INFINITI QX56 2007 Factory Workshop Manual

ACS-28
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACTIVE TEST
CAUTION:
Do not perform the active test while driving. Active test cannot be started while ICC system warning
indicator is illuminated.
Active Test
STOP LAMP SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from
stop lamp switch signal.
RELEASE SW NO
[ON/OFF]
××Indicates [ON/OFF] status as judged from
release switch signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[ON/OFF]
××Indicates [ON/OFF] status as judged from
release switch signal.
OFF when brake is depressed.
ON when brake is not depressed.
IDLE SW
[ON/OFF]
××Indicates [ON/OFF] status of idle switch
read by ICC unit via CAN communication
(ECM transmits ON/OFF status via CAN
communication).
GEAR
[1, 2, 3, 4, 5]××Indicates A/T gear position read by ICC unit
via CAN communication (TCM transmits
gear position via CAN communication).
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC warning
output.
ICC WARNING×NOTE:
This item is displayed but cannot be moni-
tored.
VHCL SPD AT
[km/h] or [mph]
×Indicates vehicle speed calculated from A/T
vehicle speed sensor by ICC unit via CAN
communication (TCM transmits A/T vehicle
speed sensor signal via CAN communica-
tion).
PRESS SENS
[bar]×××Indicates brake fluid pressure value calculat-
ed from signal voltage of pressure sensor.
PRESS SENS 2
[bar]××NOTE:
This item is displayed but cannot be moni-
tored.
D RANGE SW
[ON/OFF]
××Indicates [ON/OFF] status of “D” position
read by ICC unit via CAN communication
(TCM transmits ON/OFF condition of “D” po-
sition via CAN communication).
A/T OD OFF
[ON/OFF]×Indicates [ON/OFF] status of OD cancel out-
put under control.
NP RANGE SW
[ON/OFF]××Indicates PNP switch signal read by ICC unit
via CAN communication. (TCM transmits
PNP switch signal via CAN communication)
DISTANCE×NOTE:
This item is displayed but cannot be moni-
tored.
RELATIVE SPD×NOTE:
This item is displayed but cannot be moni-
tored.
STP LMP DRIVE
[ON/OFF]××Indicates [ON/OFF] status of brake hold re-
lay drive output. Monitored Item [unit] MAIN SIGNALSECU IN-
PUT SIG-
NALSSELECTION
FROM MENUDescription

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-29
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
1. Touch “ACTIVE TEST” on "SELECT DIAG MODE" screen.
2. Touch any of “ICC BUZZER 1”, “METER LAMP”, “STOP LAMP”
and “BOOSTER SOL/V 3” on "SELECT TEST ITEM" screen.
3. Touch “START”.
4. Active test screen will be shown.
ICC BUZZER 1
• Touch “ON” and “OFF” to check that ICC warning chime operates
as in the following chart.
METER LAMP
• Start engine.
• Touch “ON” and “OFF” to check that ICC system displays operate as required.
• The following ICC lamps will illuminate at the same time, CRUISE
(orange), CRUISE (green), SET and ICC digital display.
STOP LAMP
BCIA0031E
SKIA6195E
ICC BUZZER 1 ON OFF
Buzzer sound Beep Not activated
SKIA1228E
METER LAMP ON OFF
All ICC system displays Full illumination OFF
SKIA1231E

ACS-30
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
• Touch “ON” and “OFF” to check that the stop lamps operate as in
the following chart.
BOOSTER SOL/V 3
• Touch any of “MODE 1”, “MODE 2”, “MODE 3” to check that follow-
ing operation condition is caused by operating monitor and brake
pedal.
• “START” is displayed 10 seconds after operation start. (Active test
is completed.)
Self-Diagnostic FunctionINFOID:0000000003533793
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9 .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may be malfunctioning and should
be replaced. Refer to ACS-55
.
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. Refer to ACS-34, "
Diagnostic Trouble Code (DTC) Chart", perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULTS”, and “ERASE” on CONSULT-II.
CAUTION:
DTC of an existing malfunction will not erase. If the memory does not erase, GO TO step 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
STOP LAMP ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E
SKIA1233E
PKIA0363J

