sensor INFINITI QX56 2011 Factory Service Manual

LAN
HOW TO USE THIS SECTIONLAN-23
< HOW TO USE THIS MANUAL > [CAN]
C
D
E
F
G H
I
J
K L
B A
O P
N
HOW TO USE THIS MANUAL
HOW TO USE THIS SECTION
CautionINFOID:0000000006220525
 This section describes information peculiar to a vehicle and inspection procedures.
 For trouble diagnosis procedure, refer to
LAN-18, "
Trouble Diagnosis Procedure".
Abbreviation ListINFOID:0000000006220526
Unit name abbreviations in CONSULT-III CAN diagnosis and in this section are as per the following list.
Abbreviation Unit name
4WD Transfer control unit
A-BAG Air bag diagnosis sensor unit ABS ABS actuator and electric unit (control unit)
ADP Driver seat control unit AFS AFS control unitAPA Accelerator pedal actuator AV AV control unit
BCM BCM
CGW CAN gateway DLC Data link connector
E-SUS Air levelizer control module ECM ECM
HVAC A/C auto amp. ICC ADAS control unit
IPDM-E IPDM E/R LANE Lane camera unit
LASER ICC sensor M&A Combination meter
PSB Pre-crash seat belt control unit (driver side)
PWBD Automatic back door control module
RDR-L Side radar LH
RDR-R Side radar RH STRG Steering angle sensor TCM TCM
TPMS Low tire pressure warning control unit
Revision: 2010 May2011 QX56

LAN-24
< PRECAUTION >[CAN]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint S
ystem (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006238426
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minu tes before performing any service.
Precautions for Trouble DiagnosisINFOID:0000000006220528
CAUTION:
 Never apply 7.0 V or more to the measurement terminal.
 Use a tester with open terminal voltage of 7.0 V or less.
 Turn the ignition switch OFF and disconnect th e battery cable from the negative terminal when
checking the harness.
Precautions for Harness RepairINFOID:0000000006220529
 Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
SKIB8766E
Revision: 2010 May2011 QX56

LAN-26
< SYSTEM DESCRIPTION >[CAN]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006220530
1. Air bag diagnosis sensor unit 2. Lane camera unit 3. A/T assembly
4. AFS control unit 5. Transfer control unit 6. Low tire pressure warning control
unit
7. IPDM E/R 8. CAN gateway 9. ECM
10. A/C auto amp. 11. ICC sensor 12. AV control unit
13. BCM 14. ABS actuator an d electric unit (con-
trol unit) 15. Combination meter
16. Data link connector 17. Steering angle sensor 18. Accelerator pedal actuator
19. Driver seat control un it 20. Pre-crash seat be lt control unit (driv-
er side) 21. Air levelizer control module
22. ADAS control unit 23. Automatic back door control module 24. Side radar LH
25. Side radar RH
JSMIA0343ZZ
Revision: 2010 May2011 QX56

LAN
SYSTEMLAN-27
< SYSTEM DESCRIPTION > [CAN]
C
D
E
F
G H
I
J
K L
B A
O P
N
SYSTEM
CAN COMMUNICATION SYSTEM
CAN COMMUNICATION SYSTEM : CAN
System Specification ChartINFOID:0000000006220532
Determine CAN system type from the following specification chart.
NOTE:
Refer to LAN-18, "
Trouble Diagnosis Procedure" for how to use CAN system specification chart.
×: Applicable
VEHICLE EQUIPMENT IDENTIFICATION INFORMATION
NOTE:
Body type Wagon
Axle 2WD 4WD
Engine VK56VD
Transmission A/T
Brake control VDC
ICC system ××
CAN system type 1 2 3 4 CAN communication unit
ECM ××××
Transfer control unit ××
ABS actuator and electric unit (control unit) ××××
TCM ××××
Air bag diagnosis sensor unit ××××
AFS control unit ××
AV control unit ××××
BCM ××××
CAN gateway ××
Data link connector ××××
A/C auto amp. ××××
Combination meter ××××
Steering angle sensor ××××
Low tire pressure warning control unit ××××
IPDM E/R ××××
Driver seat control unit ××××
Pre-crash seat belt control unit (driver side) ××
Air levelizer control module ××××
ADAS control unit ××
Automatic back door control module ××××
ITS communication unit
ADAS control unit ××
Side radar RH ××
Side radar LH ××
Lane camera unit ××
Accelerator pedal actuator ××
ICC sensor ××
Revision: 2010 May2011 QX56

