key battery ISUZU TROOPER 1995 Workshop Manual

REAR WHEEL ANTILOCK BRAKE SYSTEM 5A3-15
CHART D
Rr. ABS and Brake Lights Flashing
• TURN THE IGNITION KEY TO THE OFF POSITION, AND DISCONNECT THE EBCM HARNESS CONNECTOR FROM EBCM AND IGN. KEY ON CHECK FOR VOLTAGE AT PIN {13) OF EBCM HARNESS CONNECTOR AND CHASSIS GROUND WHILE
SHAKING THE BODY HARNESS AND REAR BODY HARNESS.
REPAIR THE HARNESS FOR OPEN CIRCUIT, AND RECHECK • DISCONNECT BATTERY, AND CHECK FOR RESISTANCE AT PIN {7) OF THE EBCM HARNESS CONNECTOR AND CHASSIS GROUND WHILE SHAKING THE BODY
HARNESS AND REAR BODY HARNESS.
THE SYSTEM.
•
CHECK FOR RESISTANCE AT PIN {15) OF EBCM HARNESS
CONNECTOR, AND CHASSIS GROUND WHILE SHAKING THE BODY HARNESS AND REAR BODY HARNESS.
REPAIR OPEN CIRCUIT
IN WIRE TO PIN {15) CONNECTOR, AND RECHECK THE SYSTEM.
EBCM = Electronic Brake Control Module

5A4-10 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
TECH 1 TOOL
TECH 1 is an effective tool for the diagnosis of
electrical fault of Antilock Brake System (ASS) and
system check.
Although you can completely
diagnose the system without a TECH 1, using the
tool is quicker. In the following procedures, the
!TECH 11 symbol shows where the TECH 1 is used.
The
t::nettll symbol means the tool is not used.
1. WHAT CAN BE DONE WITH TECH 1
ON TECH 1
TECH 1 is a hand-held tester (Fig. 5A4-4).
Connected
to the Data Link Connector (DLC)
installed in the vehicle, it communicates with
ABS control unit (EBCM), thereby conducting
various diagnoses and tests.
Fig. 5A4-4
For this
vehicle, use ISUZU '90-'94
TRANSMISSION/ASS cartridge.
TECH 1 can check the following items:
(1) Input values of EBCM sensors and
switches, and
working conditions of
solenoid valves.
(2) Diagnostic Trouble Code (DTC) No.
(3) Incoming/outgoing data records.
(4) The function of ABS through the
operation
of the motor and solenoid
valves.
(5) Clearing DTCs stored in EBCM.
How to connect TECH 1 with the vehicle (Fig.
5A4·5, 5A4-6)
(1) Insert the program cartridge (TK02500B-1)
securely
into the TECH 1 main unit (J-38770-1).
(2) Attach the adapter to the cable.
(3) Plug the ISUZU 3-pin adapter (T A-02279-8) into
the adapter.
(4) Insert one end of the power plug into the TECH
1 and the other end into the cigarette lighter of
the vehicle.
The power plug may as well be coupled
directly
to the battery using the battery cable
adapter (J-38770-4).
(5) Turn the ignition key OFF, and connect TECH 1
with DLC (Orange colored).
Fig. 5A4-5
Data link Connector (Orange)
Fig. 5A4-6

4-WHEEL ANTILOCK BRAKE SYSTEM (ABS) 5A4-21
MODE F5: ACTUATOR TEST
This mode is used to exercise the ABS system actuators and make sure they operate normally. Prior to the
test, pay attention
to the cautions below. (When checking the solenoid valve system, be sure to jack up the
vehicle.)
w CAUTION:
• Before testing, be sure that the brakes work normally.
• Make sure that the battery is fully charged.
Conduct the test
by two persons (A TECH 1 operator and a vehicle checker).
• Be sure to start actuator test with the engine stopped.
• Before testing, make sure that electrical trouble, if any, has been completely repaired. Conducting
tests
of ABS actuator with electrical circuit problem remaining uncorrected could damage the
control unit.
Selection Procedure:
SELECT MODE FO:DATA LIST
*
F5:ACTUATOR TEST
IUiJ
SELECT ACTUATOR * P. MOTOR RELAY FL SOL. VALVE
FR SOL. VALVE REAR SOL. VALVE
ABS W/L
----> Refer to CD
----> Refer to ®
----> Refer to @ ----> Refer to @
----> Refer to ®
NOTE:
F5; Actuator test procedure, the systems Q) to @
mentioned on the left can be checked four times
continuously as each system is checked once.
When checking more than
four times continuously,
the fifth check
must be started with a break of 10
minutes or more after the fourth to protect ABS
pump motor.
Select the desired test
by operating !I] 1[!] keys and press I ENT I key.

