engine INFINITI QX56 2007 Factory User Guide

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-27
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P Operation Procedure
1. Touch “DATA MONITOR” on "SELECT DIAG MODE" screen.
2. Touch “ECU INPUT SIGNALS”, “MAIN SIGNALS“, or “SELEC-
TION FROM MENU” on "SELECT MONITOR ITEM" screen.
Monitored Item
×: Applicable
BCIA0031E
WDIA0084E
Monitored Item [unit] MAIN SIGNALSECU IN-
PUT SIG-
NALSSELECTION
FROM MENUDescription
VHCL SPEED SE
[km/h] or [mph]×××Indicates vehicle speed calculated from
wheel speed sensor signal.
SET VHCL SPD
[km/h] or [mph]××Indicates set vehicle speed stored in ICC
unit.
THRTL OPENING
[%]×××Indicates throttle angle calculated from sig-
nal voltage of throttle position sensor.
ENGINE RPM
[rpm]××Indicates engine speed read by ICC unit via
CAN communication (ECM transmits engine
speed via CAN communication).
DISTANCE ADJ
[SHOR/MID/LONG]×××Indicates set distance stored in ICC unit.
WIPER SW
[OFF/LOW/HIGH]××Indicates wiper [OFF/LOW/HIGH] status.
MAIN SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
SET/COAST SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
CANCEL SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
RESUME/ACC SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
control switch signal.
CRUISE OPE
[ON/OFF]××Indicates whether vehicle speed is being
controlled or not (ON means “controlling”).
BRAKE SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
ICC brake switch signal.

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-29
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
1. Touch “ACTIVE TEST” on "SELECT DIAG MODE" screen.
2. Touch any of “ICC BUZZER 1”, “METER LAMP”, “STOP LAMP”
and “BOOSTER SOL/V 3” on "SELECT TEST ITEM" screen.
3. Touch “START”.
4. Active test screen will be shown.
ICC BUZZER 1
• Touch “ON” and “OFF” to check that ICC warning chime operates
as in the following chart.
METER LAMP
• Start engine.
• Touch “ON” and “OFF” to check that ICC system displays operate as required.
• The following ICC lamps will illuminate at the same time, CRUISE
(orange), CRUISE (green), SET and ICC digital display.
STOP LAMP
BCIA0031E
SKIA6195E
ICC BUZZER 1 ON OFF
Buzzer sound Beep Not activated
SKIA1228E
METER LAMP ON OFF
All ICC system displays Full illumination OFF
SKIA1231E

ACS-30
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
• Touch “ON” and “OFF” to check that the stop lamps operate as in
the following chart.
BOOSTER SOL/V 3
• Touch any of “MODE 1”, “MODE 2”, “MODE 3” to check that follow-
ing operation condition is caused by operating monitor and brake
pedal.
• “START” is displayed 10 seconds after operation start. (Active test
is completed.)
Self-Diagnostic FunctionINFOID:0000000003533793
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9 .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may be malfunctioning and should
be replaced. Refer to ACS-55
.
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. Refer to ACS-34, "
Diagnostic Trouble Code (DTC) Chart", perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULTS”, and “ERASE” on CONSULT-II.
CAUTION:
DTC of an existing malfunction will not erase. If the memory does not erase, GO TO step 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
STOP LAMP ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E
SKIA1233E
PKIA0363J

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-31
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9.
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and wait 5 seconds. Press ACCEL/RES
switch 5 times, and then press COAST/SET switch 5 times all
within 5 seconds to start self-diagnosis.
CAUTION:
• Do not start the engine.
• Do not press the ICC ON/OFF switch ON.
• When operation above is not completed within the 5 to 10 sec-
ond window, DTC will not be displayed.
• If self-diagnosis mode cannot be started after several
attempts, the ICC unit may be malfunctioning and should be
replaced. Refer to "SELF-DIAGNOSIS BY ICC SYSTEM DIS-
PLAY WILL NOT RUN".
5. When self-diagnosis mode is started, DTCs are shown on set vehicle speed indicator.
CAUTION:
• DTC will disappear after 5 minutes.
• When multiple malfunctions are detected, a maximum of 3 code numbers can be stored; the lat-
est malfunction will be displayed first.
6. Check ACS-34, "
Diagnostic Trouble Code (DTC) Chart" , and repair or replace if necessary.
7. After repair, erase DTC stored in the ICC unit. Refer to "Self-Diagnostic Erasing Method".
8. DTC 55 will be shown.
9. Turn ignition switch OFF to exit the diagnosis.
10. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
Self-Diagnostic Erasing Method
1. Stop the vehicle and turn the ignition switch OFF.
2. Turn ignition switch ON and start self-diagnosis.
3. During self-diagnosis mode, press CANCEL switch 5 times, and DISTANCE switch 5 times within a 10
second time period.
CAUTION:
• Switch inputs must be received within a 10 second time period.
• When operation is not completed within 10 seconds start again from step 1.
4. DTC 55 will be shown.
CAUTION:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
WKIA1921E
WKIA1922E

