MITSUBISHI SPYDER 1990 Service Repair Manual

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE>
REMOVAL AND INSTALLATION
Be not subject the any shocks
trol cable and shift lever assembly.
Engine>
8.8 Nm6.5
11 Nm
11 Nm8.3
118.3l
N m . .
NOTE Resin clip position11 Nm
8.3
Transaxle control cable assemblyremoval steps
1. Air cleaner and air intake hose sembly
2. Center panel
3. Cup holder assembly
4. Floor console assembly 5. Console side cover (L.H.)
6. Console side cover
(R.H.)
7. TCM bracket
8. Transaxle control module (TCM)
9. Nut10. Clip 11. Clip
12. Transaxle control cable connection
13. Nut14. Transaxle control cable assembly Selector lever assembly removal
steps
2. Center panel
3. Cup holder assembly
4. Floor console assembly 5. Console side cover (L.H.)
6. Console side cover (R.H.)
11. Clip
12. Transaxle control cable connection
15. Snap pin
16. Key interlock cable connection
17.
lock cable connection
18. Overdrive switch/position indicator
light connector19. Selector lever assembly
TSB Revision

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE> Transaxle
I N S T A L L A T I O N S E R V I C E P O I N T
(1) Put the selector lever in the posit/on.
(2) Loosen the adjusting nut, gently pull the transaxle control
cable in the direction of the arrow tighten nut.
TSB Revision

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND
SELECTOR LEVER ASSEMBLY
DISASSEMBLY AND REASSEMBLY
arrow-located places)
Disassembly steps
11 Nm8.3
1. Overdrive switch position indicator12. Position indicator light assembly
light connector case
2.Cover
3. Selector knob4. Overdrive switch button5. Overdrive switch6.Pin
13.Sleeve
14.Bolt15.Lever assembly
16. Detent spring assembly17.Bushing18.Pipe19.Cotter pin20.Washer21.Lock cam22.Bracket assembly
91.5
2Nm
7. Push button8. Spring9. Indicator panel upper10. Slider11. Indicator panel lower
Terminal
Flat-tip screw driver
TSB Revision
DISASSEMBLY SERVICE POINTS
OVERDRIVE SWITCH POSITION INDICATOR
LIGHT CONNECTOR CASE REMOVAL
Use a flat-tip screwdriver or similar tool to pull out the terminal
from the overdrive switch/position indicator light connector
case.

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE> Transaxle Control
-ever
te
SleeveDetent plate
Selector lever
Detent pin
TSB Revision
OVERDRIVE SWITCH BUTTON/OVERDRIVE
SWITCH REMOVAL
(1) Use a flat-tip screwdriver to remove the overdr ive switch
button.
(2) Remove the overdrive switch mounting screw.
(3) Pressing the switch, remove the overdrive switch.
REASSEMBLY SERVICE POINTS
DE T E N TS P R I NG A S S E M BLY
Shift the selector lever to the neutral (N) positio n, and then
install the detent spring assembly so that the roll er is in the
detent plate groove.
SELECTOR KNOB INSTALLATION
(1) Put the selector lever in the position, turn the sleeve
and adjust the dimension between the sleeve and the
end of the lever so it reaches 16 mm (1.02 in.)
(2) Install the selector knob.
(3) Check that dimension (A) between the detent pla te and
detent pin reaches the standard value.
Standard value (A): 1.7-2.4 mm
in.)
(4) If outside the standard value, remove the selec tor knob
and turn the sleeve again to readjust.

,
(TURBO) AND ENGINE> . .
.
lCheck the wear
lCheck the spring’ for
OVERDRIVE SWITCH CONTINUITY
Terminal No.Switch position3
OD is operating (ON)
OD is not operating (OFF)
TSB Revision

AUTOMATIC TRANSAXLE Automatic Transaxle Key Interlock
ENGINE (TURBO) AND ENGINE> and Shift Lock Mechanisms
23200120045
REMOVAL AND INSTALLATION
Caution:Be careful not to subject the SRS-ECU to any shocksduring removal and installation of the key interlockcable and shift lock cable.
567
I
- -
1 8 ’
NOTE(1) clip
(2) clipposition position
Key interlock cable removal steps
1. Plug A
2. Plug
3. Hood release lever
4. Instrument panel under cover
5. Steering column lower cover
6. Center panel7. Cup holder assembly
8. Floor console assembly9. Console side cover (L.H.)
10. Cover Cam and lever
12. Key interlock cable connection
13. Slide lever
14. Snap pin
15. Key interlock cable connection 19. Key interlock cable
11 Nm
8.30 0 0 0 3 9 3 3
Shift lock cable removal steps 1. Plug A
2. Plug
3. Hood release lever
4. Instrument panel under cover
6. Center panel
7. Cup holder assembly
8. Floor console assembly
9. Console side cover (L.H.)
16. Shift lock cable connection
17. Cotter pin
18. Shift lock cable connection
20. Shift lock cable
TSB Revision

