JEEP CJ 1953 User Guide

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

13330

FIG.
B-4—ENGINE
LUBRICATION
SYSTEM
—
DAUNTLESS
V-6
ENGINE

1—
Rocker
Arm Shaft
2—
Main
Oil
Line

3—
Oil
Inlet where it is connected by a drilled passage in the

cylinder
crankcase to an oil screen housing and
pipe assembly. The screen is submerged in the oil supply and has ample area for all operating condi­
tions. If the screen should
become
clogged
for any reason, oil may be drawn into the system over the
top
edge
of the screen, which is held clear of the

sheet
metal screen housing.

Oil
is drawn into the pump through the screen and
pipe assembly and a drilled passage in the
crank­

case, which connects to drilled passages in the
timing chain cover. All oil is discharged from the
pump to the oil pump cover assembly. The cover
assembly consists of an oil pressure relief valve,
an
oil filter bypass valve and a nipple for installa­
tion of an oil filter. The spring loaded oil pressure

relief
valve limits the oil pressure to a maximum
of 30 pounds [13.607 kg.] per square inch. The

oil
filter bypass valve
opens
when the filter has
become
clogged
to the
extent
that
4V2
to 5 pounds [2.04 a 2.27 kg.] pressure difference exists
between

the filter inlet and exhaust to bypass the oil filter
and
channel unfiltered oil directly to the main oil galleries of the engine.

A
full flow oil filter is externally mounted to the

oil
filter cover nipple on the right side of the en­ gine, just below the alternator. Normally, all
engine

oil
passes through the filter element; however, if
the element
becomes
restricted, a spring loaded bypass valve
opens
as mentioned above. The main

oil
galleries run the full length of the crankcase
and
cut into the valve lifter guide
holes
to supply

oil
at full pressure to the lifters. Connecting pas­
sages
drilled in the crankcase permit delivery of

oil
at full pressure to all crankshaft and camshaft
bearings.
Holes drilled in the crankshaft
carry
oil from the
crankshaft
bearings to the connecting rod bearings.
Pistons and cylinder walls are lubricated by oil
forced through a small notch in the bearing parting
surface on the connecting rod, which registers with
the
hole
in the crankpin
once
in every revolution. Piston pins are lubricated by splash.

Drilled
holes
in the camshaft connect the front camshaft bearing
journal
to the key slot in the front
of the camshaft. Oil flows from the
journal
into
the keyslot over the woodruff key in the space

between
the key and the camshaft sprocket and fuel pump eccentric.

The
forward end of the fuel pump eccentric in­ corporates a relief which allows the oil to escape

between
the fuel pump eccentric and the camshaft

distributor
gear. The oil stream strikes the distri­
butor shaft gear
once
each camshaft revolution, and provides ample lubrication of the timing chain and
sprockets by splash.

The
rocker arms and valves on each cylinder head

are
supplied with oil from the oil galleries through

holes
drilled in the front of the cylinder block and

cylinder
head. The
hole
drilled in the cylinder
head ends beneath the front rocker
arm
shaft brack­ et. A notch cast in the base of the rocker arm shaft

bracket
allows the oil to flow up inside the bracket

in
the space
between
the bracket and bolt, to the
hollow rocker arm shaft which is plugged at both
ends.
Each
rocker arm receives oil through a
hole

in
the underside of the shaft. Grooves in the rocker

arm
provide lubrication of the bearing surface. Oil
is metered to the push rod seat and valve stem
through
holes
drilled in the rocker arm. Excess
oil
drains off and returns to the oil pan through
passages in the cylinder head and block. Refer to
the
Lubrication
Chart
for lubrication frequency and

lubrication
type and grade.

B-7.
Chassis
Lubrication

Chassis
and
engine
should be serviced at periodic
intervals.
Most chassis lubricating points, whether
long-life or conventional, have standard lubrication
fittings. Refer to the
Lubrication
Specifications and

Service
Maintenance Schedule for specific points

and
lubricating time intervals. It is not necessary
to disassemble prepacked joints to lubricate them.

