belt MAZDA PROTEGE 1992 Repair Manual

ON-VEHICLE MAINTENANCE B2
- 05UOBX-04:
---_____~
OWOBX 04
----
05UOBX-03
4
2. Loosen the tensioner lock bolt.
Caution
l To prevent damage to the tensioner, secure it with
a rag.
3. Temporarily secure the tensioner with the spring fully ex-
tended.
Caution
Q Do not allow any oil or grease on the timing belt.
4. Remove the timing belt and secure it out of the way to pre-
vent damage during removal and installation of the cylin-
der head.
Cylinder head bolt
1. Loosen the cylinder head bolts in two or three steps in the
order shown in the figure.
2. Remove the cylinder head bolts.
Installation note
Cylinder head bolt
1. Apply clean engine oil to the bolt threads and seat faces.
2. Install the cylinder head bolts.
3. Tighten the cylinder head bolts in two or three steps in the
order shown in the figure.
Tightening torque:
76-81 N-m (7.7-8.3 m-kg, 56-60 ft-lb)
Cylinder head cover
1, Apply silicone sealant to the shaded areas as shown in the
figure.
2. Install the cylinder head cover.
Tightening torque:
4.9-8.8 N-m (50-90 cm-kg, 43-78 in-lb)
B2-19

B2 ON-VEHICLE MAINTENANCE
03UOB2-033
FOUR TEETH
13UOB2-015
05UOBX-032
B2-20
Timing belt
1. Check that the ignition timing mark (yellow) on the crank-
shaft pulley and the timing mark on the timing belt cover
are aligned.
2. Verify that the camshaft pulley marks are aligned with the
seal plate marks.
Caution
l For intake side, align the I mark.
l For exhaust side, align the E mark.
3. Install the timing belt so that there is no looseness at the
idler side or between the two camshaft pulleys.
Caution
l Do not turn the crankshaft counterclockwise.
4. Turn the crankshaft two turns clockwise, and align the tim-
ing belt pulley mark with the timing mark.
5. Verify that the camshaft pulley marks are aligned with the
seal plate marks.
If not aligned, remove the timing belt and repeat from ten-
sioner installation.
6. Turn the crankshaft 1 and 5/6 turns clockwise, and align
the fourth tooth from the
I mark with the seal plate mark.
7. Loosen the tensioner lock bolt to apply tension to the tim-
ing belt.
8. Tighten the tensioner lock bolt.
Tightening torque:
37-52 N#rn (3.8-5.3 m-kg, 27-38 ft-lb)
9. Turn the crankshaft 2 and l/6 turns clockwise and verify
that the timing marks are correctly aligned.

ON-VEHICLE MAINTENANCE
DEFLECTION CHECKING POINT
05UOBX-03 3 10. Measure the timing belt deflection by applying moderate
pressure (98 N, 10 kg, 22 lb) midway between the two cam-
shaft pulleys.
If the deflection is not correct, repeat from Step 7 above.
Deflection:
9.0-11.5mm (0.35-0.45 in) at 98 N (10 kg, 22 lb)
Harness
1. Connect the harness connectors. (Refer to page 82-l 8.)
Hose
1. Connect the hoses. (Refer to page 82-17.)
03UOB2-035
Accelerator cable
1. Install the accelerator cable.
2. Check the accelerator cable deflection.
If the deflection is not correct, adjust by turning nut A.
Deflection: l-3mm (0.04-0.12 In)
Steps After Installation
1. Fill the radiator with the specified amount and type of engine coolant. (Refer to Section E.)
2. Connect the negative battery cable.
3. Start the engine and check as follows:
(1) Engine oil and engine coolant leakage.
(2) Ignition timing, idle speed. (Refer to page B2-8.)
(3) Operation of emission control system.
4. Recheck the engine coolant levels.
2311082-022
B2-21

B2 ON-VEHICLE MAINTENANCE
HLA
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note --- ----- -__ __-- ,‘.
11.3-14.2 N.m
(1.15-1.45 m-\g, 100-126 in-lb)
49-61
(5.0~6.2,-36-45)
4.9-6.6 N.m
(50-90 cm-kg, 43-76 in-lb)
7.6All N-m
(80-110 cm-kg, 69-95 in-lb) 1 Q’-25
(1.9-2.6, 14-19)
N.m (m-kg, ft-lb)
0311082-03
1. High-tension lead
10. Cylinder head cover
2. Distributor
Installation Note..
....................
Installation Note.. ......................
page 62-25
11. Camshaft pulley
3. P/S and/or A/C drive belt
Removal note ..........................
Removal / Installation..
.............. page E32-
6
Installation Note .......................
4. Alternator drive belt
12. Seal plate
Removal / Installation
......... . ...... page B2- 6
13. Camshaft
5. Water pump pulley
Removal Note.. ........................
6. Timing belt cover, upper
Installation Note.. .....................
7. Timing belt cover, middle
14. HLA
8. Spark plug
Removal note ..........................
9. Timing belt
Installation
Note.. .....................
Removal Note.. .........................
page B2-18 Inspection
................................
Installation Note.. ......................
page B2-20
7
page 62-19
page 82-23
page 82-24
page B2-23
page 62-23
page B2-23
page B2-23 ‘--’
page 82-60
82-22

