lock GEELY MK 2008 Owner's Guide

Component ViewIgnition switch cylinder
Conical head bolt
snap ring
Upper and lower Steering
column panel
Ignition switch bracket
Ignition switch assembly
snap ring Steering column
Main shaft¡ôMain shaft bearing A/T lock cablePower Steering System-Steering Drive and Control Mechanism4-70Non-reusable parts

Power Steering System
-Steering Drive and Control Mechanism4-71Replacement1. Precaution (refer to the steering system precaution)
2. Confirm that the wheel stays at a straight line running status.
3. Unfix the storage battery cathode terminal.
4. Remove the airbag assembly.
Remove the two screws on both sides, and pull out the cable connector.
Note: When removing the airbag assembly, never pull the airbag cables.
Caution: When put down the airbag assembly, make sure its top surface stays upward.
Never disassemble the airbag assembly.Using
Socket5. Remove the steering wheel assembly.
(1)Unfix the connector.
(2)Remove the set bolts of the steering wheel.
(3)Make a fit mark on the steering wheel assembly and main shaft assembly.
(4)Remove the steering wheel with special tool.
6. Remove the top shells and bottoms shell of the steering column shield.
(1)Remove the three screws.
(2)Remove the top part and bottom part of the steering column
shield.
7. Remove clock spring.
8. Remove the left combination switch assembly.
Separate the connector and remove the left combination switch
assembly.
9. Remove the right combination switch assembly.
Separate the connector and remove the right combination switch
assembly.
10. Remove the splined tube cover.
11. Detach No. 2 steering countershaft(see right figure)
(1) Make a mark on the fit between slide splined tube and countershaft. (2) Loosen bolts A and B.
12. Remove the steering column pipe assembly.
(1) Remove the cable connector on the steering column pipe assembly. (2) Remove the 3 bolts and steering column assembly.Installation mark

Power Steering System-Steering Drive and Control Mechanism4-7213. Remove the No.2 steering countershaft assembly.
(1) Make a mark on the fit between main shaft and countershaft.
(2) Remove bolt and countershaft.
14. Remove the ignition switch bracket.
(1) Use the punch pin to make a mark on the 2 conical head bolt.
(2) Drill the 2 conical head bolts with the diameter of 3-4mm drill
bit.
(3) Remove the bolts and bracket for the ignition switch with the
thread die.
15. Remove fixing panel on the steering column.
16.Remove the ignition switch lock core assembly.
(1) Turn the ignition switch to "ACC" position.
(2) press the stop pin and pull the lock core out.
17. After checking or replacing the steering column pipe assembly, install all parts in a reverse order.
Note:
(1) After installing the ignition switch lock core, check the operation of the steering locking function: when
pulling out the key, the steering device is locked; when the key is inserted and turned to ACC position, the
steering device is unlocked.
(2) Tighten the 3 bolts.
(3) Make sure all cables are connected reliably.
(4) After adjusting the combination switch as well as the top shell and bottom shell of the steering pipe shield,
fasten the three screws connecting the combination switch and the steering column assembly.
(5) Tighten the set bolt between the universal joint fork and the steering gear assembly with a torque of
22~39N.m.
(6) Install dust cover and its press plate.
(7) When installing the steering wheel assembly, align the steering wheel assembly and the fit mark of the
steering main shaft assembly. Tighten the special quincunx bolt with a torque of 33~59N.m.
(8) Check the airbag. It is not allowed to use a airbag part removed from another vehicle.
(9) Check the SRS warning lamp.Thread die Installation mark

Steering rack end sub-assembly
Steering rack end sub-assembly
Left ball extension shaft Left ball extension shaftComponent ViewPower Steering System-Power Steering Gear4-76Lock nut
Steering rack # 1 dust shield
Clip
Hoop
O-ring Steering hydraulic
oil pipe
O-ring
Hoop
Clip O-ring
Steering rack # 2 dust shield
Non-reusable parts
Power steering oil
Special toolLock nut
Specified torque

Power Steering System-Power Steering Gear4-77Replacement1. Drain the power steering system fluid
2. Loosen the high pressure pipes.
Loosen the high pressure pipes with special tool
3. Loosen the low pressure pipes
Loosen the low pressure pipes with special tool
4. Separate the tie rod from the steering knuckle
(1) Remove the cotter pin, loosen the groove type lock nut
(2) Separate the tie rod ball stud joint from the steering knuckle
taper hole5. Loosen the thread screw of the high and low pressure pipe on the steering gear assembly
6. Remove the boot and press plate
7. Disconnect the power steering gear assembly from the steering column
Remove the steering gear pinion shaft spline lock bolt on the universal joint yoke
8. Remove power steering gear assembly
Remove 2 steering gear assembly set bolts. Remove the power steering gear assembly
9. Installation is in the reverse order of the removal
Notice:
(1) Insert the steering gear pinion shaft spline into the spline hole of the universal joint yoke, make sure that
the positions of the notch of the steering gear pinion shaft and the lock bolt of the universal joint yoke are
correct
(2) Secure the power steering gear with 2 bolts, torque: 125~152N.m
(3) Tighten the steering gear pinion shaft spline lock bolt on the universal joint yoke, torque: 22~34N.m
(4) Install the boot and press plate
(5) Install the threaded connector of the power steering high and low pressure pipe to the power steering gear,
torque: 25~32N.m

