check oil SSANGYONG MUSSO 1998 Workshop Manual PDF

M161 ENGINE CONTROLS 1F2-21
Failure
codeItem
Checking method Test
stepRequirement
Specified
valuePossible cause
Þ 5.1· ·· ·
· Crankshaft
position
sensor:
- Resistance· Ignition:OFF
- Disconnect the
coupling “No.2”
from ECU (engine
side coupling).· Cable
· Crankshaft position
sensor Þ 5.0
· Engine:in cranking
99 100Measure the
signal (refer to
figure 6)· ·· ·
· Crankshaft
position
sensor:
- Signal17,
18,
20,
67,· Increament failure
in driven plate
· Þ 5.1
> 5 V - 99 100
99 100
1050 - 1400W
Þ 6.0
· Engine:in cranking
104 106· Þ 6.1
· Cable
· Camshaft position
sensor Measure the
signal(refer to
figure 8)
· ·· ·
· Camshaft
position
sensor:
(E23 only)
- Signal
Þ 4.0· Ignition:ON
69 7111 -14 V· ·· ·
· Ignition
coil(T1/2)
- No.2,3
Cylinder65,· Cable
· Ignition coil(T1/2)
· Fuse No.17
· Engine:in cranking > 10 V
· Engine:idling
- Voltage
(alternating)
· Engine:in cranking
· Engine:idling> 2.5 V -
19,
58,
106 11The value will
be changed in
1.2 - 1.7 V. - Voltage
(alternating)
· Engine:in cranking
Þ 6.1
· Ignition:ON
- Remove the
connector from the
camshaft position
sensor 1311 -14 V· ·· ·
· Camshaft
position
sensor
(E23 only)
- Power supply· Cable
· OVPR
Camshaft position
sensor

1F2-22 M161 ENGINE CONTROLS
Failure
codeItem
Checking method Test
stepRequirement
Specified
valuePossible cause
0.9 - 1.6 W 72 11
72 71
· ·· ·
· Ignition
coil(T1/1)
- Primary coil
voltage
(No.1 , 4
cylinder)· Engine:in cranking
(starter operating)
- Measuring range:
400 V
- Time range: 100 %
(using engine tester)
· Ignition:OFF200 - 350 V
64,Þ 7.0· Þ 7.1
Þ 7.1
· ·· ·
· Connection
ignition coil
between T1/
1 and T1/2· Cable
· Ignition coil T1/1
· Ignition coil T1/2
71 11
· ·· ·
· Ignition
coil(T1/2)
- Primary coil
voltage
(No.2 , 3
cylinder)· Engine:in cranking
(starter operating)
- Measuring range:
400 V
- Time range: 100 %
(using engine tester)200 - 350 V 65,Þ 8.0· Þ 8.1
0.9 - 1.6 W
71 72
· Ignition:OFFÞ 8.1· ·· ·
· Connection
ignition coil
between T1/
1 and T1/2· Cable
· Ignition coil T1/1
· Ignition coil T1/2 The
resistance of
ignition coil at
20°C is
approached
0.6W. The
resistance of
ignition coil at
20°C is
approached
0.6W.
8 - 20 KV
· ·· ·
· Ignition coil
(T1/1, T1/2)
- Secondary
ignition
voltage· Engine:in cranking
- Select the ignition
coil in order of T1/1,
T1/2
- Measuring range :
20KV
- Time range : 100%Þ 9.0 64,
65,Engine tester· Þ 9.1
· Ignition plug
· ECU
· High tension cable

M161 ENGINE CONTROLS 1F2-23
Failure
codeItem
Checking method Test
stepRequirement
Specified
valuePossible cause
> 10 MW
11 7 11 8· Ignition:OFF
- Disconnect the
coupling "No.2"
from ECU.Þ 10.1· ·· ·
· Knock
sensor
- Resistance· Connecting
condition
· Cable
· ECU 6 - 8.5 KW
· ·· ·
· Ignition coil
(T1/1, T1/2)
- Secondary
coil
resistance· Remove the high
tension cable of
T1/1, T1/2 Þ 9.1Ignition coil
(T1/1, T1/2)· Ignition coil T1/1
· Ignition coil T1/2
TM.4a
TM.4b
56,

1F2-46 M161 ENGINE CONTROLS
3. Disconnect the vacuum hose.
4. Disconnect the circlip and remove the fuel pressure
regulator.
5. Apply the oil to O-ring lightly and then replace it.
6. Installation should follow the removal procedure in the
reverse order.
7. Check for fuel pressure and internal leaks by operating the
engine. 2. Discharge the pressure in fuel supply system by pressing
the service valve.
Removal & Installation Procedure
1. Remove the fuel pressure test connector.