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-53
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
• Perform ICC system running test. Refer to ACS-9, "ICC System Running Test" . Then perform
self-diagnosis of ICC system again.
Symptom 8 the System Does Not Detect the Vehicle Ahead at AllINFOID:0000000003533822
1.VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check combination meter. Refer to DI-15, "
How to Proceed with Trouble Diagnosis".
2. VISUAL CHECK
• Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Perform ICC system running
test. Refer to ACS-9, "
ICC System Running Test".
NG >> GO TO 3.
3.VISUAL CHECK
• Check ICC sensor body window for cracks and scratches.
OK or NG
OK >> GO TO 4.
NG >> • Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-55, "
ICC Sen-
sor".
• Perform ICC system running test. Refer to ACS-9, "
ICC System Running Test". Then perform
self-diagnosis of ICC system again.
4.ADJUST ICC SENSOR
• After performing laser beam aiming adjustment, perform ICC system running test. Refer to ACS-9, "
ICC Sys-
tem Running Test". Check that preceding vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >> • Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-55, "
ICC Sen-
sor".
• Perform ICC system running test. Refer to ACS-9, "
ICC System Running Test". Then perform
self-diagnosis of ICC system again.

AT-1
TRANSMISSION/TRANSAXLE
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
N
O
P
CONTENTS
AUTOMATIC TRANSMISSION
SERVICE INFORMATION ............................6
INDEX FOR DTC .................................................6
Alphabetical Index .....................................................6
DTC No. Index ..........................................................6
PRECAUTIONS ...................................................8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................
8
Precaution for On Board Diagnosis (OBD) System
of A/T and Engine .....................................................
8
Precaution .................................................................8
Service Notice or Precaution .....................................9
PREPARATION ..................................................11
Special Service Tool ...............................................11
Commercial Service Tool ........................................12
A/T FLUID ...........................................................13
Changing Automatic Transmission Fluid (ATF) ......13
Checking Automatic Transmission Fluid (ATF) .......13
A/T Fluid Cooler Cleaning .......................................15
A/T CONTROL SYSTEM ....................................19
Cross-Sectional View (2WD models) ......................19
Cross-Sectional View (4WD models) ......................20
Shift Mechanism ......................................................20
TCM Function ..........................................................31
CAN Communication ...............................................32
Input/Output Signal of TCM .....................................33
Line Pressure Control .............................................33
Shift Control ............................................................35
Lock-up Control .......................................................36
Engine Brake Control ..............................................37
Control Valve ...........................................................37
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......39
Introduction .............................................................39
OBD-II Function for A/T System ..............................39
One or Two Trip Detection Logic of OBD-II ............39
OBD-II Diagnostic Trouble Code (DTC) ..................39
Malfunction Indicator Lamp (MIL) ............................41
TROUBLE DIAGNOSIS ....................................43
DTC Inspection Priority Chart ..................................43
Fail-Safe ..................................................................43
How To Perform Trouble Diagnosis for Quick and
Accurate Repair .......................................................
44
A/T Electrical Parts Location ...................................50
Circuit Diagram ........................................................51
Inspections Before Trouble Diagnosis .....................51
Check Before Engine Is Started ..............................55
Check at Idle ............................................................55
Cruise Test - Part 1 .................................................56
Cruise Test - Part 2 .................................................58
Cruise Test - Part 3 .................................................59
Vehicle Speed When Shifting Gears .......................59
Vehicle Speed When Performing and Releasing
Complete Lock-up ...................................................
60
Vehicle Speed When Performing and Releasing
Slip Lock-up .............................................................
60
Symptom Chart ........................................................60
TCM Input/Output Signal Reference Value .............82
CONSULT-II Function (A/T) ....................................83
DTC U1000 CAN COMMUNICATION LINE .....91
Description ...............................................................91
On Board Diagnosis Logic .......................................91
Possible Cause ........................................................91
DTC Confirmation Procedure ..................................91
Wiring Diagram - AT - CAN .....................................92
Diagnosis Procedure ...............................................93
DTC P0615 START SIGNAL CIRCUIT .............94
Description ...............................................................94
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................
94
On Board Diagnosis Logic .......................................94
Possible Cause ........................................................94
DTC Confirmation Procedure ..................................94
Wiring Diagram - AT - STSIG ..................................95
Diagnosis Procedure ...............................................95