Merely
add new lubricant, as described in Par.
B-3,
to remove all old lubricant.

At
the appropriate interval, clean each lubrication
fitting indicated on the Lubrication
Chart
and
Service
Maintenance Schedule. Use a pressure gun
to lubricate. Be sure the grease channels are open
to provide complete lubrication of bearing surfaces.
In
some
cases it may be necessary to disassemble
to clear plugged channels.

When
vehicles are driven primarily in abnormally dusty or wet areas or when a vehicle is subject to
severe operating conditions, perform
these
services
more frequently. Under
these
conditions, no definite interval can be recommended because of the great variety of
uses
and conditions of use. 11

B
LUBRICATION B-3.
SERVICE
MAINTENANCE
SCHEDULE

Perform
the following operations at the mileage shown. Two thousand miles equals
3,200
km.

SERVICE
MAINTENANCE
SCHEDULE

OPERATION
VEHICLE
^ n>
MILEAGE
IN
THOUSANDS

6 8 10 12 24 30
Check Wheel Nut Torque*
Check
Fluid
Level
in Battery X Check
Fluid
Level
in Brake Master Cylinder0. X
Service
Cooling
System X Service Tires X

Lubricate
Distributor
Cam Lubricator (F4-134) X
Lubricate
Steering Linkage X

Lubricate
Propeller Shaft Universal Joints X

Lubricate
Propeller Shaft
Slip
Joints ; X
Lubricate
Tie Rod and Drag
Link
Sockets................................... X Change Engine
Oil
and
Filter,
and Service Air Cleaner (F4 134 Engine)** X
Change Engine Oil and
Filter,
and Service Air Cleaner (V6-225 Engine)**....
Check Brake Operation and Pedal
Free
Play X Check
Clutch
Pedal
Free
Play. .... X
Check all
V-Belt
Tensions X
Check Exhaust Emission System
(If
so equipped)*** \ X
Service Positive
Crankcase
Vent
Valve
and Breather . .' X
Road Test
Including
a Check of all Instrument
Lights
and Controls X Tune-up Engine
Check Operation of
Manifold
Heat
Control
Valve

Clean
Exterior of Radiator

Align
Headlights • Check Brake
Linings
,
Check Exhaust System for Leaks Replace Canister Air
Filter
(F. E. E. C. System)
Check
Axle
U-Bolt
Torque. Check Lubricaunt
Level
of Front
Axle
Universal Joints
Check Shock Absorber Mountings and Bushings Check Front and
Rear
Spring Bushings

Lubricate
Distributor
(V6-225).
Replace Spark, Plugs
Check Charging and Starting Circuits
Lubricate
Tailgate Latch, Supports and Hinges.

Lubricate
Door and
Hood
Hinge Pivots ;
Lubricate
Glove Compartment Door Latch

Lubricate
Heater Controls •

Lubricate
Windshield
Wiper and Washer Controls
Clean,
Repack and
Adjust
Wheel Bearings
Change Transmission and Transfer Lubricant. .
Replace
Dry-Type
Air Cleaner • Check Lubricant
Level
of
Differential

Lubricate
Transfer
Case
Shift
LeArer
Control
C«se.
. , . . . . . . . .
Continuing
each
2,000 miles

Continuing
each
6,000 miles

Continuing
each
24,000 miles

X
Continuing
each
30,000 miles
•Check after the
first
200 miles [320
km.
J
of operation.
If
wheel or wheels are changed for any
reason,
have
wheel nut torque rechecked after an additional two hundred miles of operation
••Service mileage shown or every 60 days, whichever occurs
first.

•••Maintenance check on emission system must be performed per
information
in this manual. "See text for brakes.

