clutch CITROEN BERLINGO FIRST 2011 Handbook (in English)

11-
SPEED LIMITER * CRUISE CONTROL *




65



63 If the vehicle is fi tted with
a speed limiter and cruise
control, these functions can-
not both be activated at the
same time. This limiter indicates the status of
selection of the function on the in-
strument panel and displays the
programmed speed. The minimum
speed which can be programmed is
at least 18 mph (30 km/h).
It prevents exceeding of the speed
programmed by the driver, this func-
tion remains active regardless of any
action on the brake or clutch pedals.
On the other hand, pressing the ac-
celerator pedal to the point of resist-
ance does not have any effect.
It is possible to exceed the pro-
grammed speed temporarily by
pressing the accelerator fi rmly be-
yond this point of resistance.
The operating actions must be car-
ried out with the engine running. The cruise control has a display on
the instrument panel to indicate the
programmed reference speed.
It enables the vehicle to maintain the
reference speed programmed by the
driver.
In order for it to be programmed or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with
at least fourth gear engaged.

* According to version.

DRIVING66 -
When changing the pro-
grammed reference speed
by means of a maintained
press, pay attention as the
speed can increase or de-
crease rapidly.
Do not use the cruise control on slip-
pery roads or in heavy traffi c.
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to observe the
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
It is advisable to leave your feet near
the pedals.
To prevent the mat from becoming
trapped under the pedals:


- ensure that the mat and its fi xings
are positioned correctly,

-
never fi t one mat on top of another.




Deactivation (off)


)
Press this button or the brake or
clutch pedal.


Changing the programmed
reference speed
When the speed is displayed:


)
press SET +
button to increase it.

)

press the SET -
button to decrease it.



Reactivation


)
Following deactivation of the
cruise control, press this button.
Your vehicle will return to the last
programmed speed.
Alternatively, you can repeat the "fi rst
activation" procedure.
Switching the function off


)
Place the dial in position 0
or
switch off the ignition to switch
everything off.


Operating fault
In the event of a cruise control mal-
function, a message is displayed on
the multifunction display accompanied
by an audible signal.
The programmed speed is cleared and
the dashes fl ash for a few seconds.
Contact a CITROËN dealer to have
the system checked.
Cancelling the programmed
reference speed
When the vehicle becomes station-
ary, after switching off the ignition,
the system no longer memorises a
speed.

89 PRACTICAL INFORMATION
-


Fuse N°



Rating



Functions




1



10A

Pre-heater unit (Diesel) -
Brake and clutch switches - Reversing lamps.


2



15A

Fuel pump.


3



10A

ABS control unit.


4



10A

Engine control unit.


5



-

Not used.


6



15A

Front foglamps.


7



20A

Headlamp wash pump.


8



20A

Fan assembly relay -
Engine control unit.


9



15A

Left-hand dipped beam.


10



15A

Right-hand dipped beam.


11



10A

Left-hand main beam.


12



10A

Right-hand main beam.


13



15A

Horn.


14



10A

Front and rear screen wash pumps.


15



30A

Oxygen sensor - Air
fl ow sensor.


16



30A

Air pump relay.


17



30A

Front windscreen wiper.


18



40A

Air conditioning fan.


Engine compartment fusebox

To gain access to the box in the engine
compartment (next to the battery), unclip
the cover.
After carrying out work, close the
cover carefully to ensure its sealing.