AT-2
DTC P0700 TCM ................................................98
Description ..............................................................98
On Board Diagnosis Logic ......................................98
Possible Cause .......................................................98
DTC Confirmation Procedure .................................98
Diagnosis Procedure ..............................................98
DTC P0705 PARK/NEUTRAL POSITION
SWITCH .............................................................
99
Description ..............................................................99
CONSULT-II Reference Value in Data Monitor
Mode .......................................................................
99
On Board Diagnosis Logic ......................................99
Possible Cause .......................................................99
DTC Confirmation Procedure .................................99
Wiring Diagram - AT - PNP/SW .............................100
Diagnosis Procedure .............................................100
DTC P0717 TURBINE REVOLUTION SEN-
SOR ..................................................................
103
Description .............................................................103
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
103
On Board Diagnosis Logic .....................................103
Possible Cause ......................................................103
DTC Confirmation Procedure ................................103
Diagnosis Procedure .............................................103
DTC P0720 VEHICLE SPEED SENSOR A/T
(REVOLUTION SENSOR) ...............................
105
Description .............................................................105
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
105
On Board Diagnosis Logic .....................................105
Possible Cause ......................................................105
DTC Confirmation Procedure ................................105
Wiring Diagram - AT - VSSA/T ..............................106
Diagnosis Procedure .............................................107
DTC P0725 ENGINE SPEED SIGNAL ............109
Description .............................................................109
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
109
On Board Diagnosis Logic .....................................109
Possible Cause ......................................................109
DTC Confirmation Procedure ................................109
Diagnosis Procedure .............................................109
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE ..........................................
111
Description .............................................................111
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
111
On Board Diagnosis Logic .....................................111
Possible Cause ......................................................111
DTC Confirmation Procedure ................................111
Diagnosis Procedure .............................................111
DTC P0744 A/T TCC S/V FUNCTION (LOCK-
UP) ...................................................................
113
Description ............................................................113
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
113
On Board Diagnosis Logic ....................................113
Possible Cause .....................................................113
DTC Confirmation Procedure ................................113
Diagnosis Procedure .............................................114
DTC P0745 LINE PRESSURE SOLENOID
VALVE ..............................................................
115
Description ............................................................115
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
115
On Board Diagnosis Logic ....................................115
Possible Cause .....................................................115
DTC Confirmation Procedure ................................115
Diagnosis Procedure .............................................115
DTC P1705 THROTTLE POSITION SENSOR ..117
Description ............................................................117
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
117
On Board Diagnosis Logic ....................................117
Possible Cause .....................................................117
DTC Confirmation Procedure ................................117
Diagnosis Procedure .............................................117
DTC P1710 A/T FLUID TEMPERATURE SEN-
SOR CIRCUIT ...................................................
119
Description ............................................................119
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
119
On Board Diagnosis Logic ....................................119
Possible Cause .....................................................119
DTC Confirmation Procedure ................................119
Wiring Diagram - AT - FTS ...................................120
Diagnosis Procedure .............................................120
Component Inspection ..........................................122
DTC P1721 VEHICLE SPEED SENSOR MTR ..124
Description ............................................................124
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ................................124
Diagnosis Procedure .............................................124
DTC P1730 A/T INTERLOCK ...........................126
Description ............................................................126
On Board Diagnosis Logic ....................................126
Possible Cause .....................................................126
DTC Confirmation Procedure ................................126
Judgement of A/T Interlock ...................................126
Diagnosis Procedure .............................................127
DTC P1731 A/T 1ST ENGINE BRAKING ........128
Description ............................................................128
CONSULT-II Reference Value in Data Monitor
Mode .....................................................................
128

