lock ISUZU KB P190 2007 Workshop Repair Manual
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2007, Model line: KB P190, Model: ISUZU KB P190 2007Pages: 6020, PDF Size: 70.23 MB
Page 2771 of 6020
Engine Mechanical – V6 Page 6A1–292
6 Torque Wrench Specifications
ATTENTION
„
„ „
„
Fasteners must be replaced after loosening.
Fasteners either have micro encapsulated sealant applied or incorporate a mechanical thread lock and
should only be re-used once. If in doubt, replacement is recommended.
Oil Pan Drain Plug ................................................................................ 25.0 Nm
Oil Filter Adaptor Attaching Bolt ................................................ 20.0 – 26.0 Nm
Oil Level Indicator Tube Attaching Bolt........................................ 8.0 – 12.0 Nm
Accessory Drive Belt Idler Pulley Attaching Bolt................................... 50.0 Nm
Accessory Drive Belt Tensioner Attaching Bolt .................................... 50.0 Nm
Power Steering Reservoir Bracket Attaching Screw.............................. 9.0 Nm
Power Steering Pump Bracket Attaching Bolt ........................... 49.0 – 67.0 Nm
Upper Intake Manifold to Lower Intake Manifold Attaching Bolt ........... 23.0 Nm
Upper Intake Manifold to Cylinder Head Attaching Bolt........................ 23.0 Nm
Lower Intake Manifold to Cylinder Head Attaching Bolt........................ 23.0 Nm
Fuel Injector Wiring Harness Bracket Attaching bolt .............................. 9.0 Nm
Exhaust Manifold to Cylinder Head Attaching Bolt ..................... 17.0 - 23.0 Nm
Exhaust Manifold Heat Shield Attaching Bolt ............................... 8.0 - 12.0 Nm
Battery Harness Ground Terminal Attaching Nut ................................. 13.0 Nm
Camshaft Cover Attaching Bolt ................................................... 8.0 – 12.0 Nm
Engine Ground Connector Bolt............................................................. 10.0 Nm
Engine Wiring Harness Former Attaching Bolt .......................... 12.0 – 16.0 Nm
„ Crankshaft Balancer Assembly Attaching Bolt:
Stage 1 ..................................................................................... 90.0 –110.0 Nm
Stage 2 ....................................................................................................... 150 °
Engine Front Cover Assembly Attaching Bolt ............................ 20.0 – 26.0 Nm
Camshaft Intermediate Driveshaft Sprocket Attaching Bolt ....... 58.0 – 72.0 Nm
Secondary Timing Chain Guide Attaching Bolt.......................... 20.0 – 26.0 Nm
Secondary Timing Chain Shoe Attaching Bolt ........................... 20.0 – 26.0 Nm
Secondary Timing Chain Tensioner Attaching Bolt ................... 20.0 – 26.0 Nm
Primary Timing Chain Upper Guide Attaching Bolt.................... 20.0 – 26.0 Nm
Primary Timing Chain Tensioner Attaching Bolt ........................ 20.0 – 26.0 Nm
Oil Pump Assembly Attaching Bolt ............................................ 20.0 – 26.0 Nm
Camshaft Sprocket Attaching Bolt ............................................. 49.0 – 67.0 Nm
Exhaust Camshaft Sprocket Attaching Bolt ............................... 49.0 – 67.0 Nm
Camshaft Bearing Cap Attaching Bolt ......................................... 8.0 – 12.0 Nm
Cylinder Head Threaded Plug .............................................................. 31.0 Nm
„ Cylinder Head M11 Attaching Bolt:
Stage 1 ...................................................................................... 40.0 – 50.0 Nm
Stage 2 ....................................................................................................... 120 °
„ Cylinder Head M8 Attaching Bolt:
Stage 1 ...................................................................................... 12.0 – 18.0 Nm
Stage 2 ......................................................................................................... 60 °
Engine Mount Bracket to Cylinder Block Attaching Bolt ............ 43.0 – 57.0 Nm
Engine Mount to Bracket Attaching Nut ..................................... 70.0 – 90.0 Nm
Engine Mount to Frame Attaching Nut....................................... 44.0 – 60.0 Nm
Engine Lift Bracket Attaching Bolt .......................................... 58.0 – 72.0.0 Nm
Knock Sensor Attaching Nut................................................................. 23.0 Nm
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2772 of 6020
Engine Mechanical – V6 Page 6A1–293
Power Steering High Pressure Line Attaching Bolt ..................... 8.0 – 12.0 Nm
Power Steering High Pressure Line Flare Nut ........................... 25.0 – 35.0 Nm
Steering Gear Housing Mounting Nut:
Stage 1 ................................................................................................. 60.0 Nm
