cvt NISSAN NOTE 2016 Service Repair Manual

AV-110
< SYMPTOM DIAGNOSIS >[DISPLAY AUDIO]
AUDIO SYSTEM
RELATED TO REAR VIEW CAMERA
Symptoms
Check itemsProbable malfunction location
Does not recognize cellular phone connec-
tion (no connection is displayed on the dis-
play at the guide). Repeat the registration of cellular phone.
Malfunction in audio unit.
Refer to AV- 7 1 , "
On Board Diagnosis Func-
tion".
Hands-free phone cannot be established. • Hands-free phone operation can be
made, but the communication cannot be
established.
• Hands-free phone operation can be per-
formed, however, voice between each
other cannot be heard during the conver-
sation.
The other party’s voice cannot be heard by
hands-free phone. Check the “microphone speaker” in Inspec-
tion & Adjustment Mode if sound is heard.
Originating sound is not heard by the other
party with hands-free phone communica-
tion. Sound operation function is normal.
Sound operation function does not work.
Microphone signal circuit malfunction.
Refer to
AV- 1 0 2 , "
Diagnosis Procedure".
The system cannot be operated. Steering switch’s , , and
switch works, but does not work.
Steering switch malfunction.
Replace steering switch. Refer to
AV- 1 2 1 ,
"Removal and Installation".
Steering switch’s , , , and switches do not work. Steering switch signal circuit malfunction.
Refer to
AV- 1 0 4 , "
Diagnosis Procedure".
All steering switches do not work. Steering switch ground circuit malfunction.
Refer to
AV- 1 0 4 , "
Diagnosis Procedure".
Symptoms Check itemsProbable malfunction location
Rear view camera is inoperative. Reverse signal circuit malfunction.
Reverse signal circuit malfunction between
transmission range switch (with CVT) or
park/neutral position
(PNP) switch (back-
up) (with M/T) and audio unit.
Refer to AV- 1 0 0 , "
Diagnosis Procedure".
Camera image signal circuit malfunction. Camera image signal circuit malfunction
between rear view camera and audio unit.
Refer to AV- 1 0 0 , "
Diagnosis Procedure".
Rear view camera malfunction. Replace rear view camera.
Refer to AV- 11 8 , "
Removal and Installa-
tion".
Revision: August 2015
2016 Versa Note

cardiagn.com

AV-144
< SYSTEM DESCRIPTION >[NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
3. While pressing the APPS button, turn the TUNE dial counter-
clockwise 5 or more clicks, then clockwise 5 or more clicks, then
counterclockwise 5 or more clicks. Shifting from current screen
to previous screen is performed by pressing BACK button.
4. The trouble diagnosis initial screen is displayed, and Version, User Configuration, Radio, Syst em State or Self Test can be
selected.
CONSULT FunctionINFOID:0000000012433016
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
Refer to AV-151, "DTC Index".
DATA MONITOR
CONFIGURATION
Refer to AV-175, "CONFIGURATION (AV CONTROL UNIT) : Description".
CAN DIAG SUPPORT MNTR
AWNIA3744ZZ
AWNIA3745ZZ
Direct Diagnostic Mode Description
ECU Identification The AV control unit part number is displayed.
Self Diagnostic Result The AV control unit self diagnostic results are displayed.
Data Monitor The AV control unit input/output data is displayed in real time.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr • The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off] Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off] Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off] Indicates condition of ignition signal.
REV SIG [On/Off] Indicates condition of reverse signal received from transmission range switch (with CVT)
or park/neutral position (PNP) switch (back-up) (with M/T).
Revision: August 2015
2016 Versa Note

