NISSAN TEANA 2014 Service Manual

WHEEL SENSORBRC-125
< REMOVAL AND INSTALLATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Installation is in the reverse order of removal.
CAUTION:
Do not twist front wheel sensor harness when installing front
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that front wheel sensor harness is not
twisted after installation.
Exploded View - Rear Wheel SensorINFOID:0000000009463848
Removal and Installati on - Rear Wheel SensorINFOID:0000000009463849
CAUTION:
• Be careful not to damage wheel sensor edge and sensor rotor teeth.
• When removing the front or rear wheel hub, firs t remove the wheel sensor from the wheel hub. Fail-
ure to do so may result in damage to the wh eel sensor wires making the sensor inoperative.
• Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sen-
sor harness.
• Before installation, check if foreig n objects such as iron fragments are adhered to the pick-up part of
the sensor or to the inside of the hole in the wheel hub for the wheel sensor, or if a foreign object is
JPFIC0209ZZ
1. Rear wheel sensor A. Rear wheel sensor bracket B. Clip
C. Rear wheel sensor harness connector Front
AWFIA0927ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-126
< REMOVAL AND INSTALLATION >[VDC/TCS/ABS]
WHEEL SENSOR
caught in the surface of the mating surface for the
sensor rotor. Fix as necessary and then install the
wheel sensor.
REMOVAL
1. Remove the rear wheels and tires using power tool. Refer to WT-55, "Adjustment".
2. Disconnect the rear wheel sensor harness connector.
3. Remove the rear wheel sensor from the rear wheel sensor brackets and clips.
4. Remove the rear wheel sensor hold down bolt and remove the rear wheel senor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not twist rear wheel senso r harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not twisted
after installation.
JPFIC0209ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SENSOR ROTORBRC-127
< REMOVAL AND INSTALLATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
SENSOR ROTOR
Removal and Installation - Front Sensor RotorINFOID:0000000009463850
The front wheel sensor rotor is an integral part of the wheel hub and bearing assembly and cannot be disas-
sembled. Refer to FAX-8, "Removal and Installation"
.
Removal and Installation - Rear Sensor RotorINFOID:0000000009463851
The rear wheel sensor rotor is an integral part of the wheel hub and bearing assembly and cannot be disas-
sembled. Refer to RAX-6, "Removal and Installation"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-128
< REMOVAL AND INSTALLATION >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
Exploded ViewINFOID:0000000009463852
Removal and InstallationINFOID:0000000009463853
CAUTION:
• When replacing the ABS actuator and electric unit (c ontrol unit), the calibration of the ABS actuator
and electric unit (control unit) is required. Refer to BRC-57, "Description"
.
• Before servicing, disconnect the ba ttery cable from negative terminal.
• To remove brake tubes, use a suitable tool (flare nut wrench) to prevent flare nuts and brake tubes
from being damaged. To install, use su itable tool (flare nut torque wrench).
• Do not apply excessive impact to ABS actuator and elect ric unit (control unit), such as by dropping
it.
• Do not remove and install ABS actuator and el ectric unit (control unit) by holding harness.
• After work is completed, bleed air from brake tubes. Refer to BR-14, "Bleeding Brake System"
.
• After installing harness connector on the ABS act uator and electric unit (control unit), make sure
connector is securely locked.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect battery cable from negative terminal. Refer to PG-73, "Removal and Installation (Battery)".
2. Remove cowl top and cowl top extensions. Refer to EXT-24, "Removal and Installation"
.
1. ABS actuator and electric unit (con-
trol unit) 2. Bracket A. ABS actuator an
d electric unit (con-
trol unit) harness connector
B. To master cylinder secondary side 23 N-m (2.3 kg-m, 17 ft-lb) C. To master cylinder primary side
23 N-m (2.3 kg-m, 17 ft-lb) D. To rear LH
16.2 N-m (1.7kg-m, 12 ft-lb)
E. To front RH 16.2 N-m (1.7kg-m, 12 ft-lb) F. To f r o n t L H
16.2 N-m (1.7kg-m, 12 ft-lb) G. To rear RH
16.2 N-m (1.7kg-m, 12 ft-lb)
Front
ALFIA0316ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-129
< REMOVAL AND INSTALLATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
3. Remove the power steering line hold down bracket.
4. Disconnect ABS actuator and el ectric unit (control unit) harness connector and place aside.
5. Loosen brake tube flare nuts using a suitable tool, t hen remove brake tubes from ABS actuator and elec-
tric unit (control unit) and place aside. Refer to BRC-128, "Exploded View"
.
6. Remove the harness bracket bolt and place aside.
7. Remove ABS actuator and electric unit (control unit) and bracket as an assembly.
8. Remove bracket from ABS actuator and el ectric unit (control unit), if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
If ABS actuator and electronic unit (control unit) is replaced, after installation, adjust position of steer-
ing angle sensor. Refer to BRC-58, "Work Procedure"
.
ALFIA0306ZZ
ALFIA0302ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-130
< REMOVAL AND INSTALLATION >[VDC/TCS/ABS]
VDC OFF SWITCH
VDC OFF SWITCH
Removal and InstallationINFOID:0000000009463854
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-21, "Removal and Installation".
2. Remove the switch plate screw s and remove the switch plate.
3. Release pawls (B) using suitable tool and remove the VDC OFF switch (A).
: pawl
INSTALLATION
Installation is in the reverse order of removal.
ALFIA0307ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