Stage 2 ................................................................................................40° – 50°
Oil Suction Pipe Attaching Bolt ............................................................. 10.0 Nm
Crankshaft Oil Deflector Attaching bolt................................................. 10.0 Nm
Oil Level Sensor ................................................................................... 20.0 Nm
Oil Pan to Cylinder Block Attaching Bolt .................................... 20.0 – 26.0 Nm
Oil Pan to Crankshaft Rear Oil Seal Housing Attaching Bolt ........ 8.0 - 12.0 Nm
„ Flexplate Attaching Bolt:
Stage 1 ...................................................................................... 26.0 – 34.0 Nm
Stage 2 ......................................................................................................... 45 °
Crankshaft Rear Oil Seal Housing Attaching Bolt........................ 8.0 – 12.0 Nm
„ Connecting Rod Cap Attaching Bolt:
Stage 1 ................................................................................................. 30.0 Nm
Stage 2 ................................................................................ Loosen Completely
Stage 3 ................................................................................................. 25.0 Nm
Stage 4 ....................................................................................................... 110 °
Crankshaft Bearing Cap Remover Nut ................................................. 11.0 Nm
„ Crankshaft Main Bearing Cap Inboard Attaching Bolt:
Stage 1 ................................................................................................. 20.0 Nm
Stage 2 ......................................................................................................... 80 °
„ Crankshaft Main Bearing Cap Outboard Attaching Bolt:
Stage 1 ................................................................................................. 15.0 Nm
Stage 2 ....................................................................................................... 110 °
„ Crankshaft main Bearing Cap Side Attaching Bolt:
Stage 1 ................................................................................................. 30.0 Nm
Stage 2 ......................................................................................................... 60 °
Cylinder Block Threaded Plug .................................................... 27.0 - 35.0 Nm
Oil Jet Attaching Bolt ................................................................... 8.0 – 12.0 Nm
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2773 of 6020
Engine Mechanical – V6 Page 6A1–294
7 Special Tools
Tool Number Illustration Description
E-308 Seal Remover
Previously released.
EN-46101
Spark Plug Tube Seal Guide Set
Used to protect the spark plug lip seals when installing the
camshaft cover to the cylinder head.
EN-46103
Camshaft Actuator Valve Seal Installer
Used to install the camshaft actuator valve seals into the front
cover.
EN-46105 –
1 and 2
Camshaft Locking Tool Set
Used to retain camshaft position during timing chain or
camshaft actuator replacement.
EN-46106
Flexplate Holding Tool
Used to retain crankshaft position during valve-train overhaul
and harmonic balancer removal.
EN-46108
Timing Chain Retention Tool Set
Used to retain timing chain tension during camshaft and
sprocket removal.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2774 of 6020
Engine Mechanical – V6 Page 6A1–295
Tool Number Illustration Description
EN-46109
Engine Front Cover / Oil Pan / Crankshaft Rear Oil Seal
Housing Installation Guide Pins
Used to align the engine front cover/oil pan/crankshaft rear oil
seal housing during engine assembly.
EN-46110
On-vehicle Valve Spring Compressor
Used to remove valve springs with the cylinder heads
assembled to the cylinder block.
EN-46111
Crankshaft Rotation Socket
Used to rotate the crankshaft during engine overhaul.
EN-46112
Timing Chain Tensioner Retraction Springs
Used to retain the timing chain tensioner plunger within the
tensioner bore during assembly of timing chains to engine.
EN-46114
Engine Lift Brackets
Used in conjunction with commercially available lifting
equipment to lift engine.
EN-46116
Valve Stem Seal Remover / Installer
Used to remove/install the valve stem seals.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2776 of 6020
Engine Mechanical – V6 Page 6A1–297
Tool Number Illustration Description
J-29184
Crankshaft Front Oil Seal Installer
J-36648-A
Oil Pressure Gauge Adaptor
j-41816 three legged puller
J-41818
Main Bearing Cap Removal Tool
Used in conjunction with J-6125-1B to remove the main
bearing caps from the cylinder block during engine
disassembly procedures.
