sensor SUBARU TRIBECA 2009 1.G Service Workshop Manual

FU(H6DO)-31
Rear Oxygen Sensor
FUEL INJECTION (FUEL SYSTEMS)
4) Connect the connector to rear oxygen sensor.
•LH side
•RH side
5) Lower the vehicle.
6) Connect the battery ground cable to the battery.
FU-02143
FU-02144

FU(H6DO)-38
Fuel Tank
FUEL INJECTION (FUEL SYSTEMS)
22.Fuel Tank
A: REMOVAL
WARNING:
•Place “NO FIRE” signs near the working area.
•Be careful not to spill fuel on the floor.
1) Set the vehicle on a lift.
2) Release the fuel pressure. <Ref. to FU(H6DO)-
37, RELEASING OF FUEL PRESSURE, PROCE-
DURE, Fuel.>
3) Disconnect the ground cable from battery.
4) Drain fuel from fuel tank.
<Ref. to FU(H6DO)-37, DRAINING FUEL, PRO-
CEDURE, Fuel.>
5) Remove the second seat. <Ref. to SE-12, RE-
MOVAL, Second-row Seats.>
6) Remove the service hole cover of fuel pump.
(1) Disconnect the connector.
(2) Remove the bolt.
(3) Push the grommet down and remove ser-
vice hole cover.
7) Remove the service hole cover of fuel sub level
sensor.
8) Disconnect the quick connector on the fuel deliv-
ery hose. <Ref. to FU(H6DO)-48, REMOVAL, Fuel
Delivery, Return and Evaporation Lines.>
9) Remove the rear wheels.
10) Lift-up the vehicle.
11) Remove the clip holding the harness.
12) Remove the rear suspension assembly. <Ref.
to RS-16, REMOVAL, Rear Sub Frame.>
13) Disconnect the following hoses and connec-
tors.
(1) Evaporation hose
(2) Fuel filler hose
(3) Connector
(A) Bolt
(B) Grommet
(C) Connector
FU-02661(A)
(A)
(B)(C)
FU-02662
(A) Evaporation hose
(B) Connector
(C) Fuel filler hose
FU-02663
FU-02664
FU-02665
(A)
(B)
(C)

FU(H6DO)-39
Fuel Tank
FUEL INJECTION (FUEL SYSTEMS)
14) Remove the fuel tank from the vehicle.
WARNING:
A helper is required to perform this work.
(1) Support the fuel tank with the transmission
jack.
(2) Remove the fuel tank band that holds the
fuel tank.
(3) Remove the fuel tank from the vehicle.
B: INSTALLATION
1) Install the fuel tank to the vehicle.
WARNING:
A helper is required to perform this work.
(1) Lift the fuel tank with the transmission jack.
(2) Mount the fuel tank to the vehicle with a jack.
(3) Install the fuel tank band that holds the fuel
tank.
Tightening torque:
33 N·m (3.4 kgf-m, 25 ft-lb)
2) Connect the following hoses and connectors.
(1) Evaporation hose
(2) Fuel filler hose
(3) Connector
3) Install the rear suspension assembly. <Ref. to
RS-16, INSTALLATION, Rear Sub Frame.>
4) Install the clip that holds the harness.
5) Lower the vehicle.
6) Install the rear wheels.
7) Connect the quick connector on fuel delivery
hose. <Ref. to FU(H6DO)-49, INSTALLATION,
Fuel Delivery, Return and Evaporation Lines.>
8) Install the service hole cover of fuel sub level
sensor.
FU-02666
FU-02666
(A) Evaporation hose
(B) Connector
(C) Fuel filler hose
FU-02665
(A)
(B)
(C)
FU-02664
FU-02662

FU(H6DO)-43
Fuel Pump
FUEL INJECTION (FUEL SYSTEMS)
24.Fuel Pump
A: REMOVAL
WARNING:
•Place “NO FIRE” signs near the working area.
•Be careful not to spill fuel on the floor.
NOTE:
Fuel pump assembly consists of fuel pump and fuel
level sensor.
1) Release the fuel pressure. <Ref. to FU(H6DO)-
37, RELEASING OF FUEL PRESSURE, PROCE-
DURE, Fuel.>
2) Drain fuel. <Ref. to FU(H6DO)-37, DRAINING
FUEL, PROCEDURE, Fuel.>
3) Remove the second seat. <Ref. to SE-12, RE-
MOVAL, Second-row Seats.>
4) Remove the service hole cover.