"Nj
^Miles
2,000
6,000
12,000
18,000
24,000
30,000
Kilometers

3,200
9,600
19,200
28,800
38,400 48,000

B-9.
Engine Oil

For
maximum
engine
protection under all driving conditions encountered during the recommended

oil
change intervals, it is necessary to use only

"MS"
certified
sequence-tested
oils. The term
"MS"
must appear on the oil container singly or

in
conjunction with other designations. "MS" des­
ignated oils are heavy-duty detergent oils that are
formulated to withstand all service conditions in
modern powerplants. Engine oils designated only
as
"ML"
and/or
"MM"
are not recommended and should not be used except in an emergency when

"MS"
oil is not available. Certified
sequence-tested

engine
oils are described on their containers by

such
phrases as:
meets,
exceeds,
excels, or has
proven superior in the
test
requirements,
test
sequences, MS Service
tests,
standards, and service

requirements,
of automotive manufacturers, auto­
makers,
or car manufacturers for MS service or
Service
MS.
It
may be necessary to change
engine
oil more
frequently than normally recommended, depending upon the type and quality of oil used, the severity
of operation conditions, if the
engine
is used for
short
periods in cold weather, or if the
engine
is allowed to idle for excessive periods.

Always
drain
the crankcase while the
engine
is hot since
dirt
and contaminants are then more
likely
to be held in suspension and therefore
will

drain
out more completely.
Drain
the crankcase as follows:

a.
Position the
drain
receptacle under the
drain

plug.

b.
Remove the
drain
plug using the correct size

wrench.
Be careful of hot oil.
c.
Carefully
clean the
drain
plug. Inspect and

replace
the gasket, if deteriorated.
d.
When the oil has drained, replace and tighten
the crankcase
drain
plug. 12

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

B
e.
Check
for the presence of
excess
water in the

oil
that might indicate an internal leak from the
cooling system.

f.
Pour oil into the oil filler tube. Replace the oil

filler
cap.

B-10.
Engine Oil
Filter
Service —
Hurricane
F4 Engine

The
engine
oil filter assembly should be replaced at each
2000
miles
[3.200
km.] of normal
engine

use. To remove the filter, use oil filter wrench
C-4065.
To install a new filter, wipe the gasket —
contact surface with
engine
oil, screw on the unit

until
gasket contacts the sealing surface, and then tighten at least one
half
turn
more. DO NOT USE

TOOLS.
Turn
by hand only. When refilling the
engine
crankcase after filter has been changed be

sure
to add one extra quart [1 ltr.] of oil to
fill

filter
and oil passages. Run
engine
to make sure there is no leak at oil filter.

B-l 1.
Engine Oil
Filter
Service — Dauntless V-6 Engine

To
replace the oil filter, use oil filter wrench, Tool

C-4065,
to remove the filter. After the filter has
been removed from the oil pump housing located
on the right front side of the engine, wipe the
housing surface clean and oil the gasket on the base of the new filter to make a
good
seal. Screw
the new filter in position until its gasket contacts
the pump housing surface, then tighten at least
one-half
turn
until filter fits snug.

Note:
Tighten by hand only, do not use a tool to
tighten.

Replace
oil filter each
6000
miles
[9.600
km.] at

engine
oil change.

B-12.
Exhaust
Manifold
Heat
Control
Valve
— Dauntless V-6 Engine

A
thermally-actuated heat control valve is located at
rear
of the right exhaust manifold of the Daunt­

less
V-6 engine.
This
valve has a bimetal thermo­
static spring which holds the valve closed when
the
engine
is cold.

Each
time the vehicle is lubricated place a few drops of penetrating oil on the valve shaft bushings

and
then work the valve by hand making sure that
the lubricant is worked into the bushings.

Note:
If the valve shaft
does
not operate freely
penetrating oil should be used to free the shaft.

B-l 3.
Positive
Crankcase
Ventilation
System

Service
the ventilation system of the
engine
each
multiple of
6000
miles
[9.600
km.] on the odometer
after
initial
2000
miles
[3.200
km.] service. Re­
place the ventilation valve each
12,000
miles
[19.200
km.].

For
information on servicing the positive crankcase
ventilation system on the
Hurricane
F4
engine
and
the Dauntless V-6 engine, refer to the Tune-up Section.

B-l4.
Distributor
— Hurricane F4 Engine

The
distributor shaft is lubricated through an oiler mounted on the side of the housing. Place three or four drops of light
engine
oil in the oiler each
2,000

miles
[3.200
km.]. Also place one drop of light
engine
oil on the wick located on the top of the
shaft, which is made accessible by removing the
rotor
arm. Sparingly apply cam lubricant to the
breaker
arm cam and place a drop of oil on the

breaker
arm pivot.

B-l
5.
Distributor
— Dauntless V-6 Engine

The
distributor has a lubricant reservoir that
car­

ries
sufficient
lubricant
for the life of the distributor.
When
servicing breaker points, place one drop of
light
engine
oil on the wick located on the top of the shaft Also, apply cam lubricant sparingly to
the breaker arm cam, and place a drop of oil on the

breaker
arm pivot.

B-l6.
Generator

On
early production vehicles oilers are provided
at each end of the generator, for lubrication
pur­

pose.
On late production vehicles one oiler is pro­
vided at the
rear
(bushing end) of the generator for lubrication purpose. Place two to four drops of
light
engine
oil in each oiler every
2,000
miles
[3.200
km.].

B-l
7. Spark Plugs

Replace
spark
plugs. Refer to Section C.

B-18.
Starting
Circuit

Check
the starting
circuit.
Refer to Section H.

B-l
9. Charging
Circuit

Check
the charging
circuit.
Refer to Section H.

B-20.
Engine Tune-Up

Refer
to Section C of this manual.

B-21.
Adjust
Fan
Belt

Refer
to Section C.

B-22.
Exhaust Emission
Control
System or
Controlled
Combustion System

•
Refer to the appropriate section in this manual.

B-23.
Exhaust System

Check
the exhaust system for leaks. Refer to Section F.

B-24.
Fuel Evaporative Emission
Control
Canister Air
Filter

The
only service required for the
F.E.E.C.
system
is cleaning the air cleaner filter mounted at the
bottom
of the canister. The filter requires replace­
ment at
12,000
mile intervals. Refer to Section

E,
Par. E-9 for service procedure.

B-25.
Oil Bath Air Cleaner
Some 'Jeep' Universal vehicles are equipped with

an
oil bath type air cleaner.
This
type air cleaner
thoroughly removes all dust from the air before it enters the carburetor, if it is properly serviced.

When
the vehicle is operated under normal condi­
tions the air cleaner must be serviced at regular

intervals
as care of the air cleaner is extremely 13

LUBRICATION

vital
to the life of the
engine.
When the vehicle
is operated under abnormal conditions, (for ex­
ample when driven on secondary roads or through
fields) then service of the air cleaner must be more frequent

Note:
Under extreme continually dusty and dirty
conditions where the vehicle operates in clouds of dust and
dirt,
service the air cleaner daily.

a.
To service the air cleaner on vehicles equipped
with the
Hurricane
F4
engine
(Fig. B-5) unscrew
the eye
bolt
on the oil cup clamp and remove the

oil
cup from the cleaner body. Remove the oil from the cup and scrape all
dirt
from the inside, wash cup clean using a cleaning solution if neces­

sary.
In summer
refill
the oil cup with IV2 pints [0,6 ltrs.] of
SAE-40
or 50 grade
engine
oil. In
winter
refill
using grade
SAE-20
engine
oil. For
servicing the air cleaner
body
(less
oil cup),
loosen

hose
clamp and remove
hose
from the cleaner. Detach breather
hose
from the fitting on the cleaner. Remove the two wing screws and lift the
cleaner from the vehicle. Agitate the cleaner
body

thoroughly in cleaning solution to clean the filtering

element.
Dry
element
with low pressure com­ pressed air. Reinstall the cleaner
body
and replace
the oil cup. Service the air cleaner every
2000
miles
[3.200
km.].
b. To service the oil bath air cleaner on vehicle
equipped with the Dauntless V-6
engine
(Fig. B-6),

first
remove the air cleaner from the carburetor
by unscrewing the wing nut. Remove the oil cup
FIG.
B-5—OIL
BATH AIR
CLEANER
-
HURRICANE F4 ENGINE 1—
Horn
7—Clamp
2—
Flexible
Connector
8—Oil
Cup
3—
Hon
Clamp
9—Clamp

A—Carburetor
Vent Tube 10—Hose 5— Body 11—Clamp
6—
Screw
and
Lock
Washer 13—Gasket
FIG.

B-6—OIL BATH AIR
CLEANER
-
DAUNTLESS V-6 ENGINE

1—WinB
Nut
2—
Cover

3—
Rubber
Gasket
4—
Cork
Gasket
5—
Oil
Cup 6—
Breather

7—
Clamp

8—
Vent
Tube 9—
Air
Pump Hose from cleaner
body
and remove the oil from the cup,
scrape all
dirt
from the inside.
Clean
oil cup thor­
oughly, wash filter
element
in a solvent that
will
leave it clean and dry.
Fill
oil cup to indicated
level with clean
S.A.E.
40 or 50 grade
engine
oil
(S.A.E.
20 grade in winter.) Assemble cleaner filter

element
to oil cup making sure that gasket is in
place
between
the two pieces. Assemble air cleaner assembly to carburetor making sure the gasket
be­

tween
air cleaner and carburetor is in place. Secure

air
cleaner to carburetor with wing nut. Service the

air
cleaner every
6000
miles
[9.600
km.],
c.
Carefully
check the
hose
clamps and
fittings
on
the breather
hoses
at frequent intervals. Loose con­nections
will
affect proper operation of the
crank­

case ventilating system.

B-26. Dry-Type
Air Cleaner Service the air cleaner on Dauntless V-6
engines

at each oil change under normal driving conditions.

If
the vehicle is operated under dusty conditions,
check the condition of the air cleaner
element
more
frequently and service if dirty.

Servicing
the air cleaner consists of cleaning or replacing the air cleaner
element
and replacing the

crankcase
ventilation filter (breather assembly). See Fig. B-7.

The
air cleaner
element
assembly consists of a
paper
element
and a polyurethane
element
The
paper
element
cannot be cleaned.

To
clean the polyurethane
element,
first carefullly remove it from the paper
element
Then
wash it in 14

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

B
solvent.
Wrap
the polyurethane element in a clean

dry
cloth and
squeeze
to remove all possible sol­
vent. Do not wring the element or it may
become
torn.
After cleaning, oil the polyurethane element

liberally
with
engine
oil
(SAE
10W30) and
squeeze

to evenly distribute the oil through the element and to remove
excess
oil. The element should be damp

with
oil, not dripping.
Install
the polyurethane element on the paper element, taking care to have
edges
of the polyurethane element over the plastic end plates of the paper element.

Replace
the complete air cleaner element assembly every
24,000
miles
[38.400
km.]. Replace more
frequently if there is any apparent damage or evidence of plugging.

The
crankcase ventilation filter should be replaced, not cleaned, every
6,000
miles
[9.600
km.]. The
filter
is located inside the air cleaner housing.
12992

FIG.
B-7—DRY-TYPE
AIR
CLEANER DAUNTLESS
V-6
ENGINE

1—
Crankcase
Ventilation
Filter

2—
Polyurethane
Element

3—
Paper
Element
B-27.
Steering
Gear

Check
that the steering gear lubricant is at the
level of the fill-hole. If not, add lubricant to the
level of the fill-hole with the lubricant recom­ mended in the
Lubrication
Specifications. If abnor­

mally
low, check the steering gear for possibility
of leaks.

B-28.
Cooling System
Check
the coolant level in the
radiator.
It should be

half
an inch below the neck. If not,
fill
the radiator
to
half
inch below the neck with the proper coolant.

Refer
to Section G.

If
the level of the coolant is abnormally low, check
the radiator,
hoses
and water pump for possible
leaks.
If a leak is suspected, refer to Section G.

B-29.
Clean
Exterior
of Radiator

For
proper cooling efficiency the radiator should be cleaned of foreign objects. Refer to Section G.

B-30.
Transmission
and
Transfer Case
Lubricant
Level
Cheek

•
Refer to Par. B-31 through B-33 as applicable.
B-31.
General

All
transfer cases and transmissions should be

serviced
separately even though drilled passages
are
provided for oil circulation
between
some
trans­
mission and the transfer case housings. Procedure

from
the appropriate Par. below should be fol­ lowed to check the lubricant level of the various

types
of transfer cases and transmissions.
If
the transfer case or transmission fluid levels
are
found to be abnormally low, check both units
for any possible leaks.

B-32.
Transfer
Case
:

The
transfer case fill-hole is located on the right side of the transfer case housing. To check the
lubricant
level, remove the
fill
plug.
Lubricant

should be level with this fill-hole. If not, bring up to level by adding make-up lubricant as specified

in
the
Lubrication
Specifications.

B-33.
Transmission

The
transmission fill-hole is located on the right side of the transmission housing. To check the
lubricant
level, remove the
fill
plug.
Lubricant

should be level with this fill-hole. If not, bring
up to level by adding make-up
lubricant
as specified
in
the
Lubrication
Specifications.

B-34.
Transmission and Transfer
Case
Lubricant
Change

•
Refer to Par. B-35 through B-37 as applicable.

B-35.
General

Transfer
case and transmission lubricants should
be changed at the same time.

B-36.
Transfer
Case

To
drain
the transfer case, first remove the transfer
case fill-hole plug and then the transfer case
drain-

hole
plug. Let all fluid
drain
from case.
Then
install
the transfer case drainhole plug, and
refill
the
transfer
case through the fill-hole using the correct

lubricant
as specified in the
Lubrication
Specifica­
tions.

At
30,000
mile
[48,000
km.] intervals lube the

transfer
case shift levers with
Lubriplate
No.
130AA.
Late
models have a lube fitting. To lube
older models, (without lube fitting) remove the

bottom
cover of the case, clean thoroughly and
pack
case
full
of lubricant.

B-37.
Transmission (3-Speed)

To
change the lubricant on all vehicles equipped

with
a three speed synchromesh transmission,
drain

the old fluid by first removing the fill-hole plug

and
then removing the drainhole plug. Since on

some
transmissions there are drilled passages be­ tween the transmission and transfer case that allow

oil
to circulate
between
the two units, the transfer
case should be drained before refilling the trans­

mission.

When
all the fluid is completely drained, replace
the drainhole plugs only. For the correct specifi­
cations and quantity, refer to the
Lubrication
Specifications. 15

B

LUBRICATION
Note:
Hard
shifting of the transmission gear in
cold weather is a positive indication that the
lubri­

cant
is of the wrong viscosity or of poor quality

which
allows it to congeal.

B-38.
Optional
4-Speed
Transmission
and
Transfer Case

The
four-speed transmission and transfer case re­

quire
separate lubrication for each unit as
they
have no cross-over oil passage. At each transmission
service check, the
fill
plugs of
both
four-speed

transmission
and transfer case should be pulled
and
the lubricant refilled to level if necessary.

B-39.
Transfer
Case
Linkage

The
transfer case shift linkage should be lubricated

periodically.
All
bearing surfaces that are assembled
with
studs and cotter pins should be disassembled, cleaned, and coated with a
good
waterproof grease.

The
bearing surfaces that cannot be disassembled
should be lubricated with a lubricant that
will
penetrate the bearing
area.
These bearings include
the two on the cross shaft assembly and the
threaded stud.

The
type
of penetrating lubricant recommended is
DuPont
"PM 7", No. 2911, or its equivalent.

B-40.
Brake Master Cylinder

Clean
the top of the
fill
cap and also the housing

area
around it. Remove the cap and observe the
fluid
level. It should be
half
an inch
below
the top
of the fill-hole. If not, add brake fluid to
half
inch
[1,3 cm.]
below
the top of the fill-hole. Use
only heavy-duty brake fluid conforming to speci­
fication
SAE-J-1703.
Be sure to handle the brake

fluid
in clean dispensers and containers that
will
not introduce even the
slightest
amount of other

liquids
or foreign particles. Replace and tighten
the
fill
cap.