Power Steering System
-Power Steering Gear4-78 (6) Connect the tie rod ball stud pin with the steering knuckle, make sure that the mating surface of the tie rod
ball stud pin and the steering knuckle is clean, tighten the slot nut, torque: 27~39N.m. Install the cotter pin,
make sure of the correct installation
(7) Add appropriate amount of specified power steering fluid, bleed the power steering system
(8) Check the power steering pipeline system for leakage
(9) Check the front wheel alignment and front wheel left and right limit turn angle, adjust the toe in if
necessary and tighten the tie rod lock nut
(10) Check the position of the steering wheel. It is required that the steering wheel spokes are basically
symmetrical when the vehicle is driven straight ahead, reassemble the steering wheel if necessary

Adjustment1. Check and adjust the height of brake pedal.
(1) Check the height of brake pedal.
Height from the floor: 124.3-134.3mm
(2) Adjust the height of brake pedal.
a. Remove the cover of the console.
b. Remove the coupler from the brake light switch.
c. Loosen the lock nut of the brake light switch, and remove
the brake light switch.
d.Loosen the lock nub of the U-connector.
e.Turn the pedal push bar to adjust the height of brake
pedal.
f. Tighten the lock nub of the push bar.
Torque: 26N.m
g. Install the brake light switch.
h. Insert the connector of the brake light switch.
i. Push the brake pedal (5-15ram), and turn the brake light
switch till it goes out. Lock the nut in this position.
j. After installation, step down the brake pedal (5-15mm),
and check the brake light is bright.
2. Check the pedal free stroke.
(1) Shut down the motor, and step on the brake pedal repeatedly
till the booster is not vacuum.
(2) Step down the pedal till resistance appears, and measure the
distance as shown in the figure.
Pedal free travel: 1-6mm
If the clearance does not meet the requirement, check the
clearance of the brake light switch. If the clearance is correct,
make diagnosis on the braking system.
Clearance: 0.5-2.4mm
3. Check the pedal reserved distance.
Loosen the parking brake extension rod.
When the motor is running, step down the pedal, and measure the
pedal reserved distance as shown in the figure.
When stepping on the pedal 490N, the reserved distance from the
asphalt floor is larger than 55mm
If the distance doesn't meet the requirement, make diagnosis on
the braking system.Brake System -Brake Pedal4-83Braking lamp switch
Push parBraking pedel
heightFree travel for
braking pedalReverse of braking
pedal

1
2
3Brake System -Brake Pedal4-84Removal After the installation, check and adjust the height, free stroke and reserved distance of the brake pedal.
1. Remove the combination instrument component (see figure 1).
2. Unfix the brake master cylinder push bar U-connector.
Remove the clip and pin, and unfix the master cylinder handspike from the brake pedal.
3. Remove the brake pedal bracket.
(1) Remove the bolt from the brake pedal bracket (see figure 1).
(2) Unfix the brake light coupler.
(3) Remove the four nuts and brake pedal bracket (see figure 2).
4. Remove the brake pedal sub-assembly.
(1) Remove the bolt and nut from the brake pedal bracket.
(2) Remove the brake pedal and the two bushings.
5. Remove the brake light switch component.
(1) Loosen the lock nut of the brake light switch.
(2) Remove the brake light switch from the brake pedal bracket.
6. Remove the brake pedal pad.
Remove the brake pedal pad from the brake pedal.
7. Install the brake pedal pad.
Install the brake pedal pad on the brake pedal.
8. Install the brake light switch component.
Install the brake light switch on the brake pedal bracket.
9. Install the brake pedal.
(1) Apply lithium soap-base glycol lube on the end surface and side surface of the two new bushings.
(2) Install the brake pedal and the two bushings on the brake pedal bracket with bolts and nuts.
Torque: 37N.m
10. Install the brake pedal bracket.
(1) Install the brake pedal bracket with four nuts.
Torque: 25N.m
(2) Connect the connector of the brake light switch.
(3) Install the bolt on the brake pedal bracket (see figure 3).
Torque: 20N.m
11. Connect and install the brake cylinder push bar U-connector.
(1) Apply the lithium soap-base glycol lube on the handspike pin.
(2) Connect the master cylinder handspike with pins and clips.
12. Install the combination instrument components.
13. Check and adjust the brake pedal height.
14. Check the brake pedal's free travel.
15. Check the brake pedal's reserved distance.

Component ViewBrake System -Brake Master Cylinder Assembly4-86With ABS:
Cover
Brake fluid reservoir
Strainer
Automatic Transmission
O-ring
Retaining ring
Pin
Straight pinPiston guide
block
Cup
Washer
#1 piston & Spring
#2 piston
Spring Hole connectorHole
connector
Master cylinder
Without ABS
Cover
Strainer
PinManual Transmission
O-ring
Retaining ring
Hole connector
Piston guide block
Cup
#1 piston & Spring
#2 piston & Spring
Washer
Piston limit bolt Master cylinder Hole connectorSpecified torque
Non-reusable parts
Lithium soap base glycol lube

Repair1. Discharge the brake fluid.
Note: Never spray the brake fluid on the paint surface, otherwise
wash it immediately.
2. Remove the brake master cylinder.
(1) Pull out the connector of the level alarm light switch.
(2) Slide the clip, and pull out #1 clutch storage tank pipe (manual
transaxle).
(3) Remove the two brake pipes from the brake master cylinder
with special tool.(with ABS)
(4) Remove the three brake pipes from the brake master cylinder
accessory with special tool. (without ABS)
(5) Remove the two lock nuts, and pull out the brake master
pump.
3. Remove the storage tank.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the pin from the brake master cylinder body with
punch and hammer.
(3) Pull out the Brake fluid reservoir.
(4) Remove the cover and strainer from the storage tank.
(5) Remove the storage tank and the two hole connectors.
4. Remove the brake master cylinder.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the O-ring.
(3) Push the piston with hand, and remove the snap ring with
snap ring pliers.Brake System -Brake Master Cylinder Assembly4-87With ABS:
Without ABS