5) Disconnect the connector from fuel pump.
6) Disconnect the quick connector, and then dis-
connect the fuel delivery hose, return hose and jet
pump hose. <Ref. to FU(H6DO)-48, REMOVAL,
Fuel Delivery, Return and Evaporation Lines.>
7) Remove the nuts which install fuel pump assem-
bly onto fuel tank.
8) Remove the fuel pump assembly from the fuel
tank.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Use a new gasket.
1. Make sure the sealing portion is free from fuel or
foreign matter before installation.
2. Tighten the nuts to the specified torque in the or-
der as shown in the figure.
Tightening torque:
4.4 N·m (0.45 kgf-m, 3.2 ft-lb)
FU-02681
FU-02669
(A) Delivery hose
(B) Jet pump hose
FU-02670(A)
(B)
FU-01141
1
2
3
4
56
7
8

FU(H6DO)-45
Fuel Level Sensor
FUEL INJECTION (FUEL SYSTEMS)
25.Fuel Level Sensor
A: REMOVAL
WARNING:
•Place “NO FIRE” signs near the working area.
•Be careful not to spill fuel on the floor.
NOTE:
The fuel level sensor is built in fuel pump assembly.
1) Remove the fuel pump assembly. <Ref. to
FU(H6DO)-43, REMOVAL, Fuel Pump.>
2) Disconnect the connector from fuel pump brack-
et.
3) Remove the fuel temperature sensor.
4) Remove the fuel level sensor.
B: INSTALLATION
Install in the reverse order of removal.
(A) Connector
(B) Fuel temperature sensor
(C) Fuel level sensor

FU(H6DO)-46
Fuel Sub Level Sensor
FUEL INJECTION (FUEL SYSTEMS)
26.Fuel Sub Level Sensor
A: REMOVAL
WARNING:
•Place “NO FIRE” signs near the working area.
•Be careful not to spill fuel on the floor.
1) Drain fuel. <Ref. to FU(H6DO)-37, DRAINING
FUEL, PROCEDURE, Fuel.>
2) Remove the second seat. <Ref. to SE-12, RE-
MOVAL, Second-row Seats.>
3) Remove the service hole cover.
4) Disconnect the connector from the fuel sub level
sensor.
5) Disconnect the quick connector, and then dis-
connect the fuel delivery hose, return hose and jet
pump hose. <Ref. to FU(H6DO)-48, REMOVAL,
Fuel Delivery, Return and Evaporation Lines.>
6) Remove the nuts and bolts which install fuel sub
level sensor on fuel tank.
7) Remove the fuel sub level sensor.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Use a new gasket.
1. Make sure the sealing portion is free from fuel or
foreign matter before installation.
2. Tighten the nuts and bolts to the specified
torque in the order as shown in the figure.
Tightening torque:
4.4 N·m (0.45 kgf-m, 3.2 ft-lb)
(A) Jet pump hose
(B) Delivery hose
FU-02662
FU-02672
FU-02673(B)
(A)
FU-01145
1
6
5
2
4
3
FU-02674

FU(H6DO)-51
Fuel System Trouble in General
FUEL INJECTION (FUEL SYSTEMS)
29.Fuel System Trouble in General
A: INSPECTION
NOTE:
•When the vehicle is left unattended for an extended period of time, water may accumulate in the fuel tank.
Fill fuel fully to prevent those problem. And also drain water from fuel filter.
•In snow-covered areas, mountainous areas, skiing areas, etc. where ambient temperatures drop below
0°C (32°F) throughout the winter season, use a water removing agent in the fuel system to prevent freezing
fuel system and accumulating water. Fill the water removing agent at the time when the fuel reduced at half
to maintain the advantage.
•When water is accumulated in fuel filter, drain water from both the fuel filter and fuel tank or use water re-
moving agent in the fuel tank.
•Before using water removing agent, follow the cautions noted on the bottle.
Tr o u b l e a n d p o s s i b l e c a u s e C o r r e c t i v e a c t i o n
1. Insufficient fuel supply to injector
1) Fuel pump does not operate.
Defective terminal contactInspect contact, especially ground, and tighten it
securely.
Tr o u b l e i n e l e c t r o m a g n e t i c o r e l e c t r o n i c c i r c u i t p a r t s R e p l a c e t h e f a u l t y p a r t s .
2) Decline of fuel pump function Replace the fuel pump.