cardiagn.com

AV
MULTI AV SYSTEMAV-231
< SYMPTOM DIAGNOSIS > [NAVIGATION]
C
D
E
F
G H
I
J
K L
M B A
O P
Camera image is rolling. Camera image signal circuit (output)
malfunction. Camera image signal circuit (output) malfunction be-
tween around view monitor control unit and AV control
unit.
Refer to
AV- 1 5 2 , "
Reference Value".
Display does not switch to rear view
monitor even when selector lever is
in R (reverse). Reverse signal circuit malfunction. Reverse signal circuit between transmission range
switch (with CVT) or park/neutral position (PNP)
switch (back-up) (with M/T) and around view monitor
control unit.
Refer to
AV- 1 5 2 , "
Reference Value".
Predicted course line display in front
view and rear view is malfunction-
ing. Steering angle sensor malfunction. Predicted course line center position is malfunction-
ing.
Refer to
AV- 1 7 9 , "
PREDICTED COURSE LINE CEN-
TER POSITION ADJUSTMENT : Work Procedure".
Front view and front of birds-eye
view is not displayed. • Front camera malfunction.
• Front camera image signal circuit mal-
function. • Front camera power supply and ground circuits
malfunction.
• Front camera image signal circuit malfunction be- tween front camera and around view monitor con-
trol unit.
Refer to AV- 1 9 4 , "
Diagnosis Procedure".
Rear view and rear of birds-eye
view is not displayed. • Rear view camera malfunction.
• Rear view camera image signal circuit
malfunction. • Rear view camera power supply and ground cir-
cuits malfunction.
• Rear view camera image signal circuit malfunction between rear view camera and around view moni-
tor control unit.
Refer to AV- 1 8 8 , "
Diagnosis Procedure".
Driver side of birds-eye view is not
displayed. • Side camera LH malfunction.
• Side camera LH image signal circuit
malfunction. • Side camera LH power supply and ground circuits
malfunction.
• Side camera LH image signal circuit malfunction
between side camera LH and around view monitor
control unit.
Refer to AV- 1 9 6 , "
Diagnosis Procedure".
Front-side and passenger side of
birds-eye view is not displayed. • Side camera RH malfunction.
• Side camera RH image signal circuit
malfunction. • Side camera RH power supply and ground circuits
malfunction.
• Side camera RH image signal circuit malfunction between side camera RH and around view monitor
control unit.
Refer to AV- 1 9 2 , "
Diagnosis Procedure".
Selector lever is in a position other
than R (reverse) and front, rear,
front-side and Birds-Eye views are
displayed even as vehicle speed in-
creases. Vehicle speed signal malfunction.
Vehicle speed signal malf
unction between ABS actu-
ator and electric unit (control unit) and around view
monitor control unit.
Refer to AV- 1 5 2 , "
Reference Value".
Symptoms
Check items Probable malfunction location
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-24
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
PUSH SWITCH INDICATOR
This test is able to check push-button ignition switch indicator operation [On/Off].
INT LAMP This test is able to check interior room lamp operation [On/Off].
INDICATOR This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