B2 ON-VEHICLE MAINTENANCE
FRONT OIL SEAL
Replacement
1. Disconnect the negative battery cable.
2. Raise the vehicle on a lift and remove the right front wheel.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal, referring to Installation Note.
I

@Em
157-167 (16-17, 116-123)
N.m (m-kg, ft-lb
1. Timing belt related parts.. ............ page B2-12
2. Pulley lock bolt
Removal Note ..................................... below
Installation Note.. page B2-27 ......................
3. Pulley boss
4. Timing belt
Removal Note.. ......................... page B2-13
Installation Note ........................ page B2-14 5. Timing belt pulley
Installation Note..
...................... page B2-27
6. Oil seal
Removal Note.. ......................... page B2-27
Installation Note.. ...................... page B2-27
Removal Note
Pulley lock bolt
1. Hold the pulley boss with the SST.
2. Loosen and remove the pulley lock bolt.

ON-VEHICLE MAINTENANCE
I 05UOBX-063
Oil seal
1. Cut the oil seal lip with a razor knife.
2. Remove the oil seal with a screwdriver protected with a rag.
13EOB2-02
ALIGN.KEY GRCi&E
13EOB2-02
23UOB2-025
Steps After Installation
1. Connect the negative battery cable.
2. Start the engine and check as follows:
l Ignition timing. (Refer to page 92-8.)
3
Installation Note
Oil seal
1. Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
3. Tap the oil seal in evenly with a suitable pipe and a ham-
mer until it is about flush with the face of the oil pump body.
Oil seal outer diameter: 50.5mm (1.98 in)
Timing belt pulley
1. Install the timing belt pulley.
2. Install the pulley Woodruff key with the tapered side toward
the oil pump body.
Pulley lock bolt
1. Hold the crankshaft with the SST and tighten the pulley lock
bolt.
Tightening torque:
157-187 N.m (18-17 m-kg, 116-123 ft-lb)
23UOB2-026
82-27

REMOVAL
REMOVAL
Warning
l Release the fuel pressure. (Refer to Section F.)
PROCEDURE
1. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil,.
3. Remove in the order shown in the figure, referring to
Removal Note.
Step
1
1. Undercover and side cover 12. Oil cooler hose (ATX)
2. Resonance chamber 13. Cooling fan connector
3. Air cleaner assembly 14. Radiator switch connector (ATX)
4. Battery bracket 15. Radiator bracket
5. Battery cover 16. Radiator and cooling fan assembly
6. Battery
17. P/S and/or A/C drive belt
7. Battery carrier Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2- 6
8. Battery duct 18. P/S oil pump and bracket
9. Accelerator cable Removal Note . . . . . . . . . . . . . . . . . . . . + . . . . . . page 82-32
10. Radiator hose 19. A/C compressor (if equipped)
11. Coolant reservoir hose Removal Note.. . . . . . . . . . . . . . . . . . . . . . . . . . page 82-32
B2-31

B2 DISASSEMBLY
AUXILIARY PARTS
1, Drain the engine oil.
2. Disassemble in the order shown in the figure
GASKET, REPLACE ..______-.
-___ -
03UOB2-064
1. Distributor and high-tension lead 7. Oil cooler
2. Intake manifold assembly 8. Oil pressure switch
3. Injector and distribution pipe assembly 9. Spark plug
4. Alternator and drive belt 10. Oil level gauge
5. No.3 engine mount bracket 11. Oil level gauge pipe stay
6. Oil filter 12. Engine hanger
82-42

DISASSEMBLY 82
TIMING BELT
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
23UOB2-0:
1. Water pump pulley
2. Crankshaft pulley
3. Timing belt cover, upper
4. Timing belt cover, middle
5. Timing belt cover, lower
6. Pulley lock bolt
7. Pulley boss
8. Timing belt
Disassembly Note . . . . . . . . . . . . . . . . . . . . page B2-44
9. Tensioner and tensioner spring
10. Idler
Disassembly Note . . . . . . . . . . . . . . . . . . . . page B2-44
B2-43

B2 DISASSEMBLY
23UOB2-055
13EOB2-030
Disassembly Note
Pulley lock bolt
1. Hold the flywheel (MTX) or drive plate (ATX) with the SST
or equivalent.
2. Loosen the pulley lock bolt.
3. Remove the pulley lock bolt.
Timing belt
1. Loosen the tensioner lock bolt and using a suitable bar, pry
the tensioner outward.
Caution
l Protect the tensioner with a rag before prying.
2. Tighten the lock bolt with the tensioner spring fully extended.
Note
l Mark the timing belt rotation for proper reinstal-
lation.
3. Remove the timing belt.
82-44