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE> Lock
LOCK
I N S T A L L A T I O N
Secure the section between the metals of the
and key interlock cable with the of the steering cover
assembly.
Caution ,
Do not change the routing of shift lock cable to the
lever assembly. .
LOCK CABLE (SELECTOR LEVER SIDE)
INSTALLATION
(1) Place the selector fever in position
(2) Fasten the shift lock cable’ at the position where the end
of the shift lock cable is
above the red marking.
LEVER
I N S T A L L A T I O N
(1) Install the key interlock cable on the lock cam .
(2) Install the spring and washer of the key interl ock cable
as shown.
(3) While lightly pushing the cable coupling portio n of the
cam in-the direction A, tighten the nut to fasten the
key interlock cable. .
Check the cable assemblies for function and for dam
age.
TSB Revision

AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE> Transaxle Assembly
23100570192
REMOVAL AND INSTALLATION
Engine (Turbo)>
(Refer to GROUP 00 Maintenance
(Refer to GROUP 42 Under Cover.)
Post-installation Operationl Battery Installationl Under Cover Installation(Refer to GROUP 42 Under Cover.)l Transaxle Fluid Supplying(Refer to GROUP 00 Maintenance Service.)l Selector Lever Operation Check
Removal steps
1. Air cleaner cover and air intakehose assembly2. Air cleaner element
3. Air hose
4. Air hose A5. Battery tray
6. Evaporative emission canister
7. Evaporative emission canister holder
8. Battery tray stay
9. Transaxle control cable connection
10. Oil dipstick and guide assembly Starter motor
12. Park/Neutral position switch con-
nector
13. Oil temperature sensor connector
14. Kick down servo switch connector
15. Solenoid valve connector
16. Pulse generator connector
17. Speedometer connector
18. Transaxle assembly mounting bolts
19.
roll stopper bracket mounting
20. Transaxle mounting bracket mount-
ing nuts21. Transaxle oil cooler hoses connectionl Supporting engine assembly
TSB Revision

AUTOMATIC TRANSAXLE , . . ,
ENGINE (TURBO) AND ENGINE> Transaxle Assembly
33
45-52Nm
33-38
2 5
From under vehicles
22. Tie rod end ball joint and knuckle
connection23. Stabilizer link connection
24. Damper fork
25. Lateral lower arm ball joint and
knuckle connection26. Compression lower arm ball jointand knuckle connection 27. Drive shaft connection 28. Bell housing cover
29. Stay (R.H.)
30. Centermember assembly
69-78 Nm
,
31. plate bolts
32. mounting bolts
33. bracket
34. Transaxle assembly
Cautionindicates parts should be temporarily tightened,
and then fully tightened the on the groundin the unladen condition. For tightening locations by the symbol, firsttighten temporarily, and then make the final with the entire weight of the engine applied to the body.
TSBRevision

AUTOMATICTRANSAXLE
ENGINE (TURBO) AND ENGINE> Transaxle Assembly
Engine>
Pre-removalOperationl Transaxle Fluid Draining(Refer to GROUP 00 Maintenance Service.)l Battery Removall Under Cover Removal(Refer to GROUP 42 Under Cover.)I
I
I
Post-installation Operationl Battery Installationl Under Cover Installation(Refer to GROUP 42 Under Cover.)l Transaxle Fluid Supplying(Refer to GROUP 00 Maintenance Service.)l Selector Lever Operation Check
30 Nm
5915
44Nm
TSB Revision
Removal steps
1. Air cleaner cover and air intakehose assembly2. Air cleaner element
3. Battery tray
4. Battery tray stay
5. Transaxle control cable connection
6. Oil dipstick and guide assembly7. Starter motor
8. Park/Neutral position switch
connector9. Oil temperature sensor connector
10. Kick down servo switch connector11. Solenoid valve connector
12. Pulse generator connector
13. Speedometer
14. Transaxle assembly mounting bolts
15. roll stopper bracket mounting
16. Transaxle mounting bracket mount-
ing nuts17. Transaxle oil cooler l Supporting engine assembly