FLASHER This test is able to check hazard lamp operation [LH/RH/Off].
OUTSIDE BUZZER This test is able to check Intelligent Key warning buzzer operation [On/Off].
HORN This test is able to check horn operation [On].
P RANGE This test is able to check CVT shift selector illumination operation [On/Off].
Test Item
Description
Support ItemSetting Description
LOCK/UNLOCK BY I-KEY On*
Door lock/unlock function from Intelligent Key ON.
Off Door lock/unlock function from Intelligent Key OFF.
ANTI KEY LOCK IN FUNCTI On*
Anti lock out setting ON.
Off Anti lock out setting OFF.
ANS BACK I-KEY UNLOCK Off
No buzzer reminder when doors are unlocked with request switch.
On* Buzzer reminder when doors are unlocked with request switch.
ANS BACK I-KEY LOCK Horn Chirp
Horn chirp reminder when doors are locked with request switch.
Buzzer* Buzzer reminder when doors are locked with request switch.
Off No reminder when doors are locked with request switch.
HORN WITH KEYLESS LOCK Off
Horn chirp reminder when doors are locked with Intelligent Key.
On* No horn chirp reminder when doors are locked with Intelligent Key.
HAZARD ANSWER BACK Lock/Unlock*
Hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
Unlock Only Hazard warning lamp activation when doors are unlocked with Intel-
ligent Key or request switch.
Lock Only Hazard warning lamp activation when doors are locked with Intelli-
gent Key or request switch.
Off No hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
INSIDE ANT DIAGNOSIS —This function allows inside key antenna self-diagnosis.
CONFIRM KEY FOB ID —Intelligent Key ID code can be checked.
SHORT CRANKING OUTPUT Start70 msec
Starter motor operation duration time setting.
100 msec
200 msec
End —
PANIC ALARM SET MODE 3 1.5 sec
Intelligent Key panic alarm button setting.
MODE 2 OFF
MODE 1* 0.5 sec
LO- BATT OF KEY FOB WARN On*
Intelligent Key low battery warning ON.
Off Intelligent Key low battery warning OFF.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-47
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
1: With CVT
2: With M/T 90
(W) Ground Push-button ignition
switch illumination
power supply OutputPush-button ig-
nition switch il-
lumination ON
Battery voltage
OFF 0 – 1.5 V
91
(V) Ground ACC/ON indicator
lamp
OutputPush-button ig-
nition switch OFF
Battery voltage
ACC or ON 0 – 1.5 V
92
(B) Ground Push-button ignition
switch illumination
lamp Output
Push-button ig-
nition switch il-
lumination ON
5.5 V
OFF 0 – 1.5 V
93
(R) Ground Intelligent Key warn-
ing buzzer OutputIntelligent Key
warning buzzer Sounding
0 – 1.5 V
Not sounding Battery voltage
96
(SB) Ground Accessory relay
control OutputIgnition Push-
button switch OFF
0 – 0.5 V
ACC or ON Battery voltage
97
(R) Ground Starter relay control Output Push-button ig-
nition switch ONSelector lever in P (Park)
or N (Neutral) position
Battery voltage
Selector lever not in P
(Park) or N (Neutral) posi-
tion 0 – 0.5 V
98
(BG) Ground Ignition relay (IPDM
E/R) control OutputPush-button ig-
nition switch OFF or ACC
Battery voltage
ON 0 – 0.5 V
99
(GR) Ground Ignition relay (F/B)
control OutputPush-button ig-
nition switch OFF or ACC
0 – 0.5 V
ON Battery voltage