J-41998-B
Crankshaft Balancer Installer
J-42385-2000
Thread Insert Kit
Used to repair damaged threads during engine overhaul.
J-42385-700
High Feature Thread Repair Kit
Used to repair damaged threads during engine overhaul.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2777 of 6020
Engine Mechanical – V6 Page 6A1–298
Tool Number Illustration Description
J-45027
Tensioner Tool
Used to reset the timing chain tensioner plunger.
J-6125-1B
Slide Hammer
Used in conjunction with J-41818 to remove the main bearing
caps from the cylinder block during engine disassembly.
J-8062
Valve Spring Compressor
Used in conjunction with EN-46119 to remove valve springs
with the engine disassembled.
J-8087
Cylinder Bore Gauge
Commercial equivalent also available
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2778 of 6020
Engine Mechanical – V6 Page 6A1–1
Page 6A1–1
Section 6A1
Engine Mechanical – V6
ATTENTION
Before performing any service operation or other procedure described in this Section, refer to 1.1 WARNING,
CAUTION and NOTES for correct workshop practices with regard to safety and/or property damage.
1 General Information ............................................................................................................ ...................8
MY06 Update .................................................................................................................... ......................................8
1.1 WARNING, CAUTION and NOTES .................................................................................................... ...................8
Definition of WARNING, CAUT ION and NOTE Statements ............................................................................. ....8
WARNING defined ................................................................................................................ .............................8
CAUTION defined ................................................................................................................ ..............................8
NOTE defined................................................................................................................... ..................................9
1.2 Engine Components .............................................................................................................. ..............................10
Major Component Assemblies............................................................................................................................ 10
Intake Manifold Assembly ....................................................................................................... ............................11
Engine Front Cover............................................................................................................. .................................12
Camshaft Timing Components ..................................................................................................... ......................13
Camshaft Cove r Assembly........................................................................................................ ..........................14
Cylinder Head Assembly ......................................................................................................... ............................15
Oil Pump ....................................................................................................................... ........................................16
Engine Block Assembly .......................................................................................................... ............................17
Pistons, Rings, Bearing and Connecting Rod ..................................................................................... ..............18
Oil Pan Assembly............................................................................................................... ..................................19
Oil Filter Assembly ............................................................................................................ ..................................20
1.3 Engine Serial Number........................................................................................................... ...............................21
1.4 Engine Construction............................................................................................................ ................................22
Cylinder Block ................................................................................................................. .....................................22
Cylinder Heads ..................................................................................................................................................... 22
Crankshaft ..................................................................................................................... .......................................23
Pistons, Pins and Connecting Rods .............................................................................................. ....................23
Camshaft Driv e System ....................................................................................................................................... 24
1.5 Engine Lubrication System .................................................................................................................................25
Lubrication Description........................................................................................................ ...............................25
1.6 Service Notes .................................................................................................................. .....................................26
Cleanliness and Care........................................................................................................... ................................26
Replacing Engine Gaskets .................................................................................................................................. 26
Re-Using Gaskets and Applying Sealants......................................................................................... ...............26
Separating Co mponents................................................................................................................................... 26
Cleaning Gasket Surfaces ................................................................................................................................ 26
Assembling Components ................................................................................................................................. 26
Use of Room Temperature Vulcanising and Anaerobic Sealer....................................................................... .27
Room Temperature Vu lcanising Sealer............................................................................................ ................27
Anaerobic Sealer ............................................................................................................... ...............................27
Pipe Joint Compound ............................................................................................................ ...........................28
Separating Parts ............................................................................................................... ...................................28
Tools and Equipment ............................................................................................................ ..............................28
Fasteners .............................................................................................................................................................. 29
Clamp Load ..................................................................................................................... .................................29
Torque Angle and Torque to Yield Fastener s................................................................................................... 29
2 Diagnosis ...................................................................................................................... ........................30
2.1 Engine Diagnosis ............................................................................................................... ..................................30
2.2 Symptoms ....................................................................................................................... .....................................31
Strategy Based Diagnosis................................................................................................................................... 31
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2783 of 6020
Engine Mechanical – V6 Page 6A1–6
Page 6A1–6
Reassemble ........................................................................................................................................................ 257
Reinstall .............................................................................................................................................................. 257
4.3 Flexplate Assembly ............................................................................................................. ..............................259
Remove ............................................................................................................................................................... 259
Clean................................................................................................................................................................... 259
Inspect ........................................................................................................................ ........................................260
Reinstall .............................................................................................................................................................. 260
4.4 Crankshaft Rear Seal and Plate Assembly ........................................................................................ ..............262
Remove ............................................................................................................................................................... 262
Reinstall .............................................................................................................................................................. 263
4.5 Pistons, Pins, Rings, Connecting Rods and Big-end Bearings ..................................................................... 265
Remove ............................................................................................................................................................... 265
Disassemble ....................................................................................................................................................... 268
Clean and Inspect .............................................................................................................. ................................269
Piston Cleaning Procedure...................................................................................................... .......................269