5A4-50 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
CHART B-1
WITH THE KEY IN THE ON POSITION (BEFORE STARTING THE ENGINE),
WARNING LIGHT
{W/L) IS NOT ACTUATED.
IS W/L FUSE C-10 DISCONNECTED? j
I
IS W/L BURNT OUT? I
I
• TURN IGNITION OFF
• REMOVE EBCM CONNECTOR AND CONNECT PINOUT BOX
• TURN THE KEY ON AND MEASURE VOLTAGE BETWEEN TERMINAL 29 AND 10
I
I
BATTERYVOLTAGE I
I
CHECK CONTINUITY BETWEEN PINOUT BOX I TERMINALS 10, 20 AND 34 AND BODY GROUND
l
I CONTINUITY I
I • CHECK HARNESS FOR SUSPECTED DISCONNECTION I • NO FAULT FOUND: REPLACE EBCM
I
I
DISCONNECTED I
I L REPLACE FUSE J
I L DISCONNECTED J
I I REPLACE W/L BULB I
I
I
LOWVOLTAGE I
I
I
REPAIR HARNESS AND CONNECTOR I
I
I
NO CONTINUITY I
I I REPAIR HARNESS AND CONNECTOR I
•

4-WHEEL ANTILOCK BRAKE SYSTEM (ABS) 5A4-53
CHART B-4 ~I
POWER VOLTAGE DROP (DIAGNOSTIC TROUBLE CODE 15)
INSPECT BATTERY VOLTAGE I (BATTERY CAPACITY CHECKI
I
$ ~
• TURN THE KEY OFF AND CONNECT PINOUT BOX I CHARGE OR REPLACE BATTERY I • TURN THE KEY ON AND MEASURE VOLTAGE BETWEEN PINOUT BOX TERMINAL 1 AND 10
I
I
l
HIGHER THAN 10V I I LOWER THAN 10V I
I I
• CHECK HARNESS/CONNECTOR FOR SUSPECTED I REPAIR HARNESS OR CONNECTOR l DISCONNECTION . FAULT FOUND:
REPAIR, AND PERFORM SYSTEM
SELF-CHECK
• NO FAULT FOUND: REPLACE EBCM

5A4-58 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
CHART B-8 I):Eeti((l
HYDRAULIC UNIT (HU) PUMP MOTOR AND MOTOR RELAY CIRCUIT ~
(DIAGNOSTIC TROUBLE CODE 32)
• WITH THE KEY TURNED OFF, CONNECT PINOUT BOX
• MEASURE RESISTANCE BETWEEN TERMINALS 17 AND28
I 70n-9on I I OTHER THAN 70n-9on I
I
CHECK CONTINUITY BETWEEN TERMINAL 141 AND10 I MEASURE RESISTANCE BETWEEN HU CONNECTORS I C34-6 AND C34-11
I
I I I
CONTINUITY j NO CONTINUITY j 1 70(l-9ooJ I OTHER THAN 70n-9on I
I I I REMOVE HU CONNECTOR CHECK CONTINUITY I REPAIR HARNESS BB07 I I REPLACE HU I AND CHECK CONTINUITY BETWEEN HU OR BB08 BETWEEN PINOUT BOX
CONNECTOR C33-3 TERMINAL 14 AND 10 AND BODY GROUND
I
I
I CONTINUITY I NO CONTINUITY j
I I REPAIR HARNESS BB27, BB06 (OPEN) I • CHECK FOR MOTOR GROUND • FAULT FOUND: REPAIR GROUND
I • NO FAULT FOUND: REPLACE HU
NO CONTINUITY I CONTINUITY J
I MEASURE VOLTAGE REPAIR HARNESS
BETWEEN HU CONNECTOR BB06, BB27
(GND
C33-2 AND BODY GROUND SHORT)
BATTERYVOLTAGE I $
. MOTOR RELAY REPAIR FUSE/HARNESS BETWEEN I ABNORMAL BATTERY AND C33-2/CONNECTOR • REPLACE HU
•