YAW RATE/SIDE/DECEL G SENSORBRC-131
< REMOVAL AND INSTALLATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
YAW RATE/SIDE/DECEL G SENSOR
Removal and InstallationINFOID:0000000009463855
The yaw rate/side/decel G sensor is an integral part of the ABS actuator and electrical control unit (control
unit) and cannot be disassembled. Refer to BRC-128, "Removal and Installation"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-132
< REMOVAL AND INSTALLATION >[VDC/TCS/ABS]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Exploded ViewINFOID:0000000009463856
Removal and InstallationINFOID:0000000009463857
REMOVAL
1. Remove spiral cable assembly. Refer to
SR-15, "Removal and Installation".
2. Remove the two screws and the steering angle sensor from spiral cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse steering angle sensor.
• Perform the neutral position adjustment of the steering angle sensor. Refer to BRC-58, "Work Proce-
dure".
1. Steering angle sensor A. Screw Front
ALFIA0235ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRM-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D E
F
G H
I
J
L
M
SECTION BRM
A
B
BRM
N
O P
CONTENTS
BODY REPAIR
VEHICLE INFORMATION ... ..........................2
BODY EXTERIOR PAINT COLOR ................ .....2
Body Exterior Paint Color ................................. ......2
PRECAUTION ...............................................3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
HANDLING PRECAUTIONS FOR PLASTICS .....4
Precautions For Plastics .................................... ......4
PRECAUTIONS IN REPAIRING HIGH
STRENGTH STEEL ........................................ .....
7
High Strength Steel (HSS) ................................ ......7
Handling of Ultra High Strength Steel Plate Parts ......9
PREPARATION ...........................................10
REPAIRING MATERIAL ................................ ....10
Foam Repair ....................................................... ....10
BODY COMPONENT PARTS ............................13
Underbody Component Parts ............................ ....13
Body Component Parts ...........................................15
REMOVAL AND INSTALLATION ...............17
CORROSION PROTECTION ......................... ....17
Description .......................................................... ....17
Anti-Corrosive Wax ............................................. ....17
Undercoating ...........................................................18
BODY SEALING ...............................................20
Description ...............................................................20
REPLACEMENT OPERATIONS .......................23
Description ...............................................................23
Hoodledge ...............................................................26
Front Side Member (Partial Replacement) ...........28
Front Pillar ..............................................................28
Dash Side ................................................................36
Center Pillar .............................................................37
Roof .........................................................................42
Outer Sill .................................................................46
Rear Fender ............................................................49
Rear Panel ..............................................................50
Rear Floor Rear .....................................................51
Rear Side Member Extension ...............................52
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .............................................
53
BODY ALIGNMENT ..........................................53
Body Center Marks ............................................ ....53
Description ...............................................................54
Engine Compartment ..............................................54
Underbody ...............................................................56
Passenger Compartment ........................................58
Rear Body ................................................................62
Revision: November 20132014 Altima NAM

BRM-2
< VEHICLE INFORMATION >
BODY EXTERIOR PAINT COLOR
VEHICLE INFORMATION
BODY EXTERIOR PAINT COLOR
Body Exterior Paint ColorINFOID:0000000009464961
M = Metallic, S = Solid, 2S = Solid and Clear, 2P = 2-Coat Pearl, 3P = 3-Coat Pearl, PM = Pearl Metallic, t = Primerless Diamond Clear
coat, Cr2P = Chromium plate, Black is solvent based, all others are water based.
AWKIA2219ZZ
Component Color code CAJ K23 KAH KH3 NAH QAB RBD KAD
Description Brown Silver Beige Black Red White Blue Grey
Paint type MMMSMPM M
Hard clear coatttttttt t
1. Outside door handle Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
2. Fuel filler lid Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
3. Rear bumper fascia Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
4. License lamp finisher Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
5. Lower rocker finisher Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
6. Body side molding Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
7. Door mirror Finisher Body co lor CAJ K23 KAH KH3 NAH QAB RBD KAD
8. Front bumper fascia Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
9. Front grille Center Black KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3
Surround Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
Revision: November 20132014 Altima NAM