Key NISSAN TEANA 2014 Service Manual

DLK-198
< REMOVAL AND INSTALLATION >
DOOR HANDLE
• Do not reuse inside door handle escutcheon. Replace with new part after removal.
• Check front door lock cables are pr operly engaged to inside handle.
• After installation, check front doo r open/close, lock/unlock operation.
FRONT DOOR HANDLE : Removal and Installation - Outside HandleINFOID:0000000009461945
REMOVAL
1. Fully close front door glass.
2. Remove front door finisher. Refer to INT-15, "Removal and Installation"
.
3. Remove front door vapor barrier.
4. Remove front door glass channel rear.
5. Disconnect the harness connectors from the door antenna and door request switch and then remove har-
ness clamp on outside handle bracket.
6. Remove door side grommet, and loosen screw that retains the front door outside handle bracket.
7. Reach in to separate door key cylinder rod (LH side) (1) from door key cylinder assembly (LH side).
8. While pulling outside handle (1), remove door key cylinder assembly (LH side) or outside handle escutcheon (2) (RH side).
JMKIA0025ZZ
ALKIA2487ZZ
JMKIA0560ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR HANDLEDLK-199
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
9. While pulling outside handle (1), slide toward rear of vehicle to remove outside handle.
10. Remove front gasket (1) and rear gasket (2). : Front
11. Slide outside handle bracket toward rear of vehicle to remove. : Front
12. Disconnect the outside handle cable from the outside handle bracket connection.
INSTALLATION
Installation is in the reverse order of removal.
Tighten front door outside handle bracket screw to specified torque.
CAUTION:
• When installing do not reuse front door outs ide handle bracket screw. Always replace screw with
new ones when removed.
• When installing door key cylinder rod on the LH fron t door, be sure to rotate door key cylinder rod
holder until a click is felt.
AWKIA1997ZZ
JMKIA5889ZZ
JMKIA5890ZZ
PIIB5815E
Front door outside handle
bracket screw 5.8 N·m (0.59 kg-m, 51 in-lb)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR LOCKDLK-203
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK
FRONT DOOR LOCK
FRONT DOOR LOCK : Exploded ViewINFOID:0000000009461949
FRONT DOOR LOCK : Removal and InstallationINFOID:0000000009461950
CAUTION:
Before servicing, turn igni tion switch OFF, disconnect both batt ery terminals and wait at least three
minutes.
REMOVAL
1. Remove the front door outside handle. Refer to DLK-198, "FRONT DOOR HANDLE : Removal and Instal-
lation - Outside Handle".
2. Remove the rear glass run.
3. Disconnect the harness connector from the front door lock actuator.
1. Outside handle escutcheon 2. Rear gasket 3. Screw
4. Door key cylinder rod (driver side) 5. Front door lock assembly 6. Cable clip
7. Inside door handle escutcheon 8. Inside handle 9. Outside handle bracket
10. Front gasket 11. Outside handle 12. Door key cylinder assembly (driv- er side only)
Front
ALKIA2713ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-204
< REMOVAL AND INSTALLATION >
DOOR LOCK
4. Remove screws, and the door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
• Tighten front door lock screws to specified torque.
CAUTION:
• Do not reuse inside door handle escutcheon. Replace with new part after removal.
• Do not reuse front door lock assembly screw s. Always replace screws with new ones when
removed.
• Check front door lock cables are properly engage d to inside handle and outside handle bracket.
• When installing door key cylinder rod on the LH front door, be sure to rotate door key cylinder rod
holder until a click is felt.
• After installation, check front doo r open/close, lock/unlock operation.
• Check front door lock assembly for poor lubricatio n. If necessary apply a suitable multi-purpose
grease.
REAR DOOR LOCK
REAR DOOR LOCK : Exploded ViewINFOID:0000000009461951
PIIB5812E
Front door lock screw 5.8 N·m (0.59 kg-m, 51 ft-lb)
ALKIA2714ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