AT-4
DTC Confirmation Procedure ................................152
Diagnosis Procedure .............................................152
DTC P1845 ATF PRESSURE SWITCH 5 ........154
Description .............................................................154
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
154
On Board Diagnosis Logic .....................................154
Possible Cause ......................................................154
DTC Confirmation Procedure ................................154
Diagnosis Procedure .............................................154
DTC P1846 ATF PRESSURE SWITCH 6 ........156
Description .............................................................156
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
156
On Board Diagnosis Logic .....................................156
Possible Cause ......................................................156
DTC Confirmation Procedure ................................156
Diagnosis Procedure .............................................156
MAIN POWER SUPPLY AND GROUND CIR-
CUIT .................................................................
158
Wiring Diagram - AT - MAIN ..................................158
Diagnosis Procedure .............................................159
CLOSED THROTTLE POSITION AND WIDE
OPEN THROTTLE POSITION CIRCUIT .........
161
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
161
Diagnosis Procedure .............................................161
BRAKE SIGNAL CIRCUIT ..............................162
CONSULT-II Reference Value in Data Monitor
Mode ......................................................................
162
Diagnosis Procedure .............................................162
TOW MODE SWITCH ......................................163
Description .............................................................163
Wiring Diagram - AT - TMSW ................................163
Diagnosis Procedure .............................................164
TROUBLE DIAGNOSIS FOR SYMPTOMS .....165
Wiring Diagram - AT - NONDTC ............................165
A/T Check Indicator Lamp Does Not Come On .....167
Engine Cannot Be Started in "P" or "N" Position ...168
In "P" Position, Vehicle Moves When Pushed .......168
In "N" Position, Vehicle Moves ..............................169
Large Shock ("N" to "D" Position) ..........................170
Vehicle Does Not Creep Backward in "R" Position ..172
Vehicle Does Not Creep Forward in "D" Position ..175
Vehicle Cannot Be Started from D1 .......................177
A/T Does Not Shift: D1→ D2 ..................................179
A/T Does Not Shift: D2→ D3 ..................................181
A/T Does Not Shift: D3→ D4 ..................................183
A/T Does Not Shift: D4→ D5 ..................................185
A/T Does Not Perform Lock-up .............................187
A/T Does Not Hold Lock-up Condition ...................189
Lock-up Is Not Released .......................................190
Engine Speed Does Not Return to Idle .................191
A/T Does Not Shift: 5th gear → 4th gear ..............192
A/T Does Not Shift: 4th gear → 3rd gear ..............194
A/T Does Not Shift: 3rd gear → 2nd gear .............196
A/T Does Not Shift: 2nd gear → 1st gear .............197
Vehicle Does Not Decelerate By Engine Brake ....199
A/T SHIFT LOCK SYSTEM ..............................202
Description ............................................................202
Shift Lock System Electrical Parts Location ..........202
Wiring Diagram - AT - SHIFT ................................203
Shift Lock Control Unit Reference Value ..............204
Component Inspection ..........................................204
SHIFT CONTROL SYSTEM .............................207
Control Device Removal and Installation ..............207
Adjustment of A/T Position ....................................208
Checking of A/T Position .......................................208
ON-VEHICLE SERVICE ...................................209
Oil Pan ..................................................................209
Control Valve with TCM and A/T Fluid Tempera-
ture Sensor 2 ........................................................
210
Rear Oil Seal .........................................................219
AIR BREATHER HOSE ....................................221
Removal and Installation .......................................221
TRANSMISSION ASSEMBLY ..........................223
Removal and Installation (2WD) ...........................223
Removal and Installation (4WD) ...........................225
OVERHAUL ......................................................228
Component ...........................................................228
Oil Channel ...........................................................235
Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................
237
DISASSEMBLY ................................................240
Disassembly ..........................................................240
REPAIR FOR COMPONENT PARTS ..............258
Oil Pump ...............................................................258
Front Sun Gear, 3rd One-Way Clutch ...................260
Front Carrier, Input Clutch, Rear Internal Gear .....262
Mid Sun Gear, Rear Sun Gear, High and Low Re-
verse Clutch Hub ..................................................
267
High and Low Reverse Clutch ..............................272
Direct Clutch .........................................................274
ASSEMBLY ......................................................277
Assembly (1) .........................................................277
Adjustment ............................................................290
Assembly (2) .........................................................292
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
298
General Specification ............................................298
Vehicle Speed When Shifting Gears .....................298
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................
299
Stall Speed ............................................................299