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-31
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9.
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and wait 5 seconds. Press ACCEL/RES
switch 5 times, and then press COAST/SET switch 5 times all
within 5 seconds to start self-diagnosis.
CAUTION:
• Do not start the engine.
• Do not press the ICC ON/OFF switch ON.
• When operation above is not completed within the 5 to 10 sec-
ond window, DTC will not be displayed.
• If self-diagnosis mode cannot be started after several
attempts, the ICC unit may be malfunctioning and should be
replaced. Refer to "SELF-DIAGNOSIS BY ICC SYSTEM DIS-
PLAY WILL NOT RUN".
5. When self-diagnosis mode is started, DTCs are shown on set vehicle speed indicator.
CAUTION:
• DTC will disappear after 5 minutes.
• When multiple malfunctions are detected, a maximum of 3 code numbers can be stored; the lat-
est malfunction will be displayed first.
6. Check ACS-34, "
Diagnostic Trouble Code (DTC) Chart" , and repair or replace if necessary.
7. After repair, erase DTC stored in the ICC unit. Refer to "Self-Diagnostic Erasing Method".
8. DTC 55 will be shown.
9. Turn ignition switch OFF to exit the diagnosis.
10. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
Self-Diagnostic Erasing Method
1. Stop the vehicle and turn the ignition switch OFF.
2. Turn ignition switch ON and start self-diagnosis.
3. During self-diagnosis mode, press CANCEL switch 5 times, and DISTANCE switch 5 times within a 10
second time period.
CAUTION:
• Switch inputs must be received within a 10 second time period.
• When operation is not completed within 10 seconds start again from step 1.
4. DTC 55 will be shown.
CAUTION:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
WKIA1921E
WKIA1922E

ACS-32
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
6. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC system
warning lamp (orange) does not illuminate.
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY WILL NOT RUN
Self Diagnosis Will Not Run
1.CHECK ICC SYSTEM DISPLAY
When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> GO TO 2.
NO >> GO TO 5.
2.CHECK SELF-DIAGNOSIS
• Disconnect ECM connectors, and check for damaged, bent or loose terminals. Securely connect them
again.
• Can self-diagnosis for ICC system be performed?
YES or NO
YES >> Inspection End.
NO >> GO TO 3.
3.CHECK ICC STEERING SWITCH
Check ICC steering switch. Refer to ACS-54, "
ICC Steering Switch" .
OK or NG
OK >> GO TO 4.
WKIA1985E
Component Possible Cause Specific causes
ICC unit power supply malfunctionNo voltage supply from ignition switchFuse blown
Harness open
Harness shorted
Ground cable not connectedHarness open
Harness shorted
ICC steering switch malfunction No signal transmittedHarness open
Harness shorted
Spiral cable open
Spiral cable shorted
Switch or ECM malfunction
CAN communication system malfunction Signal not transmittedHarness open
Harness shorted
CAN communication outside the standard
Combination meter system malfunction Indication not possibleIndicator malfunction
Indicator segments disappear
ICC unit malfunction Internal malfunction ICC unit

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-33
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
NG >> Replace ICC steering switch. Refer to ACS-54, "ICC Steering Switch" .
4.CHECK HARNESS BETWEEN ECM AND ICC STEERING SWITCH
Check harness and spiral cable between ECM and ICC steering switch for open or short circuit.
OK or NG
OK >> GO TO 6
NG >> Repair or replace harness or spiral cable between ECM and ICC steering switch.
5.CHECK POWER SUPPLY FOR ICC UNIT
• Check ICC unit power supply, and repair if necessary.
• When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 6.
6.CHECK CONNECTOR FOR ICC UNIT
• Disconnect connectors ICC unit, and check terminals for bends and looseness. Securely connect them
again.
• When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 7.
7.CHECK CAN COMMUNICATION
Perform self-diagnosis with CONSULT-II, and check CAN communication system for malfunction.
OK or NG
OK >> Replace combination meter. Refer to DI-21, "Removal and Installation of Combination Meter" .
NG >> CAN communication inspection. Refer to ACS-37, "
DTC 20 CAN COMM CIRCUIT".