5A4-60 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
CHART B-1 0 [):Ee@]
VALVE RELAY ABNORMALITY (DIAGNOSTIC TROUBLE CODE 45) ~
• WITH THE KEY TURNED OFF, CONNECT PINOUT BOX
• MEASURE RESISTANCE BETWEEN THE TERMINALS 17 AND 27
I 1s-12oo 1 I OTHER THAN 75-1200 J
I
CHECK CONTINUITY
BETWEEN TERMINAL 32 J AND10 I_ REMOVE HU CONNECTOR AND MEASURE I RESISTANCE BETWEEN C34-6 AND C34-10
I
I
I I
CONTINUITY I
NO CONTINUITY/ I75-120n/ I OTHERS I
I I
I
MEASURE
VOLTAGE CHECK CONTINUITY I REPAIR HARNESS/ J I REPLACE HU I
BETWEEN HU HARNESS BETWEEN C34-7 AND CONNECTOR
C33-1 TO BODY GROUND C34-12 ON THE VEHICLE SIDE I
I I CONTINUITY I l NO CONTINUITY I
I I
CHECK CONTINUITY VEHICLE-SIDE
,. HU IS FAULTY J HU CONNECTOR C34-12 AND BODY • REPLACE
HU GROUND
I
I I
CONTINUITY j I NO CONTINUITY I
I I • HARNESS BB12 l REPAIR HARNESS BY02 I OPEN
• REPAIR HARNESS
I BATTERY VOLTAGE j OTHER I
I
• HU VALVE RELAY I REPAIR HARNESS /FUSE BETWEEN I TROUBLE BATTERY AND HU • REPLACE HU
~1111 .. 1 2 3 4 5 617 8 9 101112 =
•

602 - 2 CRANKING SYSTEM
CRANKING CIRCUIT
STARTING SYSTEM
a: co 00
/ +
Battery
50 A
Kew
Position
LOCK
OFF
Key
Removed
ACC Inserted
ON
START Battery
Ignition Battery
Accessories Ignition Starter B1 IG1 B2 ACC IG2 ST
o----o
o----o
oc l---+----+--<0---o
BOA MAIN KEYSW 3WB I I ~~ ...;~-4:) -
IG COIL --------1~-:r uJ----a~ (+) 15A 15A IG COIL ENGINE
GENERATOR IG co :5: ('f)
RELAY; STARTER
3BW r---~
._,()-.L___j -v CLUTCH START SWITCH(M/T)
0.5
BW-I '~ I -0.5 BW ~-+-4~--~~~------~ T I ~ I T : ___________________ ~
.. (NT)
TO AIR CONDITIONING RELAY
Mode SW (NT)
PULLIN
B C\~L _S -/OLD I~ COl~
fl-~ooe--------O<>Ol -----MAGNETIC SWITCH
~-T ------+-----~.
I M
L _______ _
STARTER
Fig. 602-2
•

CRANKING SYSTEM 602 -7
STARTER DOES NOT STOP THOUGH STARTER
SWITCH IS RETURNED TO "ON"
DISCONNECT STARTER SWITCH WIRING CONNECTOR, AND CHECK STARTER SWITCH OPERATION.
KEY
BATTERY IGNITION BATTERY ACCESSORIES IGNITION STARTER
POSITION B1 IG1 B2 ACC IG2 ST
LOCK
OFF
ACC
--- -ON ----------START ----------
THERE MUST BE NO CONTINUITY EXCEPT ABOVE LINES
I
YES I I NO
I
MAGNETIC SWITCH CONTACTS I REPLACE STARTER SWITCH J ARE FUSED AND NOT MOVED, OR A RETURN SPRING IS BROKEN OR DETERIORATED
REPLACE
MAGNETIC SWITCH I

603-2 CHARGING SYSTEM
Battery
+ -...--o ?
,.h,
a: a:l co BOA MAIN . .-. -,., ~
3: co
50 A KEYSW
Key
Position
LOCK
OFF
ACC
ON
START Key
Removed
Inserted
3WB
TO IG COIL
Battery Ignition Battery Accessories Ignition Starter 81 IG1 82 ACC IG2 ST
0 -o
,.... ,....
,.... ,... ,.... ...., ...., ...., ...., ....,
0 ,.... ,.... ,.... 0 ....,
...., ....,
I J
3BY ~ ,.,.
15A 15 A IGCOIL ENGINE
V
"B" termin_a_I _____ _,"IG" terminal
Generator assembly
s_:a_t_er_co __ i_l __ ~~~.-.-~ - Connector
/...-"""\. 0.85BY
B IG
I ~ I ~ A~
-~ ..->--~~ 0.85 WG 0.85 WR To ch arge
' _-: .~:f--<·1'
.~ ~ ~~~~ T ~-r-~ L
. L_ __j
• 1 .... ~ ~ E IC Regulator
L_ Rotor coil ----9---------------'
"L" terminal
warni ng light
0.85WR To ch arge
signal
0.85
WG To Relay, restart
Fig. 603-1
•