mirror INFINITI QX56 2011 Factory Service Manual

MIR-18
< WIRING DIAGRAM >
DOOR MIRROR SYSTEM
JCLWM5433GB
Revision: 2010 May2011 QX56

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEMMIR-19
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -INFOID:0000000006257227
JCLWM5434GB
Revision: 2010 May2011 QX56

MIR-20
< WIRING DIAGRAM >
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
JCLWM5435GB
Revision: 2010 May2011 QX56

MIR-22
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH
OPEN/CLOSE SWITCH
OPEN/CLOSE SWITCH : Co mponent InspectionINFOID:0000000006257229
1.CHECK OPEN/CLOSE SWITCH
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Check continuity between door mirro r remote control switch terminals.
[Driver side]
[Passenger side]
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace door mirror remote control switch.
Door mirror remote control switch
Condition Continuity
Te r m i n a l
12 10
Open/close switchOPEN
Existed
13 8
12 8
CLOSE
13 10
Door mirror remote control switch Condition Continuity
Te r m i n a l
12 11
Open/close switchOPEN
Existed
13 9
12 9
CLOSE
13 11
Revision: 2010 May2011 QX56

REVERSE INTERLOCK DOOR MIRROR DOES NOT OPERATE
MIR-23
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
SYMPTOM DIAGNOSIS
REVERSE INTERLOCK DOOR MI RROR DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000006257230
1.CHECK DOOR MIRROR (MANUAL FUNCTION)
Check door mirror function with door mirror remote control switch.
Refer to ADP-126, "
DOOR MIRROR : Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK DTC
Check DTC for TCM.
Refer to TM-78, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> GO TO 1.
Revision: 2010 May2011 QX56

MIR-30
< REMOVAL AND INSTALLATION >
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded ViewINFOID:0000000006257234
With rain sensor models
Without rain sensor models
Removal and InstallationINFOID:0000000006257235
WITH RAIN SENSOR MODELS
JMLIA0907GB
1. Rain sensor cover 2. Windshield glass 3. Rain sensor
4. Mirror base 5. Harness connector 6. TORX bolt
7. Inside mirror : Pawl
Refer to GI-4, "
Components" for symbols in the figure.
JMLIA0906GB
1. Windshield glass 2. Mirror base 3. Harness connector
4. TORX bolt 5. Inside mirror 6. Inside mirror cover
Refer to GI-4, "
Components" for symbols in the figure.
Revision: 2010 May2011 QX56

INSIDE MIRRORMIR-31
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
Removal
1. Disengage rain sensor cover fixing pawls with a remover tool to remove.
2. Disconnect harness connector from inside mirror.
3. Loosen TORX bolt and slide inside mirror upward to remove.
Installation
Install in the reverse order of removal.
WITHOUT RAIN SENSOR MODELS
Removal
1. Remove inside mirror cover.
2. Disconnect harness connector from inside mirror.
3. Loosen TORX bolt and slide inside mirror upward to remove.
Installation
Install in the reverse order of removal.
Revision: 2010 May2011 QX56

MIR-32
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
OUTSIDE MIRROR
Exploded ViewINFOID:0000000006257236
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and InstallationINFOID:0000000006257237
REMOVAL
1. Remove front door finisher and door mirror corner cover. Refer to INT-14, "Removal and Installation".
2. Disconnect door mirror assembly harness connector.
3. Remove door mirror mounting nuts, and then remove door mirror assembly.
1. Door mirror cover 2. Glas s mirror 3. Actuator assembly
4. Connector 5. Door mirror co ver 6. Side camera finisher
7. Around view camera 8. Side turn signal lamp 9. Housing
10. Bracket 11. Power fold unit 12. Base cover
13. Puddle lamp 14. Base : Clip
: Pawl
JMLIA1144ZZ
Revision: 2010 May2011 QX56

OUTSIDE MIRRORMIR-33
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Perform camera image calibration (with side camera models). Refer to AV-112, "
Work Procedure".
DOOR MIRROR ASSEMBLY : Disassembly and AssemblyINFOID:0000000006257238
DISASSEMBLY
1. Remove door mirror assembly from front door panel. Refer to MIR-32, "DOOR MIRROR ASSEMBLY :
Removal and Installation".
2. Remove glass mirror. Refer to MIR-35, "
GLASS MIRROR : Removal and Installation".
3. Remove door mirror cover. Refer to MIR-36, "
DOOR MIRROR COVER : Removal and Installation".
4. Remove actuator. 1. Remove actuator (1) fixing screws (A).
2. Disconnect the harness connec tors behind the actuator.
NOTE:
Disconnect the harness connector (B) of automatic driving posi-
tion system (2) if equipped.
5. Remove side camera finisher assembly (1). 1. Remove side camera finisher fixing screw (A).
JMLIA0910ZZ
JMLIA0911ZZ
JMLIA0912ZZ
Revision: 2010 May2011 QX56

MIR-34
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
2. Disconnect harness connector (B), and remove screws (C)and pawl (D) fixing the side camera finisher (1) to housing.
3. Remove side turn signal lamp fixing screws (E), and then remove side turn signal lamp.
NOTE:
Pull slightly side camera finisher (1) covering side turn sig-
nal lamp bottom screw.
4. Remove side camera finisher assembly.
5. Remove around view camera. Refer to AV-233, "
Removal and Installation".
6. Remove all the harness connector terminal from the connector. NOTE:
Write a short note to describe connector terminal layout before starting operation.
7. Remove base. 1. Remove base cover. Remove base cover fixing pawls with a flat-bladed screw-
driver (A) wrapped into a tape.
CAUTION:
Apply protective tape (B) aro und the base to protect the
surface from damage.
2. Remove puddle lamp. Refer to INL-79, "
Removal and Installation".
3. Remove base mounting bolts located under base cover.
4. Remove base.
8. Remove the fixing screws (A), and then remove power fold unit and bracket from housing.
JMLIA0913ZZ
JMLIA0914ZZ
: Pawl
JMLIA1146ZZ
JMLIA0923ZZ
Revision: 2010 May2011 QX56