Piston Inspection Procedure .................................................................................................... ......................269
Piston Measurement ............................................................................................................. .........................270
Piston Ring Measurement ........................................................................................................ ......................271
Connecting Rod Cleaning Procedure .............................................................................................. ...............272
Connecting Rod Visual Inspection Procedure ..................................................................................... ...........272
Connecting Rod Meas urement Procedure ........................................................................................... ..........272
Reasse mble ........................................................................................................................................................ 274
Piston and Piston Pin ..................................................................................................................................... 274
Piston Ring .................................................................................................................... .................................275
Connecting Rod Bearing ................................................................................................................................ 276
Reinstall .............................................................................................................................................................. 277
Piston Connecting Rod and Connecting Rod Bearing Inst allation .................................................................. 277
Connecting Rod Bearing Clearance Measurement Procedure....................................................................... 278
Connecting Rod Final Assembly Procedure ........................................................................................ ...........279
4.6 Crankshaft and Ma in Bearings ................................................................................................... ......................281
Crankshaft End Play Measurement ................................................................................................ ..................281
Remove ............................................................................................................................................................... 281
Crankshaft Bearing............................................................................................................. ............................283
Clean and Inspect .............................................................................................................. ................................283
Crankshaft and Main Bearing Cleaning ........................................................................................... ...............283
Crankshaft and Main Bear ing Visual Inspection .................................................................................. ...........284
Crankshaft Main B earing Inspection............................................................................................. ..................285
Crankshaft M easurement ......................................................................................................... ......................286
Reinstall .............................................................................................................................................................. 288
Crankshaft Bearing Installation Procedure ...................................................................................... ...............288
Crankshaft Main Bearing Clearance Measurement .................................................................................. ......289
Crankshaft Final Instal lation Procedure........................................................................................ ..................291
4.7 Cylinder Block ................................................................................................................. ...................................293
Disassemble ....................................................................................................................................................... 293
Clean................................................................................................................................................................... 297
Inspect ........................................................................................................................ ........................................297
Visual Inspection .............................................................................................................. ..............................297
Measuring Cylinder Bore Diameter ............................................................................................... .................297
Measuring Cylinder Bore Taper.................................................................................................. ....................298
Measuring Cylinder Bo re Out-of-Round ........................................................................................... ..............298
Deck Flatness Inspection ............................................................................................................................... 298
Reassemble ........................................................................................................................................................ 299
4.8 Thread Repairs ................................................................................................................................................... 303
General Information ............................................................................................................ ...............................303
General Thread Repair .......................................................................................................... ............................304
Main Bearing Cap Bolt Hole Thread Repair ....................................................................................... ..............310
Cylinder Head Bolt Hole Thread Repair .......................................................................................... .................315
4.9 Thread Repair Specifications................................................................................................... .........................322
Left-hand Cylinder Head Camshaft Cover Face .................................................................................... ..........322
Left-hand Cylinder H ead Front Face ............................................................................................. ...................323
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2784 of 6020
Engine Mechanical – V6 Page 6A1–7
Page 6A1–7
Left-hand Cylinder Head Intake Face ............................................................................................ ...................324
Left-hand Cylinder H ead Exhaust Face ........................................................................................... ................325
Left-hand Cylinder H ead Rear Face .............................................................................................. ...................326
Right-hand Cylinder Head Camshaft Cover Face ................................................................................... ........327
Right-hand Cylinder Head Front Face............................................................................................ ..................328
Right-hand Cylinder Head Intake Face ........................................................................................... .................329
Right-hand Cylinder He ad Exhaust Face .......................................................................................... ...............330
Right-hand Cylinder Head Rear Face ............................................................................................. ..................331
Engine Block Front ............................................................................................................................................ 332
Engine Block Left-hand Side .................................................................................................... ........................333
Engine Block Ri ght-hand Side ................................................................................................... .......................334
Engine Block Rear .............................................................................................................. ...............................335
Engine Block Bottom......................................................................................................................................... 336
Engine Block Left-hand Deck Face ............................................................................................... ...................337
Engine Block Righ t-hand Deck Face.............................................................................................. ..................338
Engine Front Cover............................................................................................................. ...............................339
Upper Intake Manifold Top ...................................................................................................... ..........................340
Upper Intake Mani fold Front .................................................................................................... .........................341
Upper Intake Ma nifold Rear..................................................................................................... ..........................342
Lower Intake Ma nifold Top...................................................................................................... ..........................343
Oil Pan Front .................................................................................................................. ....................................344
Oil Pan Rear........................................................................................................................................................ 345
Oil Pan Bottom ................................................................................................................................................... 346
5 Specifications .....................................................................................................................................347
6 Torque Wrench Specifications................................................................................................... .......351
7 Special Tools .................................................................................................................. ....................353
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 2785 of 6020
Engine Mechanical – V6 Page 6A1–8
Page 6A1–8
1 General Information
The HFV6 engine features a closed vee, deep skirt die cast aluminium cylinder block with cast iron cylinder liners,
internally balanced crankcase, full length wa ter jackets and six bolt main bearing caps.