1F2-50 M161 ENGINE CONTROLS
Tightening Torque
22.5 - 27.5 Nm
Tightening Torque22.5 - 27.5 Nm
Removal & Installation Procedure
1. Discharge the fuel pressure from the fuel pressure test
connector by pushing service valve (arrow).
2. Disconnect the battery ground cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Disconnect the cable from ignition coil.
5. Remove the fuel return and supply line.
Installation Notice
Notice
lFor removal, cover around parts with cloths not to
bestained by fuel.
lIn case of checking the injector only, do not remove the
fuel return and supply line.
6. Remove the four injector connectors (arrows).
7. Unscrew the two combination bolts (8).
Installation Notice

M161 ENGINE CONTROLS 1F2-51
9. Installation should follow the removal procedure in the
reverse order.
10. Check for fuel pressure and internal leakage by operating
the engine. 8. Pull out the injector from intake manifold and remove the
fuel distributor.
Notice
Replace the injector O-ring with new one.
Ignition Coil & Cable
lIgnition coil T1/1 No.1 cylinder + No.4 cylinder
lInition coil T1/2 No.1 cylinder + No.4 cylinder

M161 ENGINE CONTROLS 1F2-55
Removal & Installation Procedure
1. Remove the O-ring.
Check for damage and replace it if necessary.
2. Remove the injector bracket from the injector.
Installation Notice
Exactly seat the anti-twist lock into the square groove in
injector.
3. Separate the injector from the fuel distributor.
Inspection & Maintenance
Inspection of the Injector operation and spray pattern
1. Connect the contact box to the ECU.
2. Connect the shop made test plug to the injector and place
it into the tank.
3. Position the ignition switch to ON.
4. Connect the pin 63(+) and 69(-) of the contact box with a
test cable.
5. Check the injector spray pattern.
Notice
Replace the injector if the injector spray pattern is abnormal
or the fuel doesn't inject.
Injector Resistance Inspection
1. Remove the injector connector.
2. Measure the injector coil resistance using a resistance
tester.
Notice
Replace the injector if the measured values is out of the
specified values. Check the connector and wire connection
between the ECU and the injector if the measured values
are normal.
Specified Value
14 - 17 W

1F3-30 OM600 ENGINE CONTROLS
REMOVAL AND INSTALLATION OF INJECTION TIMING DEVICE
Preceding Work : Removal of vacuum pump
1 Cylinder Head Cover
2 Bolt............................................................10Nm
3 Gasket ................................................... Replace
4 Fuel Injection Pump
5 Seal....................................................... Replace
6 Screw Plug.................................................30Nm
7 Oil Pan
8 Locking Pin
9 Injection Timing Device10 Washer
11 Bolt (Left-Hand Thread).............................46Nm
12 Camshaft Sprocket
13 Washer
14 12-Sided Stretch Bolt............Check, 25Nm + 90°
15 Timing Chain
1 6 Seal
17 Chain Tensioner.........................................80Nm

1F3-38 OM600 ENGINE CONTROLS
Tools Required
617 589 08 21 00 Position Sensor
Test Procedure
1. Remove the screw plug (5) and seal (4) and collect oil in a
suitable vessel.
2. Install the position sensor (1) into the governor housing of
the injection pump to be the guide pin of the position sensor
facing up.
3. Connect the battery terminal of position sensor (1) to positive
terminal (+) of battery.
Position Sensor 617 589 08 21 00
4. Rotate the crankshaft by hand (in direction of engine rotation)
until the lamp ‘B’ lights up. Rotate the crankshaft carefully
further until both lamps ‘A and B’ come on. In this position,
check the Rl value on the crankshaft vibration damper.
Notice
If only lamp ‘A’ lights up, repeat the test and if out of
specification, adjust start of delivery.
Specification ATDC 14° - 16°

OM600 ENGINE CONTROLS 1F3-41
With Pulse Generator Tools Required
617 589 09 21 00 Rl Sensor
617 589 10 21 00 Timing Tester
667 589 00 21 00 TDC Pulse Generator
Commercial Tools
Item
Digital Tester
Without Pulse GeneratorTools
Bosch, MOT 001.03
Hartmann & Braun, EOMT3
Bosch, ETD 019.00
Sun, DIT 9000
ALV, Diesel - Tester 875
Test Procedure
1. Remove the screw plug (7) and seal (8) collect oil in a suitable
vessel.
2. Install the Rl sensor into the governor housing of injection
pump (1).
Rl Sensor 617 589 10 21 00
3. Connect the digital tester and TDC pulse sender unit
according to connection diagram.
4. Run the engine at idle speed and check the Rl value on the
digital tester
Notice
If out of standard, adjust the start of delivery.
5. Stop the engine.
6. Remove the Rl sensor, digital tester and TDC pulse sender
unit.
7. Replace the seal and tighten the plug.
8. Check engine oil level and adjust if necessary.
Rl value ATDC 14° - 16°
Tightening Torque 30 Nm