belt ISUZU TROOPER 1995 Manual Online

1+•1 REMOVAL
Preparation: Disconnect the battery ground cable
1. Rear end floor trim cover
2. Luggage side cap
3. Luggage side lower cover
• Remove rear side fixing screws and pry trim
cover retainers free from the body panel and
upper trim cover. (Fig. 10-107)
I
w\\1
Fig. 10-107
4. Luggage room light
• Remove luggage room light lens and fixing
~ screws.
Disconnect
luggage room light connector.
5. Rear roof trim cover (Fig. 10-108)
•
Pry trim cover retainers free from the body
panel.
Fig. 10-108
6. Speaker grille (Fig. 10-109)
Fig. 10-109
7. Rear speaker
BODY 10-59
I
I I
~
• Remove the rear speaker fixing screws and
disconnect
the connector.
8. Rear assist grip
• Open the both side covers of the assist grip
and fixing screws. (Fig. 10-110)
Assist grip
Cover
Fig. 10-110
9. Rear seat belt anchor bolt cover and anchor
bolt (Fig. 10-110)

10-60 BODY
Seat belt
Anchor bolt
Seat belt Anchor plate
Fig. 10-111
10. Front seat belt anchor bolt cover and anchor
bolt (Fig. 10-1121
Fig. 10-112
11. Quarter upper trim cover
• Remove the rear side clips of the trim cover
and
pyr trim cover retainers free from the
body panel. (Fig. 10-113)
12. Seat belt anchor plate
Fig. 10-113
I••! INSTALLATION
To install, follow the removal steps in the reverse
order,
noting the following point.
1. Tighten the seat belt anchor bolt to the
specified torque.
~~~ Torque N·m (lb·ftl 39 (29)
•

BODY 10-61
CENTER PILLAR AND ROOF SIDE TRIM COVER (L·W·B ONLY)
Rear quarter upper trim cover
5
1
Fig. 10-114
1+•1 REMOVAL
Preparation: Disconnect the battery ground cable
1. Door sill plate (Front and rear)
2. Center
pillar lower trim cover (Fig. 10-115)
•
Turn up the finisher and pry the trim cover
retainers free
from the body panel, then
slide the trim cover to the downward.
3. Front seat belt anchor bolt cover and anchor
bolt (Fig. 10-104)
4. Center pillar upper trim cover (Fig. 10-116)
•
Turn up the finisher and pry the trim cover
retainers free
from the body panel.
5. Center pillar assist grip
6. Seat belt anchor plate
7. Assist grip (Fig. 10-117)
• Open
the both side assist grip cover and
remove 2
fixing screws.
Front pillar
trim cover
7
(RH only)
Removal steps 1. Door sill plate (Front and rear) 2. Center pillar lower trim cover
3. Front seat anchor bolt cover
and anchor bolt 4. Center pillar upper trim cover 5. Center pillar assist grip
6. Seat belt anchor plate 7. Assist grip 8. Roof side trim cover
Installation steps To install, follow the removal
steps in the reverse order.
Fig. 10-115

1~2BODY
Fig. 10-116
Assist grip
Cover
Fig. 10-117
8. Roof side trim cover (Fig. 10-118)
•
Turn up the finisher and pry the trim cover
retainers free
from the body panel.
~ -~ Roofsidetrim cover
~=1TF "U G 0
Fig. 10-118
l++liNSTALLATION
To install, follow the removal steps in the reverse ~
order, noting the following point.
1. Tighten the seat belt anchor bolts to the
sp~cified torque.
~~~ Torque N·m (lb·ft) I 39 (29)
ROOF SIDE TRIM COVER (S·W·B ONLY)
2. Roof side trim cover
Fig. 10-119
B REMOVAL
1. Assist grip (RH)
• Open the both side covers and remove the
fixing screws. (Fig. 10-117)
2. Roof side tirm cover
• Turn up the finisher and pry the trim cover
retainers free
from body panel. (Fig. 10-120)
Fig. 10-120
l++liNSTALLATION
To install, follow the removal steps in the reverse ~
order.

10-86BODY
FRONT SEAT ASSEMBLY
~ : I
I I
1
,-----
1 0
: t
:~
~~,
I S·W·BI L ______ :J
I
I
I
I
I I I
I
I I
I S·W·B
r-----------
1 q
! 1 I ! ..
~~
I
I
I
I
I I
L _______ S·W·!J
SEATS
3
Fig.
10-181
Removal steps
1. Front cover 2.Rearcover 3. Door sill plate 4. Rear seat foot rest (l·W·B) 5. Riser cover (L·W·B) 6. Seat belt warning connector 7. Front seat assembly
Installation steps
To install, follow the removal steps
in the reverse order.
II

1++1 REMOVAL
Preparation:
Disconnect the battery ground cable
1. Front cover
2. Rear cover
• Remove the cover fixing screw from the rear
inner cover (W/Power seat)
3. Door sill plate
4. Rear seat foot rest (l·W·B)
• Refer to "REAR SEAT FOOT REST" in this
section.
5. Riser cover (L·W·B)
6. Seat belt warning connector (Driver's side
only)
1•!•1 DISASSEMBLY (Fig. 10-182)
Long Wheel Base Spring washer
Bushing
5
Release wire
BODY 10-87
7. Front seat assembly
•
Disconnect the power seat connector (W/
Power seat)
I++IINSTALLATION
To install, follow the removal steps in the reverse
order,
noting the following point.
1. Tighten the front seat assembly fixing bolts to
the specified torque.
~~~ Torque N-m (lb·ft) 40 (30)
2. The longest bolt is installed to the rear inner
side fixing location (W/Power seat)
9a
Fig. 10-182

9a. Guide holder
• Pull the guide holder out from the seat back
assembly.
"-"' 9b. Trim cover
• Remove the trim cover hog rings from the
back side
of seat back.
• With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and frame assembly, remove the
trim cover while turning it up.
9c. Pad
& frame assembly
10. Seat adjuster
• Disconnect the release wire and remove the
fixing
bolts (Fig. 10-188).
•
Remove the seat belt buckle assembly.
11. Height adjuster
11a.
Spacer (W/0 Height adjuster)
12. Seat cushion assembly
12a.
Trim cover
• Remove the trim cover hog rings from the
back side
of the seat cushion .assembly.
• With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and frame assembly, remove the
trim cover while turning it up.
12b. Frame assembly
12c. Pad assembly
Release wire
Fig. 10-188
1•:.1 REASSEMBLY
To reassembly, follow the disassembly steps in the
reverse order, noting the
following point.
1. Tighten the fixing bolts to the specified torque.
• Refer to "TORQUE SPECIFICATIONS" in this
section.
BODY 1o-89

1o-90 BODY
l•!•l DISASSEMBLY (Fig. 10-189)
Short Wheel Base
Spring washer
Front seat belt buckle
assembly
Release
wire
Fig. 10-189
1. Head rest
2.
Reclining knob
3. Dial (W /Height adjuster)
• Remove the side cover fixing screws and
dial lock spring (Fig. 10-190)
4. Side cover
5. Armrest assembly
• Open the armrest fastener and remove the
fixing bolt (Fig. 10-191)
5a. Knob
• Remove the knob fixing screw.
I
________ 1_2a-------~
Fig. 10-190

10-92 BODY
9a. Guide holder
• Pull the guide holder out from the seat back
assembly.
9b. Trim cover
• Remove the trim cover hog rings from the
back side
of seat back.
• With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and
frame assembly, remove the
trim cover while turning it up.
9c. Pad
& frame assembly
10.
Seat adjuster
• Disconnect the release wire and remove the
fixing bolts (Fig. 10-196).
•
Remove the seat belt buckle assembly.
11. Walk-in assembly
11a. Height adjuster
11 b. Spacer (W /0 Height adjuster)
12. Seat cushion
assembly
12a. Trim cover
• Remove the trim cover hog rings from the
back side
of the seat cushion assembly.
•
With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and
frame assembly, remove the
trim cover while turning it up.
12b. Frame
assembly
12c. Pad assembly
Release wire
Fig. 10-196
1•!+1 REASSEMBLY
To reassembly, follow the disassembly steps in the
reverse order,
noting the following point.
1. Tighten the fixing bolts to the specified torque.
• Refer to "TORQUE SPECIFICATIONS" in this
section.
•

10-98 BODY
6. Connecting shaft
7. Seat back assembly
7a. Band hook cover
7b.
Pillow assembly
•
Turn up the seat back trim cover and slit the
pad
from the back around the place where
the lock spring of the guide bush is. Then
insert a
finger through the slit and pull out
the pillow while pressing down on the lock
spring. (Fig. 10-207)
Guide bush
Lock spring
Fig. 10-207
7c.
Armrest assembly
• Turn up the seat back trim cover and remove
the fixing nuts.
7d.
Armrest set bracket
7e. Armrest board
• Remove the fixing clips.
7f. Trim cover
• Remove the trim cover fixing hog rings from
the back side of seat back.
• With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and
frame assembly, remove the
trim cover while turning it up.
7g. Pad
& frame assembly
8. Seat cushion assembly
Sa. Seat lock cover
Sb. Rear seat belt buckle and lock assembly
Sc. Mounting bracket
Sd. Return spring
Se. Spring collar
Sf. Trim cover
• Remove the hog rings and pull the trim
cover out from frame assembly groove.
• With close attention paid to the hog rings
and
wire which connect the trim cover and
the pad and frame assembly, remove the
trim cover while turning it up.
Sg. Frame assembly
Sh. Pad assembly
Si. Stopper rubber
1++1 REASSEMBLY
To reassembly, follow the disassembly steps in the
reverse order, noting the following point.
1. Tighten the reclining device fixing bolts to the
specified torque.
~~~ Torque N-m (lb.ft) 22 (16)
2. Loosen the stopper rubber lock nut and adjust
the stopper so there is no clearance between
the bottom of the stopper and the carpet, while
ensuring the rear seat is firmly locked.
Then tighten the lock nut securely. (Fig. 10-208)
0
0
Lock nut
F Iocr carpet
Fig. 10-208