100 (L) Ground Request sw (AS)
signal InputPassenger door
request switch ON (Pressed)
0 – 1.5 V
OFF (Not pressed) Battery voltage
101 (V) Ground Clutch interlock
switch
InputClutch interlock
sw
itch OFF (c
l
utch pedal is not
depressed) 0V
ON (clutch pedal is de-
pressed) Battery voltage
102
1
(BR) Ground P/N position
Input Selector leverSelector lever in P (Park)
or N (Neutral) position
Battery voltage
Selector lever not in P
(Park) or N (Neutral) posi-
tion 0 – 1.5 V
102
2
(BR) Ground Neutral sw
Input Selector leverSelector lever in N (Neu-
tral) position
Battery voltage
Selector lever not in N
(Neutral) position 0 – 1.5 V
103
(LG) Ground Front defrost switch Input
——
104 (V) Ground CVT shift selector
(park position
switch) power sup-
ply Output Push-button ignition switch ON
Battery voltage
105
(SB) Ground Stop lamp switch 2 Input Push-button ignition switch OFF
Battery voltage
106 (Y) Ground Blower relay control Output
Push-button ig-
nition switchOFF or ACC
0 – 0.5 V
ON Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-60
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration ListINFOID:0000000012432341
CAUTION:
• Thoroughly read and understand the vehicle speci fication. ECU control may not operate normally if
the setting is not correct.
• The “setting value” of this vehicle is as follows: Never select any other value than the setting value
shown below. (If there is only 1 item in “setting value” that means that item is the only choice for this
certain vehicle.)
⇔ : Items which confirm vehicle specifications SETTING ITEM
NOTE
Items Setting value
I-KEY SYS FREQUENCY TYPE MODE2 ⇔ MODE3 • MODE2: 315 MHz
• MODE3: 433.92 MHz
TRANSMISSION AT with ABS ⇔ MT with ABS • AT with ABS: CVT models
• MT with ABS: M/T models
THEFT ALM AREA MODE2 ⇔ WITHOUT • MODE2: With vehicle security system
• WITHOUT: Without vehicle security system
ASCD CANCEL SW TYPE MODE1 ⇔ MODE2 • MODE1: With ASCD and CVT
• MODE2: With ASCD and M/T
AUTO DOOR LOCK SELECT WITH ⇔ WITHOUT • WITH: With automatic door lock function
• WITHOUT: Without automatic door lock function
I-KEY TUNING MODE2 —
DTRL MODE2 ⇔ WITHOUT • MODE2: With daytime running lamps
• WITHOUT: Without daytime running lamps
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS-124
< BASIC INSPECTION >[WITHOUT INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration ListINFOID:0000000012432398
CAUTION:
• Thoroughly read and understand the vehicle speci fication. ECU control may not operate normally if
the setting is not correct.
• The “setting value” of this vehicle is as follows: Never select any other value than the setting value
shown below. (If there is only 1 item in “setting value” that means that item is the only choice for this
certain vehicle.)
⇔ : Items which confirm vehicle specifications SETTING ITEM
NOTE
Items Setting value
CAN CONNECTION UNIT MODE4 ⇔ WITHOUT • MODE4: With CVT
• WITHOUT: Without CVT
KEYLESS ENTRY WITH ⇔ WITHOUT • WITH: With remote keyless entry
• WITHOUT: Without remote keyless entry
AUTO LOCK & UNLOCK FUNC WITH ⇔ WITHOUT • WITH: With auto door lock function
• WITHOUT: With auto door lock function
Revision: August 2015
2016 Versa Note

