NISSAN X-TRAIL 2001 Service Repair Manual

SUNROOF
RF-3
C
D
E
F
G
H
J
K
L
MA
B
RF
SUNROOFPFP:91210
System DescriptionEIS000MK
●Operating sunroof switch allows glass lid open/close, and tilt UP·DOWN.
●When sunroof switch is pressed firmly toward the OPEN side, glass lid automatically opens and automatic
operation is stopped at a point 180 mm to the fully open position.
NOTE:
After the emergency handle is used to rotate the motor drive shaft, sunroof switch operation may not cor-
respond to actual glass lid movement. When this happens, conduct resuming operation to restore normal
operation.
RESUMING OPERATION
●If actual glass lid operation does not correspond to expected
operation, operate sunroof switch to slide glass lid toward area
A in the figure. This should result in resumption of normal oper-
ation.
CAUTION:
Before normal operation is resumed, expected sunroof
switch operation and actual glass lid movement may not
correspond. Make sure that neither head nor hands pro-
trude from sunroof and conduct resuming operation.
Component Parts LocationEIS000ML
SIIA0139E
SIIA0321E

RF-4
SUNROOF
Wiring Diagram — SROOF —
EIS000MM
TIWA0001E
SMA for models with roof 
mounted driving lamp

SUNROOF
RF-5
C
D
E
F
G
H
J
K
L
MA
B
RF
TIWA0002E

RF-6
SUNROOF
Terminal and Reference Value for Sunroof Switch
EIS000MN
Wind Deflector InspectionEIS000MO
1. Open glass lid.
2. Visually confirm that the mounting condition is correct.
3. Confirm wind deflector connection is properly greased. If neces-
sary, apply body grease.
4. Confirm wind deflector can be properly raised by hand. If excess
wear or damage is detected, remove and visually check it. If it is
damaged, replace it with a new one. If no damage is found, rein-
stall it properly.
Sunroof Lid Weatherstrip InspectionEIS000MP
If there is water leakage around glass lid, close glass lid and flush with water to determine whether it is from
damaged parts or a gap.
1. Remove glass lid assembly.
2. Visually check weatherstrip for damage, deterioration, or deformation. If excess wear or damage is
detected, replace glass lid assembly.
Link and Wire Assembly InspectionEIS000MQ
1. If the link coating peels off to show the base material and an abnormal noise is heard, replace it.
2. Visually confirm the wire and rail groove are properly greased. If necessary, apply body grease.
TERMI-
NAL WIRE
COLORITEM CONDITIONVOLTAGE(V)
(Approx)
1 Y Sunroof OPEN signal Sunroof switch OPEN operation Battery voltage
2 B Ground — Battery voltage
3 R Sunroof CLOSE signal Sunroof switch CLOSE operation Battery voltage
4 L Sunroof tilt DOWN signal Sunroof switch tilt DOWN operation Battery voltage
5 G Sunroof AUTO OPEN signal Sunroof switch AUTO OPEN operation Battery voltage
6 W Sunroof tilt UP signal Sunroof switch tilt UP operation Battery voltage
SIIA0115E
SIIA0114E

SUNROOF
RF-7
C
D
E
F
G
H
J
K
L
MA
B
RF
Fitting AdjustmentEIS000MR
LONGITUDINAL/LATERAL CLEARANCE ADJUSTMENT
1. Tilt up glass lid to remove side trim.
2. After loosening glass lid mounting nuts, tilt down glass lid.
3. Adjust glass lid according to sections A–A, B–B, C–C as shown in the figure.
4. After adjusting glass lid, tighten nuts to the specified torque.
5. Tilt glass lid 4 to 5 times to check that it smoothly goes up and down
SURFACE MISMATCH ADJUSTMENT
1. Adjust surface height of glass lid and roof panel to 0±1.5 mm
(0±0.059 in) by altering the number of shims between glass lid
and link assembly. (Standard: 2, max: 4)
2. After fitting adjustment, use a hose to flush the entire surface of
the roof with water to check for leaks.
PIIA3748E
SIIA0119E

RF-8
SUNROOF
Removal and Installation
EIS000MS
SIIA0120E

SUNROOF
RF-9
C
D
E
F
G
H
J
K
L
MA
B
RF
SUNROOF UNIT
Removal
CAUTION:
●Removal and installation of sunroof unit require 2 workers.
●When taking sunroof unit out, use shop cloths to protect seats and trim from damage.
●After installing sunroof unit and glass lid, be sure to carry out the leak test to confirm there is no
more leakage.
1. Remove headlining. Refer to EI-29, "
HEADLINING"
2. Disconnect drain hoses.
3. Disconnect interior lamp harness.
4. Remove both unit-side and body-side front bracket mounting
bolts.
5. Remove both unit-side and body-side center and rear bracket
mounting bolts.
6. Remove motor bracket mounting bolt.
7. Remove mounting bolts on the front end and side rails, and
remove sunroof unit from the roof panel.
8. Remove the sunroof unit out of the passenger compartment
while being careful not to damage the seats and trim.
SIIA0130E
SIIA0184E
SIIA0121E
SIIA0183E

RF-10
SUNROOF
Installation
1. After bringing sunroof unit into the passenger compartment,
tighten mounting nuts on the side rails start from the one at the
front reference point.
2. Tighten mounting nuts on the front end.
3. Align the front bracket to lower face of the rail and roof side
mounting face, and tighten bolts. Then tighten bolts on the roof
side.
4. Align the center and rear brackets to lower face of the rail and
roof side mounting face, and tighten bolts. Then tighten bolts on
the roof side.
NOTE:
Install the sunroof bracket evenly so that the roof surface has no
distortion.
5. Tighten bolts on motor bracket.
6. Connect the interior lamp harness.
GLASS LID
Removal
1. Tilt up glass lid.
2. Remove side trim.
3. Confirm the number of shims between glass lid and link, and
remove mounting nut to remove glass lid.
Installation
1. Tighten nuts on glass lid diagonally.
2. After installation, adjust the fit.
SUNSHADE
Removal and installation
1. Remove glass lid.
2. Remove rear drain.
3. Move link assembly to the fully open position.
4. Loosen the mounting screws on the front LH shade slider.
SIIA0122E
SIIA0131E
SIIA0124E

SUNROOF
RF-11
C
D
E
F
G
H
J
K
L
MA
B
RF
5. As shown in the figure, slide shade slider to remove it from the
aluminum rail.
6. Swivel shade toward the left, and remove RH shade from the
aluminum rail.
7. Slide shade forward, and remove rear shade sliders as well.
8. Install in the reverse order of removal.
WIND DEFLECTOR
Removal and installation
1. Remove deflector arm mounting screws.
2. Using a pointed tool, pull up the tabs on the bushing.
NOTE:
Do not reuse the bushing after its tabs are pulled up.
3. Press and pull off the shaft.
4. Install in the reverse order of removal.
SUNROOF MOTOR
Removal
1. Remove headliner.
2. Remove motor mounting screw and mounting nut.
3. Remove the harness connector, and remove the sunroof motor.
NOTE:
●Remove the sunroof motor when the sunroof is in the fully-
closed position.
●Never rotate the removed sunroof motor as a single unit.
Installation
1. Move sunroof motor laterally little by little until the gear is completely engaged onto the wire on sunroof
unit and the mounting surface becomes parallel. Then secure sunroof motor with screws and nuts.
NOTE:
Before installing sunroof motor, be sure to place the link and wire assembly in the symmetrical and fully closed
position.
SIIA0126E
SIIA0127E
SIIA0128E

RF-12
SUNROOF