LAN-28
< SYSTEM DESCRIPTION >[CAN]
SYSTEM
Check CAN system type from the vehicle shape and equipment.
CAN COMMUNICATION SYSTEM : CA
N Communication Signal ChartINFOID:0000000006220533
Refer to LAN-17, "How to Use CAN Communication Signal Chart" for how to use CAN communication signal
chart.
T: Transmit R: Receive
1. ICC sensor
A. With ICC system
JSMIA0342ZZ
Signal nameECM
4WD
ABS
TCM
A-BAG
AFSAV
BCM
CGW
HVAC
M&A
STRG
TPMS
IPDM-E ADP
PSB
E-SUS ICC
PWBD
A/C compressor request
signal TR
Accelerator pedal position
signal TRRR
R
ASCD OD cancel request
signal TR
ASCD operation signal T R
ASCD status signal T R
Closed throttle position sig-
nal TR
R
Cooling fan speed request
signal TR
Engine and A/T integrated
control signal TR
RT
Engine coolant temperature
signal TRR
Engine restart request sig-
nal TRR
TR
Engine speed signal T R R R R R R R
Engine status signal T R R R
Engine torque signal T R
Fuel consumption monitor
signal TRR
ICC brake switch signal T R
ICC prohibition signal T R
ICC steering switch signal T R
Malfunctioning indicator
lamp signal TR
N idle instruction signal TR
RT
Revision: 2010 May2011 QX56

LAN
SYSTEMLAN-29
< SYSTEM DESCRIPTION > [CAN]
C
D
E
F
G H
I
J
K L
B A
O P
N
Power generation com-
mand value signal
TR
Snow mode signal T R
Stop lamp switch signal T
R
RT
RT R
Wide open throttle position
signal TR
ATP warning lamp signal T R
4WD malfunction signal T R
4WD mode indicator signal T R
4WD warning lamp signal T R
Current 4WD mode signal T R R
A/T shift schedule change
demand signal TR
ABS malfunction signal R T R
ABS operation signal R T R R R
ABS warning lamp signal T R R
Brake warning lamp signal T R
Decel G sensor signal T R
Pressure sensor signal T R
Side G sensor signal T R R
Target throttle position sig-
nal RT
TCS malfunction signal R T R
TCS operation signal R T R
VDC malfunction signal R T R
VDC OFF indicator lamp
signal TR
VDC OFF switch signal T R
VDC operation signal R T R
VDC warning lamp signal T R
Vehicle speed signal RRRRRRT RRRR
RRT R RRRRRR
Yaw rate signal T R
A/T CHECK indicator lamp
signal TR R
Current gear position signal R R T R
Input speed signal R T R
Manual mode shift refusal
signal TR
N range signal T R R
Next gear position signal R T
Output shaft revolution sig-
nal RR T
R
Signal name
ECM
4WD
ABS
TCM
A-BAG AFS
AV
BCM
CGW
HVAC M&A
STRG
TPMS
IPDM-E
ADPPSB
E-SUS ICC
PWBD
Revision: 2010 May2011 QX56

LAN
SYSTEMLAN-31
< SYSTEM DESCRIPTION > [CAN]
C
D
E
F
G H
I
J
K L
B A
O P
N
Meter display signal
TR
RT
Oil pressure switch signal TR
RT
Position light request signal T R R
Rear fog light status signal T R
Rear window defogger con-
trol signal TR
RT
Sleep wake up signal T R R R R R R
Starter control relay signal T R
Starter relay status signal TRR
RT
Starting mode signal T R
Steering lock relay signal TRR
RT
Theft warning horn request
signal TR
Turn indicator signal R T R R
A/C display signal R T
A/C ON signal R T
Ambient temperature signal T R
Blower fan ON signal R T
Distance to empty signal R T
Fuel level low warning sig-
nal RT
Fuel level sensor signal R T
Manual mode shift down
signal RT
Manual mode shift up sig-
nal RT
Manual mode signal R T
Non-manual mode signal R T
Odometer signal R T
Parking brake switch signal R R T R R
Sleep-ready signal RT
RT
RT
Tow mode switch signal R T
Wake up signal RT
RT
Steering angle sensor mal-
function signal RR T R R
Steering angle sensor sig-
nal RR RR T R R
Steering angle speed signal R T R R Signal name
ECM
4WD
ABS
TCM
A-BAG AFS
AV
BCM
CGW
HVAC M&A
STRG
TPMS
IPDM-E
ADPPSB
E-SUS ICC
PWBD
Revision: 2010 May2011 QX56