KEY CYLINDERDLK-217
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
KEY CYLINDER
GLOVE BOX LID KEY CYLINDER
GLOVE BOX LID KEY CYLINDER : Removal and InstallationINFOID:0000000009461965
REMOVAL
1. Remove glove box assembly (2) to access glove box lid key cyl-
inder (1). Refer to IP-22, "Removal and Installation"
.
2. Insert key (1) into glove box lid lock cylinder (2).
3. Pull upward on glove box lid release handle (3).
4. Rotate key (1) and turn glove box lid key cylinder (2) to the lock position.
5. Press tumbler stopper (1) into glove box lid lock cylinder (2) using a suitable tool (A), and then remove key (3) and glove box
lid lock cylinder together from glove box lid release handle (4).
NOTE:
When removing glove box lid lock cylinder (2) note the position
of cylinder to glove box lid release handle (4).
6. Remove sleeve (3) from glove box lid release handle and then install sleeve to glove box lid lock cylinder.
NOTE:
When removing sleeve note the position of sleeve to glove box
lid release handle.
CAUTION:
Do not pull out key (1) from glove box lid lock cylinder (2)
while sleeve (3) is removed. Othe rwise, tumblers (4) may be
lost from glove box lid lock cylinder.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check glove box assem bly open/close, lock/unlock operation.
ALKIA2719ZZ
JMKIA5490ZZ
JMKIA5491ZZ
JMKIA5819ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-218
< REMOVAL AND INSTALLATION >
KEY CYLINDER
SEATBACK LOCK KEY CYLINDER
SEATBACK LOCK KEY CYLINDER : Removal and InstallationINFOID:0000000009461966
REMOVAL
1. Remove rear parcel shelf finisher. Refer to INT-26, "Removal and Installation".
2. Remove bolts (A) and the setback lock key cylinder (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, rear seatback assembl y open/close, lock/unlock operation.
ALKIA2738ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-220
< REMOVAL AND INSTALLATION >
INSIDE KEY ANTENNA
INSIDE KEY ANTENNA
CONSOLE
CONSOLE : Removal and InstallationINFOID:0000000009461968
REMOVAL
1. Remove the center console rear finisher (1). Refer to IP-18,
"Removal and Installation".
2. Remove the inside key antenna (console) screws (A) and inside key antenna (console) (2).
INSTALLATION
Installation is in the reverse order of removal.
LUGGAGE ROOM
LUGGAGE ROOM : Removal and InstallationINFOID:0000000009461969
REMOVAL
1. Disconnect the harness connector (A) from the inside keyantenna (luggage room) (1).
2. Remove the inside key antenna (luggage room) clips (B), and then remove inside key antenna (luggage room) (1).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2720ZZ
ALKIA2721ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

OUTSIDE KEY ANTENNADLK-221
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Removal and InstallationINFOID:0000000009461970
REMOVAL
The driver side outside key antenna and driver side outside handle are serviced as an assembly. Refer to
DLK-198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
INSTALLATION
Installation is in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and InstallationINFOID:0000000009461971
REMOVAL
The passenger side outside key antenna and passenger side outside handle are serviced as an assembly.
Refer to DLK-198, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
INSTALLATION
Installation is in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Remo val and InstallationINFOID:0000000009461972
REMOVAL
1. Remove rear bumper fascia. Refer to EXT-21, "Removal and Installation".
2. Disconnect the harness connector (B) from the rear bumper key
antenna (1).
3. Remove the nuts (A) that retain the rear bumper key antenna (1) to the body.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2723ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

INTELLIGENT KEY WARNING BUZZERDLK-223
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
INTELLIGENT KEY WARNING BUZZER
Removal and InstallationINFOID:0000000009461975
REMOVAL
NOTE:
The Intelligent Key warning buzzer is located in the left front area of the engine compartment.
1. Remove the Intelligent Key warning buzzer harness clip.
2. Remove the nut (B) that retains the Intelligent Key warning buzzer (1) to the body.
3. Disconnect the harness connector (A) from the Intelligent Key warning buzzer (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2728ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-224
< REMOVAL AND INSTALLATION >
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Removal and InstallationINFOID:0000000009461976
REMOVAL
1. Remove glove box assembly. Refer to IP-22, "Removal and Installation".
2. Disconnect the harness connector (A) from the remote keyless entry receiver (1).
3. Remove the screw (B) and remote keyless entry receiver (1).
INSTALLATION
Installation is in the reverse order or removal.
ALKIA2725ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM