lamp JAGUAR X308 1998 2.G Workshop Manual

Exterior Lighting - Front Turn Signal Lamp Bulb
Removal and Installation
Removal

1. Applying firm hand pressure to inner end, pivot indicator lamp
assembly for access to outer end.

2. Exercising care to avoid dama ging paintwork, use a small
screwdriver at outer end of lamp, to press and release retaining clip.

3. Withdraw lamp from bumper for access and disconnect harness multiplug.

4. Rotate bulb holder 1/8 turn to release it from lamp assembly.
5. Withdraw bulb holder and remove bulb.

Installation



1. Install bulb in holder.
2. Install bulb and bulb holder in lamp assembly and rotate 1/4
turn to seat and retain.
3. Position direction indicator la mp at bumper aperture and
connect harness multiplug.
4. Engage inner end tang of lamp in bumper aperture.
5. Pivot lamp assembly and firmly seat outer retaining clip in
bumper aperture.

Exterior Lighting - Headlamp Assembly
Removal and Installation
Removal
1. Remove radiator grill. Refer to 76.55.03.
2. Remove radiator grill surro und. Refer to 76.55.15.
3. Remove headlamp trim panel. Refer to 76.11.23.

4. Disconnect headlamp levelling actuator if fitted.

5. Disconnect headlamp assembly harness connector.

6. Remove headlamp assembly to body lower nuts.
7. Remove headlamp to body upper nuts.

Installation

8. Remove headlamp assembly from vehicle.

1. Position headlamp assembly on body and install upper nuts.

2. Install headlamp to body lower nuts.

3. Connect headlamp assembly harness connector.
4. Connect headlamp levelling actuator harness connector if
fitted.

5. Align headlamp beams.
6. Install headlamp trim panel. Refer to 76.11.23.
7. Install radiator grill surround. Refer to 76.55.15.
8. Install radiator gril l. Refer to 76.55.03.

Exterior Lighting - Headlamp Leveling Motor
Removal and Installation
Removal
Installation



1. Disconnect harness multiplug from headlamp levelling
actuator.

2. Rotate actuator 1/4 turn inwards, tilt forward end downward
and withdraw assembly from headlamp.
1. With forward end tilted downward , position actuator assembly
on headlamp.
2. Align actuator with headlamp an d rotate it 1/4 turn outwards
to engage and fully seat.
3. Connect harness multiplug to actuator.
4. Carry out headlamp beam al ignment to the appropriate
alignment equipment instructions.

Exterior Lighting - High Beam Headlamp
Removal and Installation
Removal
Installation
1. Remove headlamp assembly fo r access. Refer to 86.41.33.

2. Release bulb holder securing tangs and position holder for
access.

3. Rotate pilot bulb holder 1/4 turn and withdraw holder.
4. Invert headlamp assembly.

5. Release headlamp unit adju sting screws and pivot.
1. Install headlamp unit on adjusting screw and pivot seats.

2. Invert headlamp assembly.

3. Install pilot bulb holder in headla mp unit and rotate 1/4 turn to
secure.

4. Install headlamp assembly bulb holder.
5. Install headlamp assembly. Refer to 86.41.33.
6. Align headlamp beams.

Exterior Lighting - High Beam Headlamp Bulb
Removal and Installation
Removal
Installation

1.
Open hood and install fender cover.

2. Release headlamp bulb holder locking tangs and remove holder from headlamp.
3. CAUTION: If the bulb is to be re-fitted, the glass must
not be touched with the bare hand . Failure to observe this caution
will result in premature bulb failure
Position bulb holder for access and remove bulb.
1. CAUTION: Headlamp bulbs are of the halogen type and
must not be handled with bare hands. Failure to observe this
caution will result in premature bulb failure.
Install headlamp bulb in holder.
2. Install bulb holder in headlamp ensuring that securing tangs
are fully seated.
3. Remove fender cover and close hood.

Exterior Lighting - High Mounted Stoplamp
Removal and Installation
Removal
Installation

1. Remove lamp cover.
1. Depress two tangs at base of lamp carrier and withdraw cover.

2. Disconnect lamp harness connector.

3. Remove module.
1. Release spring clips at each end of lamp lens module and withdraw module from carrier.

4. Remove lamp carrier.
Release lamp carrier lower securing tangs.
Slide carrier upwards to release and remove carrier from
backlight.
1. Ensure that rubber insulating pads are installed on lamp
carrier.