3) Clogged dust or water in the fuel filter Replace the fuel pump and clean or replace the fuel tank.
4) Clogged or bent fuel pipe or hose Clean, correct or replace the fuel pipe or hose.
5) Air is mixed in fuel system. Inspect or retighten each connection part.
6) Clogged or bent air breather hose or pipe Clean, correct or replace the air breather hose or pipe.
7) Damaged diaphragm of pressure regulator Replace the fuel pump.
2. Leakage or blow out of fuel
1) Loose joints of the fuel pipe Retighten.
2) Cracked fuel pipe, hose and fuel tank Replace.
3) Defective welding part on the fuel tank Replace.
4) Defective drain packing of the fuel tank Replace.
5) Clogged or bent air breather hose or air vent tubeClean, correct or replace the air breather hose or air vent
tube.
3. Gasoline smell inside of compartment
1)Loose joints at air breather hose, air vent tube and fuel filler
pipeRetighten.
2) Defective packing air tightness on the fuel saucer Correct or replace the packing.
3) Inoperative fuel pump modulator or circuit Replace.
4. Defective fuel meter indicator
1) Defective operation of fuel level sensor Replace.
2) Defective operation of fuel meter Replace.
5. Noise
1) Large operation noise or vibration of fuel pump Replace.

GD(H6DO)-2
List of Diagnostic Trouble Code (DTC)
GENERAL DESCRIPTION
1. List of Diagnostic Trouble Code (DTC)
A: LIST
DTC Item Index
P0011 Intake Camshaft Position Timing -
Over-Advanced (Bank 1)
<Ref. to GD(H6DO)-9, DTC P0011 INTAKE CAMSHAFT POSITION TIMING
- OVER-ADVANCED (BANK 1), Diagnostic Trouble Code (DTC) Detecting
Criteria.>
P0016 Crankshaft Position - Camshaft
Pos it i o n C o r r el a ti o n ( B a nk 1)
<Ref. to GD(H6DO)-11, DTC P0016 CRANKSHAFT POSITION - CAM-
SHAFT POSITION CORRELATION (BANK 1), Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0018 Crankshaft Position - Camshaft
Pos it i o n C o r r el a ti o n ( B a nk 2)
<Ref. to GD(H6DO)-11, DTC P0018 CRANKSHAFT POSITION - CAM-
SHAFT POSITION CORRELATION (BANK 2), Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0021 Intake Camshaft Position Timing -
Over-Advanced (Bank 2)
<Ref. to GD(H6DO)-11, DTC P0021 INTAKE CAMSHAFT POSITION TIM-
ING - OVER-ADVANCED (BANK 2), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0026 Intake Valve Control Solenoid Cir-
cuit Range/Performance (Bank 1)
<Ref. to GD(H6DO)-12, DTC P0026 INTAKE VALVE CONTROL SOLENOID
CIRCUIT RANGE/PERFORMANCE (BANK 1), Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0028 Intake Valve Control Solenoid Cir-
cuit Range/Performance (Bank 2)
<Ref. to GD(H6DO)-15, DTC P0028 INTAKE VALVE CONTROL SOLENOID
CIRCUIT RANGE/PERFORMANCE (BANK 2), Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0030 HO2S Heater Control Circuit (Bank
1 Sensor 1)
<Ref. to GD(H6DO)-15, DTC P0030 HO2S HEATER CONTROL CIRCUIT
(BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0031 HO2S Heater Control Circuit Low
(Bank 1 Sensor 1)
<Ref. to GD(H6DO)-17, DTC P0031 HO2S HEATER CONTROL CIRCUIT
LOW (BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0032 HO2S Heater Control Circuit High
(Bank 1 Sensor 1)
<Ref. to GD(H6DO)-19, DTC P0032 HO2S HEATER CONTROL CIRCUIT
HIGH (BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0037 HO2S Heater Control Circuit Low
(Bank 1 Sensor 2)
<Ref. to GD(H6DO)-21, DTC P0037 HO2S HEATER CONTROL CIRCUIT
LOW (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0038 HO2S Heater Control Circuit High