The cylinders are arranged in two banks of three with a 60 degree included angle between the two banks.
The right-hand bank of cylinders consists of number 1-3-5
cylinders and the left-hand bank of cylinders consists of
number 2-4-6.
The engine firing order is 1-2-3-4-5-6.
Each aluminium cylinder head is fitted with hardened valve
seats and four valves per cylinder: two intake and two
exhaust.
The valves are operated by two camshafts (DOHC) per
cylinder bank, one each for intake and exhaust valves.
The crankshaft is manufactured from forged steel. A reluctor
wheel is pressed in place onto the rear of the crankshaft for
the crankshaft position sensor.
The connecting rods are m anufactured from powdered
metal and the rod cap is separ ated during the manufacturing
process using the fractured me thod. This creates a stronger,
visually seamless rod to cap union.
Figure 6A1 – 1
MY06 Update
Throughout this Section, reference is made to 'MY06 Update' or 'Excluding MY06 Update'.
Vehicles manufactured post 14th Marc h 2007 are fitted with an updated version of the HFV6 engine. This engine
features a different timing chain, and as a result different sprocket teeth. This change also introduces the use of a new
special tool to assist in the serviceab ility of replacing the engine timing components.
All service procedures and descriptions specific to this update variation are qualified as 'MY06 Update'.
1.1 WARNING, CAUTION and NOTES
This Section contains various WARNING S, CAUTIONS and NOTE statements that y ou must observe carefully to reduce
the risk of death or injury during servic e, repair procedures or vehicle operation. Incorrect service or repair procedures
may damage the vehicle or cause operat ional faults. WARNINGS, CAUTION and NOTE statements are not exhaustive.
HOLDEN LTD can not possibly warn of a ll the potentially hazardous consequences of failure to follow these instructions.
Definition of WARNING, CAUTION and NOTE Statements
Diagnosis and repair procedures in this Section contain both general and specific WARNING, CAUTION and NOTE
statements. HOLDEN LTD is dedicated to the presentation of service information that helps the technician to diagnose
and repair the systems necessary for proper operation of the vehicle. Certain procedures may present a hazard to the
technician if they are not followed in the reco mmended manner. WARNING, CAUTION and NOTE statements are
designed to help prevent these hazards from o ccurring, but not all hazards can be foreseen.
WARNING defined
A WARNING statement immediately precedes an operating procedure or maint enance practice which, if not correctly
followed, could result in death or injury . A WARNING statement alerts you to ta ke necessary action or not to take a
prohibited action. If a WARNING statement is ignored, the following consequences may occur:
• Death or injury to the technician or other personnel working on the vehicle,
• Death or injury to other people in or near the workplace area, and / or
• Death or injury to the driver / or passenger(s) of the vehicle or other people, if the vehicle has been improperly
repaired.
CAUTION defined
A CAUTION statement immediately prec edes an operating procedure or maintenance practice which, if not correctly
followed, could result in damage to or destruction of equi pment, or corruption of data. If a CAUTION statement is
ignored, the following consequences may occur:
• Damage to the vehicle,
• Unnecessary vehicle repairs or component replacement,
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007