B-41.
Adjust Brakes

Refer
to Section P.
B-42.
Brake Linings

Refer
to Section P.

B-43.
Adjust Clutch

Refer
to Section I.

B-44.
Clutch Cross Shaft (Lever Type)

Lubricate
the clutch cross shaft in accordance with
specifications given in the
Lubrication
chart: see
Item
1. Chassis Bearings.

B-45.
Tie Rod and Drag
Link
Sockets

The
tie rod and drag
link
sockets
are equipped

with
lubrication
fittings
and should be lubricated

per
specifications given in the
Lubrication
chart: see Item 1. Chassis Bearings.
B-46.
Front
and
Rear Spring
Bushings

The
condition of the spring bushings is indicated
by the alignment of the spring pivot and spring
shackle
bolts.
Check
the alignment of
these
bolts,

and
check that nuts are
tightened
securely.

B-47.
Spring
Shackles

Rubber
bushings are provided on the spring
shackles.
These rubber bushings have no lubrication
fitting and it is very important that
they
never be lubricated.

B-48.
Shock Absorbers

Visually
check for broken mounts or bolts, worn

or
missing bushings on the shock absorbers. Refer
to Section S.

B-49.
Front and
Rear
Axle
U-Bolts

Torque
the front and
rear
axle U-bolts. Refer to Section S.

B-50. Front
and
Rear
Axle
Differentials
—
Lubricant Levels

The
lubricant
level of all front and
rear
differentials should be at the level of the fill-hole.

B-51.
Front and
Rear
Axle
Differentials
—
Changing
Lubricant
B-52.
Conventional Differentials

To
remove the lubricant from the front or
rear
differential,
it is necessary to remove the housing cover. Let the lubricant
drain
out, and then flush
the differential with a flushing oil or light
engine

oil
to clean out the housing
(except
Powr-Lok
or
Trac-Lok
Differentials). Do not use water, steam,
kerosene, or
gasoline
for flushing.

Reinstall
the housing cover, replacing the gasket whenever necessary, torquing the cover
bolts
to 15 to 25 lb-ft. [2,1 a 3,4 kg-m.].
Remove the filler plug, and
refill
the differential
housing as specified in the
Lubrication
Specifica­
tions.

B-53.
Powr-Lok
or
Trac-Lok Differential

Some vehicles may be equipped with the
Powr-Lok

or
Trac-Lok
Differential as optional equipment.
Special
lubricant and ordinary multipurpose gear

lubricants
must
not be used. Use only
'Jeep*
Differ­

ential
Oil,
Part
No. 94557.

Powr-Lok
or
Trac-Lok
differentials may be cleaned
only by disassembling the unit and wiping with
clean
rags. Do not flush the unit. Refer to Sec­
tion N.

B-54.
Front Axle Universal Joint
—
Lube

Check
the level of the front axle universal joint
lubricant
at each front wheel by removing the
fill-hole plug. The lubricant should be level with
the fill-hole. If required, add lubricant as specified

in
Lubrication
Specifications.

B-55.
Front
Axle
Universal
Joint
— Service

On
all 4-wheel drive vehicles the front axle
uni­

versal
joint should be serviced by removing the shaft and thoroughly cleaning the universal joints

and
housing. For the correct procedures, refer to
Section M. 16

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

B
Reinstall
the axle shafts, and
refill
the housings to
plug level using the universal joint lubricant
specified in
Lubrication
Specifications.

B-56.
Front
Axle Wheel Bearings

To
lubricate the wheel bearings, it is necessary
to remove, clean, repack, and adjust them. When
front wheel hubs and bearings are removed for
lubrication,
they should be thoroughly washed in a
suitable cleaning solvent. The bearings should be
carefully
dried and then given a thorough cleaning

and
inspection. Use a clean brush to remove all

particles
of old lubricant from bearings and hubs.

After
the bearings are cleaned, inspect them for
pitted races and rollers. Also, check the hub oil
seals.