(Bank 1 Sensor 2)
<Ref. to GD(H6DO)-23, DTC P0038 HO2S HEATER CONTROL CIRCUIT
HIGH (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0050 HO2S Heater Control Circuit (Bank
2 Sensor 1)
<Ref. to GD(H6DO)-25, DTC P0050 HO2S HEATER CONTROL CIRCUIT
(BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0051 HO2S Heater Control Circuit Low
(Bank 2 Sensor 1)
<Ref. to GD(H6DO)-25, DTC P0051 HO2S HEATER CONTROL CIRCUIT
LOW (BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0052 HO2S Heater Control Circuit High
(Bank 2 Sensor 1)
<Ref. to GD(H6DO)-25, DTC P0052 HO2S HEATER CONTROL CIRCUIT
HIGH (BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0057 HO2S Heater Control Circuit Low
(Bank 2 Sensor 2)
<Ref. to GD(H6DO)-25, DTC P0057 HO2S HEATER CONTROL CIRCUIT
LOW (BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0058 HO2S Heater Control Circuit High
(Bank 2 Sensor 2)
<Ref. to GD(H6DO)-25, DTC P0058 HO2S HEATER CONTROL CIRCUIT
HIGH (BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0068 MAP/MAF - Throttle Position Cor-
relation
<Ref. to GD(H6DO)-26, DTC P0068 MAP/MAF - THROTTLE POSITION
CORRELATION, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0076 Intake Valve Control Circuit Low
(Bank 1)
<Ref. to GD(H6DO)-28, DTC P0076 INTAKE VALVE CONTROL CIRCUIT
LOW (BANK 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0077 Intake Valve Control Circuit High
(Bank 1)
<Ref. to GD(H6DO)-29, DTC P0077 INTAKE VALVE CONTROL CIRCUIT
HIGH (BANK 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0082 Intake Valve Control Circuit Low
(Bank 2)
<Ref. to GD(H6DO)-30, DTC P0082 INTAKE VALVE CONTROL CIRCUIT
LOW (BANK 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>

GD(H6DO)-3
List of Diagnostic Trouble Code (DTC)
GENERAL DESCRIPTION
P0083 Intake Valve Control Circuit High
(Bank 2)
<Ref. to GD(H6DO)-30, DTC P0083 INTAKE VALVE CONTROL CIRCUIT
HIGH (BANK 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0101 Mass or Volume Air Flow Circuit
Range/Performance
<Ref. to GD(H6DO)-31, DTC P0101 MASS OR VOLUME AIR FLOW CIR-
CUIT RANGE/PERFORMANCE, Diagnostic Trouble Code (DTC) Detecting
Criteria.>
P0102 Mass or Volume Air Flow Circuit
Low Input
<Ref. to GD(H6DO)-34, DTC P0102 MASS OR VOLUME AIR FLOW CIR-
CUIT LOW INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0103 Mass or Volume Air Flow Circuit
High Input
<Ref. to GD(H6DO)-36, DTC P0103 MASS OR VOLUME AIR FLOW CIR-
CUIT HIGH INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0107 Manifold Absolute Pressure/Baro-
metric Pressure Circuit Low Input
<Ref. to GD(H6DO)-38, DTC P0107 MANIFOLD ABSOLUTE PRESSURE/
BAROMETRIC PRESSURE CIRCUIT LOW INPUT, Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0108 Manifold Absolute Pressure/Baro-
metric Pressure Circuit High Input
<Ref. to GD(H6DO)-40, DTC P0108 MANIFOLD ABSOLUTE PRESSURE/
BAROMETRIC PRESSURE CIRCUIT HIGH INPUT, Diagnostic Trouble
Code (DTC) Detecting Criteria.>
P0111 Intake Air Temperature Circuit
Range/Performance
<Ref. to GD(H6DO)-42, DTC P0111 INTAKE AIR TEMPERATURE CIRCUIT
RANGE/PERFORMANCE, Diagnostic Trouble Code (DTC) Detecting Crite-
ria.>
P0112 Intake Air Temperature Circuit Low
Input
<Ref. to GD(H6DO)-44, DTC P0112 INTAKE AIR TEMPERATURE CIRCUIT
LOW INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0113 Intake Air Temperature Circuit High
Input
