RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work Owners Manual

LOWER STRUCTURE
Rear floor, rear section (part section)
41M
CAA11538-1R6
M
13 1
CAA11538-1R6
N
14 1
41-49

LOWER STRUCTURE
Rear floor, rear section (part section)
41M
13348R1
INTRODUCTION
Below you will find special details for vehicles fit-
ted with a rear floor, front section .
CAT13329R1
O
1
8 11
1
12
2 1
41-50

LOWER STRUCTURE
Rear floor front cross member, front section
41N
PRB4134
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the sill panel clo-
sure panel for a side impact.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
This part may be replaced partially (see diagram
and method below).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Rear floor
Sill panel closure panel, front section
Sill panel closure panel, rear section
PARTS CONCERNED (thickness in mm):
1Rear floor front cross member,
front section 0.8
2Rear floor 1
3Sill panel closure panel, front section 1.2
4Sill panel closure panel, rear section 1.5
or
41-51

LOWER STRUCTURE
Rear floor front cross member, front section
41N
13232R1
or
CAA11538-2aR3
A
2 4
CAA11538R7
B
2
1
CAS13033R1
C
12
1
22
1
41-52

LOWER STRUCTURE
Rear floor stiffener
41O
PRB4135
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear floor for
a rear impact.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Rear floor
Rear side member
PARTS CONCERNED (thickness in mm):
1Rear floor stiffener 1
2Rear floor 0.8
3Rear side member 1.5
41-53

LOWER STRUCTURE
Rear floor stiffener
41O
13221R
CAA11538-2aR4
A
13
1 2
1
2
CAF11547-2R2
B
12 3
CAA11538R5
C
1 2
41-54

LOWER STRUCTURE
Rear end cross member
41P
PRB4136
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear end pa-
nel for a rear impact.
The side member extensions must be replaced
(11) and (12) , and must be ordered separately.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
10 - Part assembled with rear shock absorber
reinforcement
11 and 12 - Side member extension
JOINTS WITH:
Rear shock absorber reinforcement
Towing ring (left hand side)
Rear side member extension
Side panel rain channel
Side panel lining
Rear floor
Side member
PARTS CONCERNED (thickness in mm):
1Rear end cross member 1.2
2Rear shock absorber reinforcement 1
3Towing ring (left hand side) 1.5
4Rear side member extension 1.5
5Side panel rain channel 1.5
6Side panel lining 0.7
7Rear floor 0.8
8Side member 1.5
41-55

LOWER STRUCTURE
Rear end cross member
41P
13225R
CAB11539R7
A
1 6
CAB11539R7
B
1
6
CAA11536-1R3
C
1 6
CAT13327R3
D
1 3
1
2
1
2
2
41-56

LOWER STRUCTURE
Rear end cross member
41P
13221R1
CAT13327R5
E
12
1
2
CAT13328R1
F
31
CAA11538R5
G
1 7
CAH11549-1R1
H
87 1 4
1
2
4
41-57

LOWER STRUCTURE
Rear shock absorber reinforcement
41Q
PRB4137
INTRODUCTION
For a rear impact, the replacement of this part is a
complementary operation to the replacement of
the rear end panel.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Rear shock absorber reinforcement
Rear end cross member
PARTS CONCERNED (thickness in mm):
1Rear shock absorber reinforcement 1
2Rear end cross member 1.2
3Towing ring (left hand side) 1.5
4Rear side member extension 1.5
41-58