NISSAN X-TRAIL 2005 Service Repair Manual

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-105
C
D
E
F
G
H
I
J
L
MA
B
LT

RHD MODELS
TKWA1533E

LT-106
PARKING, LICENSE PLATE AND TAIL LAMPS

TKWA1534E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-107
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003C1
PARKING AND TAIL LAMPS
Refer to LT- 3 7 , "Bulb Replacement of Headlamp and Clearance lamp" in “HEADLAMP -CONVENTIONAL
TYPE-” or LT- 2 0 , "
Bulb Replacement of Headlamp and Clearance Lamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
1. Remove license plate lamp mounting screws.
2. Remove lens of license plate lamp.
3. Remove bulb from its socket.
4. Installation is the reverse order of removal.
Removal and Installation EKS003C2
PARKING LAMP
Refer to LT- 3 8 , "Removal and Installation of Headlamp" in “HEADLAMP -CONVENTIONAL TYPE-” or LT- 2 1 ,
"Removal and Installation of Headlamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-31, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from license lamp finisher.
Installation
Installation is the reverse order of removal.License plate lamp : 12V - 5W
PKIA8753E
PKIA5760E
License plate lamp mounting screws
: 1.4 N·m (0.15 kg-m, 13 in-lb)

LT-108
FRONT FOG LAMP

FRONT FOG LAMP PFP:00011
System Description EKS003DF
DESCRIPTION
Power is supplied at all times

through 10A fuse (No. 31, located in fuse and fusible link box)

to lighting switch terminal 11,

through 15A fuse (No. 42, located in fuse and fusible link box)

to front fog lamp relay terminal 3.
With the lighting switch in the 2ND position, power is supplied

through lighting switch terminal 12

to fog lamp switch terminal 32.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 1ST or 2ND position
for front fog lamp operation.
With the fog lamp switch in the FRONT FOG ON position or FRONT & REAR FOG ON position, power is sup-
plied

through fog lamp switch terminal 31

to front fog lamp relay terminal 2.
Ground is supplied

to front fog lamp relay terminal 1

through grounds E24 and E50.
The front fog lamp relay is energized and power is supplied

through front fog lamp relay terminal 5

to front fog lamp LH and RH terminal 1, and

to combination meter terminal 15.
Ground is supplied

to front fog lamp LH and RH terminal 2

through grounds E24 and E50,

to combination meter terminal 64

through grounds M27 and M70.
With power and ground supplied, the front fog lamps and FRONT FOG indicator illuminate.

FRONT FOG LAMP
LT-109
C
D
E
F
G
H
I
J
L
MA
B
LT

Wiring Diagram — F/FOG — EKS003DG
TKWA1535E

LT-110
FRONT FOG LAMP

Aiming Adjustment EKS003DH
1. Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2. Turn fog lamp switch ON.
3. Insert a phillips screwdriver into the access hole and engage the
tip of the screwdriver with the gear of the adjuster as shown at
left. The aiming adjuster can now be turned by turning the
screwdriver.
4. Adjust front fog lamps so that the top edge of the high intensity
zone is 100 mm (3.94 in) below the height of the fog lamp cen-
ters as shown at left.

When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
PKIB1672E
PKIA5558E
PKIB1673E

FRONT FOG LAMP
LT-111
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 111 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Installation is the reverse order of removal.
CAUTION:

Never touch the glass of bulb directly by hand. Keep grease
and other oily matters away from it. Never touch bulb by
hand while it is lit or right after being turned off. Burning
may result.

Never leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION
Installation is the reverse order of removal.Front fog lamp : 12V - 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
: 5.5 N·m (0.56 kg-m, 49 in-lb)

LT-112
REAR FOG LAMP

REAR FOG LAMPPFP:26550
System Description EKS00ESB
DESCRIPTION
Power is supplied at all times (without front fog lamp)

through 15A fuse (No. 41, located in fuse and fusible link box)

to lighting switch terminal 5,

through 10A fuse (No. 36, located in fuse and fusible link box)

to rear fog lamp relay terminal 3.
Power is supplied at all times (with front fog lamp)

through 10A fuse (No. 31, located in the fuse and fusible link box)

to lighting switch terminal 11,

through 10A fuse (No. 36, located in fuse and fusible link box)

to rear fog lamp relay terminal 3.
With the lighting switch in the 2ND position, power is supplied (without front fog lamp)

through lighting switch terminal 25

to fog lamp switch terminal 34.
With the lighting switch in the 2ND position, power is supplied (with front fog lamp)

through lighting switch terminal 12

to fog lamp switch terminal 32.
FOG LAMP OPERATION
The front and rear fog lamp switch is built into the combination switch. The lighting switch must be in the 1ST
or 2ND position for rear fog lamp operation.
With the fog lamp switch in the REAR FOG ON position, ground is supplied

through fog lamp switch terminal 33

to rear fog lamp relay terminal 2.
Ground is supplied

to rear fog lamp relay terminal 1

through grounds E24 and E50.
The rear fog lamp relay is energized and power is supplied

through rear fog lamp relay terminal 5

to rear fog lamp terminal 1, and

to combination meter terminal 13.
Ground is supplied

to rear fog lamp terminal 2

through grounds B8 and B18,

to combination meter terminal 64

through grounds M27 and M70.
With power and ground supplied, the rear fog lamps and REAR FOG indicator illuminate.

REAR FOG LAMP
LT-113
C
D
E
F
G
H
I
J
L
MA
B
LT

Wiring Diagram — R/FOG —/Without Front Fog LampEKS003BV
TKWA1536E

LT-114
REAR FOG LAMP

Wiring Diagram — R/FOG —/With Front Fog LampEKS003BW
TKWA1537E