ACS-34
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Diagnostic Trouble Code (DTC) ChartINFOID:0000000003533794
×:Applicable
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake as-
sist (with
preview
function)
11 CONTROL UNIT×××ו ICC unit internal malfunctionACS-36,
"DTC 11
CON-
TROL
UNIT"
12 VDC CONTROL UNIT×××ו VDC malfunction
• Brake booster signal harness is
open or shortedACS-36,
"DTC 12
VDC
CON-
TROL
UNIT"
20 CAN COMM CIRCUIT×××ו ICC unit detected CAN communi-
cation malfunctionACS-37,
"DTC 20
CAN
COMM
CIR-
CUIT"
31 POWER SUPPLY CIR1×××ו ICC unit power supply voltage is
excessively low (less than 8V)ACS-37,
"DTC 31
POWER
SUPPLY
CIR1,
DTC 34
POWER
SUPPLY
CIR2"
34 POWER SUPPLY CIR2×××ו ICC unit power supply voltage is
excessively high.ACS-37,
"DTC 31
POWER
SUPPLY
CIR1,
DTC 34
POWER
SUPPLY
CIR2"
41 VHCL SPEED SE CIRC×××ו Wheel sensor malfunction
• ABS actuator and electric unit
(control unit) malfunction
• A/T vehicle speed sensor mal-
function
•TCM malfunctionACS-38,
"DTC 41
VHCL
SPEED
SE CIRC"
43 VDC/TCS/ABS CIRC×××ו VDC/TCS/ABS system malfunc-
tionACS-38,
"DTC 43
VDC/
TCS/ABS
CIRC"

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-35
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
45 BRAKE SW/ STOP L SW×××ו ICC brake switch or stop lamp
switch harness is open or shorted
• ICC brake switch or stop lamp
switch is stuck to OFF
• ICC brake switch or stop lamp
switch is stuck to ONACS-38,
"DTC 45
BRAKE
SW/
STOP L
SW"
46 OPERATION SW CIRC××ו ICC steering switch harness or
spiral cable is open or shorted
• ICC steering switch malfunctionACS-40,
"DTC 46
OPERA-
TION SW
CIRC"
74 LASER BEAM OFF CNTR×× ×• Laser beam of ICC sensor is off
the aiming pointACS-41,
"DTC 74
LASER
BEAM
OFF CN-
TR"
90 STOP LAMP RLY FIX×× ×• Normally open terminal of stop
lamp relay is stuckACS-41,
"DTC 90
STOP
LAMP
RLY FIX"
92 ECM CIRCUIT×××וECM malfunction
• Accelerator pedal position sensor
malfunction
• ICC unit malfunctionACS-45,
"DTC 92
ECM
CIR-
CUIT"
96 NP RANGE××ו Park/neutral position switch har-
ness is open or shorted
• Park/neutral position switch mal-
function
•TCM malfunctionACS-45, "DTC 96
NP
RANGE"
97 AT CIRCUIT××וTCM malfunctionACS-46, "DTC 97
AT CIR-
CUIT"
98 GEAR POSITION××וTCM malfunction
• A/T turbine revolution sensor mal-
function
• A/T vehicle speed sensor mal-
functionACS-46,
"DTC 98
GEAR
POSI-
TION"
102 LASER STAIN×× ×• ICC sensor body window has
contaminationACS-47, "DTC 102
LASER
STAIN"
103 LASER SENSOR FAIL×× ×• ICC sensor internal malfunctionACS-47,
"DTC 103
LASER
SEN-
SOR
FA I L"
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Veh ic le-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake as-
sist (with
preview
function)