LAN-58
< DTC/CIRCUIT DIAGNOSIS >[CAN]
MALFUNCTION AREA CHART
SHORT CIRCUIT
ITS Communication CircuitINFOID:0000000006220538
MAIN LINE
BRANCH LINE
Malfunction area Reference
ECM branch line circuit LAN-68, "
Diagnosis Procedure"
Transfer control unit branch line circuitLAN-69, "Diagnosis Procedure"
ABS actuator and electric unit (control unit) branch line circuit LAN-70, "Diagnosis Procedure"
TCM branch line circuit LAN-71, "Diagnosis Procedure"
Air bag diagnosis sensor unit branch line circuitLAN-72, "Diagnosis Procedure"
AFS control unit branch line circuitLAN-73, "Diagnosis Procedure"
AV control unit branch line circuitLAN-74, "Diagnosis Procedure"
BCM branch line circuitLAN-75, "Diagnosis Procedure"
CAN gateway branch line circuit (CAN communication circuit 1)LAN-76, "Diagnosis Procedure"
CAN gateway branch line circuit (CAN communication circuit 2)LAN-77, "Diagnosis Procedure"
Data link connector branch line circuitLAN-78, "Diagnosis Procedure"
A/C auto amp. branch line circuitLAN-79, "Diagnosis Procedure"
Combination meter branch line circuitLAN-80, "Diagnosis Procedure"
Steering angle sensor branch line circuitLAN-81, "Diagnosis Procedure"
Low tire pressure warning control unit branch line circuitLAN-82, "Diagnosis Procedure"
IPDM E/R branch line circuitLAN-83, "Diagnosis Procedure"
Driver seat control unit branch line circuitLAN-84, "Diagnosis Procedure"
Pre-crash seat belt control unit (driver side) branch line circuitLAN-85, "Diagnosis Procedure"
Air levelizer control module branch line circuitLAN-86, "Diagnosis Procedure"
ADAS control unit branch line circuitLAN-87, "Diagnosis Procedure"
Automatic back door control module branch line circuitLAN-88, "Diagnosis Procedure"
Malfunction area Reference
CAN communication circuit (Without ICC system) LAN-94, "
Diagnosis Procedure"
CAN communication circuit 1 (With ICC system)LAN-96, "Diagnosis Procedure"
CAN communication circuit 2 (With ICC system)LAN-98, "Diagnosis Procedure"
Malfunction area Reference
Main line between side radar RH and side radar LH LAN-64, "
Diagnosis Procedure"
Main line between side radar LH and lane camera unitLAN-65, "Diagnosis Procedure"
Main line between lane camera unit and accelerator pedal actu-
atorLAN-67, "Diagnosis Procedure"
Malfunction area Reference
Side radar RH branch line circuit LAN-89, "
Diagnosis Procedure"
Side radar LH branch line circuitLAN-90, "Diagnosis Procedure"
Lane camera unit branch line circuitLAN-91, "Diagnosis Procedure"
Accelerator pedal actuator branch line circuitLAN-92, "Diagnosis Procedure"
ICC sensor branch line circuitLAN-93, "Diagnosis Procedure"
Revision: 2010 May2011 QX56

LAN-72
< DTC/CIRCUIT DIAGNOSIS >[CAN]
A-BAG BRANCH LINE CIRCUIT
A-BAG BRANCH LINE CIRCUIT
Diagnosis ProcedureINFOID:0000000006220548
WARNING:
 Before servicing, turn ignition switch OFF, disco
nnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the air bag diagnosis sensor unit for damage, bend and loose con-
nection (unit side and connector side).
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the main harness.
2.CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Check the air bag diagnosis sensor unit. Refer to SRC-36, "
Work Flow".
Is the inspection result normal?
YES >> Replace the main harness.
NO >> Replace parts whose air bag system has a malfunction.
Revision: 2010 May2011 QX56

LAN
STRG BRANCH LINE CIRCUITLAN-81
< DTC/CIRCUIT DIAGNOSIS > [CAN]
C
D
E
F
G H
I
J
K L
B A
O P
N
STRG BRANCH
LINE CIRCUIT
Diagnosis ProcedureINFOID:0000000006220557
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cabl e from the negative terminal.
3. Check the terminals and connectors of the steer ing angle sensor for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the terminal and connector.
2.CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of steering angle sensor.
2. Check the resistance between the steering angle sensor harness connector terminals.
Is the measurement value within the specification?
YES >> GO TO 3.
NO >> Repair the steering angle sensor branch line.
3.CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the steering angle sensor. Refer to BRC-53, "
Wiring Dia-
gram".
Is the inspection result normal?
YES (Present error)>>Replace the steering angle sensor. Refer to BRC-139, "Removal and Installation".
YES (Past error)>>Error was detected in the steering angle sensor branch line.
NO >> Repair the power supply and the ground circuit.
Steering angle sensor harness connector Resistance (Ω)
Connector No. Terminal No.
M30 5 2 Approx. 54 – 66
Revision: 2010 May2011 QX56