AT-6
< SERVICE INFORMATION >
INDEX FOR DTC
SERVICE INFORMATION
INDEX FOR DTC
Alphabetical IndexINFOID:0000000003532216
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 1
.
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.
DTC No. IndexINFOID:0000000003532217
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 1
.
Items
(CONSULT- II screen terms) DTC
Reference page OBD- II Except OBD- II
CONSULT- II GST (*1) CONSULT- II only “A/T”
A/T 1ST E/BRAKING — P1731AT- 1 2 8
ATF PRES SW 1/CIRC — P1841AT- 1 5 0
ATF PRES SW 3/CIRC — P1843AT- 1 5 2
ATF PRES SW 5/CIRC — P1845AT- 1 5 4
ATF PRES SW 6/CIRC — P1846AT- 1 5 6
A/T INTERLOCK P1730 P1730AT- 1 2 6
A/T TCC S/V FNCTN P0744 P0744 AT- 11 3
ATF TEMP SEN/CIRC P0710 P1710AT- 11 9
CAN COMM CIRCUIT U1000 U1000AT- 9 1
D/C SOLENOID/CIRC P1762 P1762AT- 1 3 8
D/C SOLENOID FNCTN P1764 (*2) P1764 AT- 1 4 0
ENGINE SPEED SIG — P0725AT- 1 0 9
FR/B SOLENOID/CIRC P1757 P1757AT- 1 3 4
FR/B SOLENOID FNCT P1759 P1759 AT- 1 3 6
HLR/C SOL/CIRC P1767 P1767AT- 1 4 2
HLR/C SOL FNCTN P1769 (*2) P1769 AT- 1 4 4
I/C SOLENOID/CIRC P1752 P1752AT- 1 3 0
I/C SOLENOID FNCTN P1754 (*2) P1754 AT- 1 3 2
L/PRESS SOL/CIRC P0745 P0745AT- 11 5
LC/B SOLENOID/CIRC P1772 P1772AT- 1 4 6
LC/B SOLENOID FNCT P1774 P1774 AT- 1 4 8
PNP SW/CIRC P0705 P0705AT- 9 9
STARTER RELAY/CIRC — P0615AT- 9 4
TCC SOLENOID/CIRC P0740 P0740AT- 111
TCM P0700 P0700AT- 9 8
TP SEN/CIRC A/T — P1705AT- 11 7
TURBINE REV S/CIRC P0717 P0717AT- 1 0 3
VEH SPD SE/CIR·MTR — P1721AT- 1 2 4
VEH SPD SEN/CIR AT P0720 P0720AT- 1 0 5

INDEX FOR DTC
AT-7
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT- II screen terms)Reference page OBD- II Except OBD- II
CONSULT- II
GST (*1)C O N S U LT- I I
only “A/T”
— P0615 STARTER RELAY/CIRCAT- 9 4
P0700 P0700 TCMAT- 9 8
P0705 P0705 PNP SW/CIRCAT- 9 9
P0710 P1710 ATF TEMP SEN/CIRCAT- 11 9
P0717 P0717 TURBINE REV S/CIRCAT- 1 0 3
P0720 P0720 VEH SPD SEN/CIR ATAT- 1 0 5
— P0725 ENGINE SPEED SIGAT- 1 0 9
P0740 P0740 TCC SOLENOID/CIRCAT- 111
P0744 P0744 A/T TCC S/V FNCTNAT- 11 3
P0745 P0745 L/PRESS SOL/CIRCAT- 11 5
— P1705 TP SEN/CIRC A/TAT- 11 7
— P1721 VEH SPD SE/CIR·MTRAT- 1 2 4
P1730 P1730 A/T INTERLOCKAT- 1 2 6
— P1731 A/T 1ST E/BRAKINGAT- 1 2 8
P1752 P1752 I/C SOLENOID/CIRCAT- 1 3 0
P1754 (*2) P1754 I/C SOLENOID FNCTNAT- 1 3 2
P1757 P1757 FR/B SOLENOID/CIRCAT- 1 3 4
P1759 (*2) P1759 FR/B SOLENOID FNCTAT- 1 3 6
P1762 P1762 D/C SOLENOID/CIRCAT- 1 3 8
P1764 (*2) P1764 D/C SOLENOID FNCTNAT- 1 4 0
P1767 P1767 HLR/C SOL/CIRCAT- 1 4 2
P1769 P1769 HLR/C SOL FNCTNAT- 1 4 4
P1772 P1772 LC/B SOLENOID/CIRCAT- 1 4 6
P1774 P1774 LC/B SOLENOID FNCTAT- 1 4 8
— P1841 ATF PRES SW 1/CIRCAT- 1 5 0
— P1843 ATF PRES SW 3/CIRCAT- 1 5 2
— P1845 ATF PRES SW 5/CIRCAT- 1 5 4
— P1846 ATF PRES SW 6/CIRCAT- 1 5 6
U1000 U1000 CAN COMM CIRCUITAT- 9 1