ACS-36
< SERVICE INFORMATION >[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
NOTE: DTC 55 will display when no malfunction is detected.
DTC 11 CONTROL UNITINFOID:0000000003533795
1.DIAGNOSTIC CHECK
Are any items other than “DTC 11 CONTROL UNIT” indicated on self-diagnosis display?
YES or NO
YES >> Repair or replace as necessary. Erase DTC and perform ICC system running test. Refer to ACS-
9, "ICC System Running Test" . Then perform self-diagnosis of ICC system again.
NO >> Replace ICC unit. Refer to ACS-55
. Erase DTC and perform ICC system running test. Refer to
ACS-9, "
ICC System Running Test". Then perform self-diagnosis of ICC system again.
DTC 12 VDC CONTROL UNITINFOID:0000000003533796
1.DIAGNOSIS CHECK
With CONSULT-II
Perform self-diagnosis of ABS actuator and electric unit (control unit). Is malfunction indicated?
YES or NO
YES >> Repair or replace as necessary. Erase DTC and perform ICC system running test. Refer to ACS-
9, "ICC System Running Test". Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2.CHECK CONNECTOR ICC UNIT AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
1. Turn ignition switch OFF.
2. Disconnect ICC unit, and ABS actuator and electric unit (control unit) connectors, and connect them
securely again. Erase DTC, then perform self-diagnosis of ICC system again.
OK or NG
OK >> Poor connector connection. Check connector housing for disconnected, loose, bent and collapsed
terminals. If any malfunction is detected, repair as necessary. Erase DTC and perform ICC sys-
tem running test. Refer to ACS-9, "
ICC System Running Test". Then perform self-diagnosis of ICC
system again.
NG >> GO TO 3.
3.CHECK HARNESS BETWEEN ICC UNIT AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
104 LASER AIMING INCMP×× ×• Laser beam aiming of ICC sensor
is not adjustedACS-48,
"DTC 104
LASER
AIMING
INCMP"
107 LASER COMM FAIL×× ×• CAN data received by ICC sensor
is strange (from ICC unit, combi-
nation meter or ECM)ACS-48,
"DTC 107
LASER
COMM
FA IL"
109 LASER HIGH TEMP×× ×• Temperature around ICC sensor
is excessively highACS-48,
"DTC 109
LASER
HIGH
TEMP"
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake as-
sist (with
preview
function)

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-37
< SERVICE INFORMATION >[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
N
O
P
1. Turn ignition switch OFF.
2. Disconnect ICC unit and ABS actuator and electric unit (control
unit) connectors.
3. Check continuity between ICC unit harness connector B13 ter-
minal 10, and ABS actuator and electric unit (control unit) con-
nector E125 terminal 7.
OK or NG
OK >> Replace ICC unit. Refer to ACS-55. Erase DTC and per-
form ICC system running test. Refer to ACS-9, "
ICC
System Running Test". Then perform self-diagnosis of ICC system again.
NG >> • Repair harness between ICC unit, and ABS actuator and electric unit (control unit).
• Erase DTC and perform ICC system running test. Refer to ACS-9, "
ICC System Running Test".
Then perform self-diagnosis of ICC system again.
DTC 20 CAN COMM CIRCUITINFOID:0000000003533797
1.CHECK CAN COMMUNICATION
With CONSULT-II
1. Perform self-diagnosis.
2. Print self-diagnostic result.
>> After printing self-diagnostic result, GO TO “CAN system”. Refer to LAN-4, "
CAN Communication
System" .
DTC 31 POWER SUPPLY CIR1, DTC 34 POWER SUPPLY CIR2INFOID:0000000003533798
1.CHECK ICC UNIT CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect ICC unit connectors and connect them securely again. Erase DTC, then perform self-diagno-
sis of ICC system again.
OK or NG
OK >> GO TO 2.
NG >> • Poor connector connection.
• Check connector. Check connector housing for disconnected, loose, bent, and collapsed termi-
nals. If any malfunction is detected, repair as as necessary. Erase DTC and perform ICC system
running test. Refer to ACS-9, "
ICC System Running Test". Then perform self-diagnosis of ICC
system again.
2.CHECK POWER SUPPLY CIRCUIT FOR ICC UNIT
1. Turn ignition switch ON.
2. Check voltage between ICC unit harness connector B17 termi-
nal 33, 42 and ground.
OK or NG
OK >> GO TO 3.
NG >> • Repair ICC unit power supply harness.
• Erase DTC and perform ICC system running test.
Refer to ACS-9, "
ICC System Running Test". Then
perform self-diagnosis of ICC system again.
3.CHECK GROUND CIRCUIT FOR ICC UNITContinuity should exist.
WKIA3616E
Battery voltage should exist.
SKIA1173E