<Ref. to GD(H6DO)-46, DTC P0113 INTAKE AIR TEMPERATURE CIRCUIT
HIGH INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0117 Engine Coolant Temperature Cir-
cuit Low Input
<Ref. to GD(H6DO)-48, DTC P0117 ENGINE COOLANT TEMPERATURE
CIRCUIT LOW INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0118 Engine Coolant Temperature Cir-
cuit High Input
<Ref. to GD(H6DO)-50, DTC P0118 ENGINE COOLANT TEMPERATURE
CIRCUIT HIGH INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0122 Throttle/Pedal Position Sensor/
Switch “A” Circuit Low Input
<Ref. to GD(H6DO)-52, DTC P0122 THROTTLE/PEDAL POSITION SEN-
SOR/SWITCH “A” CIRCUIT LOW INPUT, Diagnostic Trouble Code (DTC)
Detecting Criteria.>
P0123 Throttle/Pedal Position Sensor/
Switch “A” Circuit High Input
<Ref. to GD(H6DO)-54, DTC P0123 THROTTLE/PEDAL POSITION SEN-
SOR/SWITCH “A” CIRCUIT HIGH INPUT, Diagnostic Trouble Code (DTC)
Detecting Criteria.>
P0125 Insufficient Coolant Temperature
For Closed Loop Fuel Control
<Ref. to GD(H6DO)-56, DTC P0125 INSUFFICIENT COOLANT TEMPERA-
TURE FOR CLOSED LOOP FUEL CONTROL, Diagnostic Trouble Code
(DTC) Detecting Criteria.>
P0126 Insufficient Coolant Temperature
for Stable Operation
<Ref. to GD(H6DO)-58, DTC P0126 INSUFFICIENT COOLANT TEMPERA-
TURE FOR STABLE OPERATION, Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0128 Coolant Thermostat (Coolant Tem-
perature Below Thermostat Regu-
lating Temperature)
<Ref. to GD(H6DO)-60, DTC P0128 COOLANT THERMOSTAT (COOLANT
TEMPERATURE BELOW THERMOSTAT REGULATING TEMPERATURE),
Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0131 O2 Sensor Circuit Low Voltage
(Bank 1 Sensor 1)
<Ref. to GD(H6DO)-62, DTC P0131 O2 SENSOR CIRCUIT LOW VOLTAGE
(BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0132 O2 Sensor Circuit High Voltage
(Bank 1 Sensor 1)
<Ref. to GD(H6DO)-64, DTC P0132 O2 SENSOR CIRCUIT HIGH VOLTAGE
(BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0133 O2 Sensor Circuit Slow Response
(Bank 1 Sensor 1)
<Ref. to GD(H6DO)-66, DTC P0133 O2 SENSOR CIRCUIT SLOW
RESPONSE (BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0134 O2 Sensor Circuit No Activity
Detected (Bank 1 Sensor 1)
<Ref. to GD(H6DO)-69, DTC P0134 O2 SENSOR CIRCUIT NO ACTIVITY
DETECTED (BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0137 O2 Sensor Circuit Low Voltage
(Bank 1 Sensor 2)
<Ref. to GD(H6DO)-71, DTC P0137 O2 SENSOR CIRCUIT LOW VOLTAGE
(BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0138 O2 Sensor Circuit High Voltage
(Bank 1 Sensor 2)
<Ref. to GD(H6DO)-74, DTC P0138 O2 SENSOR CIRCUIT HIGH VOLTAGE
(BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>
DTC Item Index

GD(H6DO)-4
List of Diagnostic Trouble Code (DTC)
GENERAL DESCRIPTION
P0139 O2 Sensor Circuit Slow Response
(Bank 1 Sensor 2)
<Ref. to GD(H6DO)-75, DTC P0139 O2 SENSOR CIRCUIT SLOW
RESPONSE (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0140 O2 Sensor Circuit No Activity
Detected (Bank 1 Sensor 2)
<Ref. to GD(H6DO)-80, DTC P0140 O2 SENSOR CIRCUIT NO ACTIVITY
DETECTED (BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0151 O2 Sensor Circuit Low Voltage
(Bank 2 Sensor 1)
<Ref. to GD(H6DO)-81, DTC P0151 O2 SENSOR CIRCUIT LOW VOLTAGE
(BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0152 O2 Sensor Circuit High Voltage
(Bank 2 Sensor 1)
<Ref. to GD(H6DO)-81, DTC P0152 O2 SENSOR CIRCUIT HIGH VOLTAGE
(BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0153 O2 Sensor Circuit Slow Response
(Bank 2 Sensor 1)
<Ref. to GD(H6DO)-81, DTC P0153 O2 SENSOR CIRCUIT SLOW
RESPONSE (BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0154 O2 Sensor Circuit No Activity
Detected (Bank 2 Sensor 1)
<Ref. to GD(H6DO)-82, DTC P0154 O2 SENSOR CIRCUIT NO ACTIVITY
DETECTED (BANK 2 SENSOR 1), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0157 O2 Sensor Circuit Low Voltage
(Bank 2 Sensor 2)
<Ref. to GD(H6DO)-82, DTC P0157 O2 SENSOR CIRCUIT LOW VOLTAGE
(BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0158 O2 Sensor Circuit High Voltage
(Bank 2 Sensor 2)
<Ref. to GD(H6DO)-82, DTC P0158 O2 SENSOR CIRCUIT HIGH VOLTAGE
(BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0159 O2 Sensor Circuit Slow Response
(Bank 2 Sensor 2)
<Ref. to GD(H6DO)-82, DTC P0159 O2 SENSOR CIRCUIT SLOW
RESPONSE (BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0160 O2 Sensor Circuit No Activity
Detected (Bank 2 Sensor 2)
<Ref. to GD(H6DO)-82, DTC P0160 O2 SENSOR CIRCUIT NO ACTIVITY
DETECTED (BANK 2 SENSOR 2), Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0171 System Too Lean (Bank 1) <Ref. to GD(H6DO)-83, DTC P0171 SYSTEM TOO LEAN (BANK 1), Diag-
nostic Trouble Code (DTC) Detecting Criteria.>
P0172 System Too Rich (Bank 1) <Ref. to GD(H6DO)-85, DTC P0172 SYSTEM TOO RICH (BANK 1), Diag-
nostic Trouble Code (DTC) Detecting Criteria.>
P0174 System Too Lean (Bank 2) <Ref. to GD(H6DO)-86, DTC P0174 SYSTEM TOO LEAN (BANK 2), Diag-
nostic Trouble Code (DTC) Detecting Criteria.>
P0175 System Too Rich (Bank 2) <Ref. to GD(H6DO)-86, DTC P0175 SYSTEM TOO RICH (BANK 2), Diag-
nostic Trouble Code (DTC) Detecting Criteria.>
P0181 Fuel Temperature Sensor “A” Cir-
cuit Range/Performance
<Ref. to GD(H6DO)-87, DTC P0181 FUEL TEMPERATURE SENSOR “A”
CIRCUIT RANGE/PERFORMANCE, Diagnostic Trouble Code (DTC) Detect-
ing Criteria.>
P0182 Fuel Temperature Sensor “A” Cir-
cuit Low Input
<Ref. to GD(H6DO)-90, DTC P0182 FUEL TEMPERATURE SENSOR “A”
CIRCUIT LOW INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0183 Fuel Temperature Sensor “A” Cir-
cuit High Input
<Ref. to GD(H6DO)-92, DTC P0183 FUEL TEMPERATURE SENSOR “A”
CIRCUIT HIGH INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0196 Engine Oil Temperature Sensor
Circuit Range/Performance
<Ref. to GD(H6DO)-94, DTC P0196 ENGINE OIL TEMPERATURE SEN-
SOR CIRCUIT RANGE/PERFORMANCE, Diagnostic Trouble Code (DTC)
Detecting Criteria.>
P0197 Engine Oil Temperature Sensor
Circuit Low
<Ref. to GD(H6DO)-96, DTC P0197 ENGINE OIL TEMPERATURE SEN-
SOR CIRCUIT LOW, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0198 Engine Oil Temperature Sensor
Circuit High
<Ref. to GD(H6DO)-97, DTC P0198 ENGINE OIL TEMPERATURE SEN-
SOR CIRCUIT HIGH, Diagnostic Trouble Code (DTC) Detecting Criteria.>
P0222 Throttle/Pedal Position Sensor/
Switch “B” Circuit Low Input
<Ref. to GD(H6DO)-98, DTC P0222 THROTTLE/PEDAL POSITION SEN-
SOR/SWITCH “B” CIRCUIT LOW INPUT, Diagnostic Trouble Code (DTC)
Detecting Criteria.>
P0223 Throttle/Pedal Position Sensor/
Switch “B” Circuit High Input
<Ref. to GD(H6DO)-100, DTC P0223 THROTTLE/PEDAL POSITION SEN-
SOR/SWITCH “B” CIRCUIT HIGH INPUT, Diagnostic Trouble Code (DTC)
Detecting Criteria.>
P0230 Fuel Pump Primary Circuit <Ref. to GD(H6DO)-102, DTC P0230 FUEL PUMP PRIMARY CIRCUIT,
Diagnostic Trouble Code (DTC) Detecting Criteria.>
DTC Item Index