft-II
0311081-i
Ii------ //Ill 1 Engine mount member
1. Install the engine mount member.
Tightening torque:
64-69 N#m (6.5-9.1 m-kg, 47-66 f&lb)
Bl-95

INSTALLATION
03UOBl-17
No.2 ENGINE /I Ill
03UOBl-171
DYNAMIC DAMPER
03UOBl-17;
03UOBl-178
ATX
1 03UOBl.179
91-96
Engine and transaxle assembly
1. Suspend the engine and transaxle assembly.
Caution
l Do not damage any components in the engine com-
partment.
2. Align the No.1 and No.2 engine mount bolts with the en-
gine mount member mounting holes.
Engine mount
1. Install the No.1 engine mount nut and tighten.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 f&lb)
2. Install the No.2 engine mount nut and tighten.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
3. Install the engine mount rubber with new washer and tight-
en nut @.
Tightening torque:
74-103 N.m (7.5-10.5 m-kg, 54-76 ft-lb)
4. Install the bolt @, while aligning the engine location and
tighten nut (I!$.
Tightening torque:
67-93 N-m (6.8-9.5 m-kg, 49-69 ft-lb)
5. Install the dynamic damper.
Tightening torque:
55-80 N.m (5.6-8.2 m-kg, 41-59 ft-lb)
6. Install the No.4 engine mount rubber and bracket and loose-
ly tighten nuts @.
7. Align the bracket bolt holes with the body side holes, and
install the bolt @and tighten in the sequence shown in the
figure.
Tightening torque:
43-61 N-m (4.4-6.2 m-kg, 32-45 f&lb)
8. Tighten the nuts @.
Tightening torque: 67-93 N.m (6.6-9.5 m-kg, 49-69 ft-lb)

Step 3
Torque Specifications
INSTALLATION
ATX
Bl
6.9-11 N-m
(70-110 cm-kg, 61-95 in-lb)
GAs~~~~~~~~c~~~,~
(3.2-4.7, 23-34) 16-23 6.9-9.6 N.m
11.6-2.3. 12-17) (70-100 cm-kg, (4.3-5.6, 31-42) -43)
NEW \.~ 61-67 in-lb)
N.m (m-ka. R-lb
Driveshaft
1. Apply grease to the end of the driveshaft.
Caution
l When installing the driveshaft, be careful not to
damage the oil seal.
l After installation, pull the front hub outward to con-
firm that the driveshaft is securely held by the clip.
2. Install the driveshaft and a new clip.
3. Install the lower arm ball-joint to the knuckle; then tighten
the locknut.
Tightening torque:
43-59 N,rn (4.4-6.0 m-kg, 32-43 f&lb)
Bl-97

Bl INSTALLATION
Tie-rod end
1. Install the tie-rod end to the knuckle.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
2. Install the new split pin.
03UOBl.183
,I / 03UOBl-18
Stabilizer
1. Install and adjust the stabilizer.
Dimension @: 17-19mm (0.67-0.75 in)
Extension bar (MTX)
1. Install the extension bar to the transaxle.
Tightening torque:
31-46 N-m (3.2-4.7 m-kg, 23-34 ft-lb)
Shift control rod (MTX)
1. Install the shift control rod to the transaxle.
Tightening torque:
16-23 N.m (I .6-2.3 m-kg, 12-l 7 ft-lb)
Clutch release cylinder (MTX)
1. Install the clutch release cylinder.
Tightening torque:
16-23 N#m (I .6-2.3 m-kg, 12-17 ft-lb)
2. Set the pipe bracket in position.
Tightening torque
@: 6.9-9.8 N.m (70-100 cm-kg, 61-87 in-lb)
@: 16-23 N.m (I .6-2.3 m-kg, 12-17 ft-lb)
Shift control cable (ATX)
1. Install the shift control cable to the transaxle.
Tightening torque:
6.9-l I N-m (70-l IO cm-kg, 61-95 in-lb)
81-98

INSTALLkTlON Bl
03UOBl-188
03UOBl-18
Step 4
1. Connect the hoses shown in the figure.
Caution Speedometer cable
1. Install the speedometer cable.
Tightening torque:
7.8-l 1 Nom (80-l 10 cm-kg, 69-95 in-lb)
Exhaust pipe
1. Install the exhaust pipe and a gasket; then loosely tighten
the locknuts.
2. Loosely tighten the bracket bolts.
3. Tighten the locknuts.
Tightening torque:
31-46 N-m (3.2-4.7 m-kg, 23-34 ft-lb)
4. Tighten the bracket bolts.
Tightening torque:
37-52 Nmrn (3.8-5.3 m-kg, 27-38 ft-lb)
l Position the hose clamp in the original location on the hose, and squeeze the clamp lightly
with large pliers to ensure a good-fit.
BP SOHC
03UOBl-1s
Bl-9

Bl INSTALLATION
Step 5
1. Connect the harness connectors shown in the figure.
GROUND ALTERNATOR
OIL PRESSURE SWITCH
I- THFOTTLE SENSOR
NEUTRAL SWITCH (MTX)
IGNITION COIL
$A_c_K;u_p LIGHT SWITCH
____------- ;
Step 6
Torque Specifications
7.8-11 N.m (80-110 cm-kg, 89-95 in-lb)
19-25 (1.9-2.6, 14-19)
2.9-5.9 N.m
(30-60 cm-kg, 26-52 in-lb)
7.8-11 N.m
(80-l 10 cm-kg,
6.4-9.3 N.m 37-52
(3.8-5.3, 27-38)
24-35
(2.4-3.6, 17-26)
7.8-11 N.m 160-110 cmika, 69-95 in-lb) ‘-- -- -..’ ‘-=’ -’ / 166-96 r?m.ka.
66-82 in-lb) 69-95 in-lb)
N.m (m-kg, ft-lb -- OBUOBl-1E
Bl-100