cardiagn.com

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-37
< ECU DIAGNOSIS INFORMATION > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
RR RH OUT SOL Operation status of all solenoid valves Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) Off
RR LH IN SOL Operation status of all solenoid valves Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) Off
RR LH OUT SOL Operation status of all solenoid valves Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator
relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) Off
EBD WARN LAMP EBD warning lamp
(Note 2) When EBD warning lamp is ON
On
When EBD warning lamp is OFF Off
STOP LAMP SW Brake pedal operation When brake pedal is depressed
On
When brake pedal is not depressed Off
MOTOR RELAY Motor and motor relay operation When the motor relay and motor are op-
erating
On
When the motor relay and motor are not
operating Off
ACTUATOR RLY Actuator relay operation When the actuator relay is operating
On
When the actuator relay is not operating Off
ABS WARN LAMP ABS warning lamp
(Note 2) When ABS warning lamp is ON
On
When ABS warning lamp is OFF Off
OFF LAMP VDC OFF indicator lamp
(Note 2) When VDC OFF indicator lamp is ON
On
When VDC OFF indicator lamp is OFF Off
OFF SW VDC OFF switch When VDC OFF switch is in ON
On
When VDC OFF switch is in OFF Off
SLIP/VDC LAMP SLIP indicator lamp
(Note 2) When SLIP indicator lamp is ON
On
When SLIP indicator lamp is OFF Off
BATTERY VOLT Battery voltage supplied
to the ABS actuator
and electric unit (control unit) Ignition switch ON
10 – 16 V
GEAR Manual mode gear position determined by
TCM 1st gear
2nd gear
3rd gear
4th gear
5th gear 1
2
3
4
5
SLCT LVR POSI Selector lever position. Vehicle stoppedN/P
ENGINE SPEED With engine runn ingWhen engine running RPM
YAW RATE SEN Yaw rate detected by yaw rate/side G sensor When vehicle stop
Approx. 0 d/s
When vehicle turning -75 to 75 d/s
R POSI SIG Transmission range switch signal ON/OFF
condition CVT shift position = R position
On
CVT shift position = other than R position Off
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-38
< ECU DIAGNOSIS INFORMATION >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
N POSI SIGTransmission range switch signal ON/OFF
condition CVT shift position = N position
On
CVT shift position = other than N position Off
P POSI SIG Transmission range switch signal ON/OFF
condition CVT shift position = P position
On
CVT shift position = other than P position Off
CV1 ABS actuator cut valve 1 When the cut valve is active
On
When the cut valve is inactive Off
CV2 ABS actuator cut valve 2 When the cut valve is active
On
When the cut valve is inactive Off
SV1 ABS actuator suction valve When the suction valve is active
On
When the suction valve is inactive Off
SV2 ABS actuator suction valve 2 When the suction valve is active
On
When the suction valve is inactive Off
ACCEL POS SIG Throttle actuator opening/closing is dis-
played (linked with accelerator pedal) Accelerator pedal not depressed (ignition
switch is ON)
0 %
Depress accelerator pedal (ignition
switch is ON) 0 - 100 %
SIDE G-SENSOR Transverse G detected by side G sensor Vehicle stopped
Approx. 0 m/s
2
Vehicle turning rightNegative value
(m/s2)
Vehicle turning left Positive value
(m/s
2)
STR ANGLE SIG Steering angle detected by steering angle
sensor Straight-ahead
Approx. 0°
Steering wheel turned –720 to 720°
PRESS SENSOR Brake fluid pressure detected by pressure
sensor With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed –40 to 300 bar
EBD SIGNAL EBD operation EBD is active
On
EBD is inactive Off
ABS SIGNAL ABS operation ABS is active
On
ABS is inactive Off
TCS SIGNAL TCS operation TCS is active
On
TCS is inactive Off
VDC SIGNAL VDC operation VDC is active
On
VDC is inactive Off
EBD FAIL SIG EBD fail-safe signal In EBD fail-safe
On
EBD is normal Off
ABS FAIL SIG ABS fail-safe signal In ABS fail-safe
On
ABS is normal Off
TCS FAIL SIG TCS fail-safe signal In TCS fail-safe
On
TCS is normal Off
VDC FAIL SIG VDC fail-safe signal In VDC fail-safe
On
VDC is normal Off
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: August 2015 2016 Versa Note

cardiagn.com

C1116 STOP LAMP SWITCHBRC-87
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2. Disconnect stop lamp switch harness connector.
3. Check the continuity between ABS actuator and electric unit (control unit) harness connector and stop lamp switch harness connector.
4. Check the continuity between ABS actuator and el ectric unit (control unit) harness connector and the
ground.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness or connector, and GO TO 10.
10.CHECK DATA MONITOR (3)
With CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect stop lamp switch harness connector.
3. Erase “Self Diagnostic Result” of “ABS”
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
NOTE:
Stop the vehicle.
6. Select “DATA MONITOR” of “ABS”, check “STOP LA MP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-36, "
Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "
Removal and Instal-
lation".
Component InspectionINFOID:0000000012430868
1.CHECK STOP LAMP SWITCH
1. Turn the ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check the continuity when stop lamp switch is operated.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the stop lamp switch. Refer to BR-20, "
Removal and Installation".
ABS actuator and electric unit (control unit) Stop lamp switch
Continuity
Connector TerminalConnector Terminal
E33 12E13 (WITH CVT)
2Yes
E57 (WITH M/T)
ABS actuator and electric unit (control unit)
—Con tin uit y
Connector Terminal
E33 12Ground No
Stop lamp switch
Condition Continuity
Te r m i n a l
1 – 2 When stop lamp switch is released
(When brake pedal is depressed) Ye s
When stop lamp switch is pressed (When brake pedal is released) No
Revision: August 2015
2016 Versa Note

cardiagn.com