Note:
Wheel bearing lithium base lubricants are
used at the factory for
initial
fill
of
these
bearings.
When
lithium base and sodium base lubricants are

mixed,
the result is a thinned-out mixture that
can
bleed through seals. It is therefore important
that lubricants with the correct base be used when

lubricating
the wheel bearings.
Should
leaks occur at wheel bearing seals, the leaks

may
be caused by a mixture of two
types
of
lubri­

cants.
In such cases, the old lubricant should be
completely removed before new lubricant is added.

Wheel
bearings should be thoroughly cleaned,
lubricated
with lithium base and reinstalled.

Repack
the bearing
cones
and rollers with grease

and
reassemble hub in the reverse order of the
disassembly. Test the bearing adjustment as out­

lined
in Section Q.

B-57.
Rear
Axle Wheel Bearings

The
Rear
wheel bearings an early models equipped

with
lubrication fittings with a vent opening
through the housings above each fitting should be
lubricated
sparingly, each
2,000
miles
[3.200
km.].

Use
a hand compressor and wheel bearing grease,
forcing
the grease through each lubrication fitting

until
it flows from the vent. Vent should be kept
clear
of obstruction or grease
will
back up into the

brakes.
Do not add grease after it flows from the
vent for it may be forced through the wheel key-
way
onto
the outside of the wheel and possibly

onto
the brake linings.
Rear
wheel bearings that do
not have lubrication fittings should be removed
each
12,000
miles
[19.200
km.] and the bearing
cleaned, inspected and repacked. Refer to proce­

dure
in Par. B-56.

Note:
When servicing the Flanged Axle Unit
Bear­

ing Assembly, refer to Section N, Par. N-5 for

proper
lubrication procedures.

B-58.
Propeller Shafts
and
Universal Joints

The
propeller shaft slip joints and universals should
be lubricated with a hand compressor grease gun so as to not damage the bearing seals. The units
should be lubricated with a
good
quality grease.

Refer
to the
Lubrication
Chart
for lubrication fre­
quency and lubricant type and grade. B-59.
Lights
and
Controls

a.
Check
all interior and exterior lights and light
switches for proper operation, including: parking
lights, headlamps (high beam and low beam),

tail
lights, brake lights, directional lights, and in­ strument panel lights.

b.
Check
all instrument panel controls and
instru­

ments for proper operation.

B-60.
Speedometer Cable

Remove the
speedometer
cable from its housing every
12,000
miles
[19.300
km.].
Clean
it thor­
oughly and coat it with a
good
quality light graphite grease.

B-61.
Headlights

Refer
to Section H.

B-62.
Heater Controls

Apply
Lubriplate
130-A to all friction points and
pivot points on the heater controls panel unit as well as the pivot points at the dashpot. Apply

a
few drops of penetrating oil all along the Bowden
cable.
This
oil
will
penetrate into the center wire.

B-63.
Windshield Wiper and
Washer Controls

Lubricate
the friction points and the pivot points
on the windshield wiper transmission and linkage

arms
with a slight amount of
Lubriplate
130-A.

B-64.
Rotate Tires

Refer
to Section Q for the correct method of rotat­ ing the tires.

B-65.
Body Lube Points
•
Refer to Par. B-66 through B-68.

B-66.
Hood Hinge Pivot Points

Lubricate
the frictional points of the hood hinge
pivot points with a few drops of light-weight
engine

oil.
B-67.
Glove Compartment Door Latch
Sparingly
wipe
Lubriplate
130-A on the
glove
com­
partment door latch.

B-68.
Tailgate Hinges

Lubricate
the friction points of the tailgate hinges

with
a few drops of light-weight
engine
oil.

B-69.
LUBRICATION
OF
OPTIONAL EQUIPMENT

B-70.
Pintle Hook

When
lubricating the vehicle, place a few drops of oil on the pintle hook and safety latch pivot pins.

B-7!.
Centrifugal Governor

Check
the oil level in the governor housing at each
vehicle lubrication. Use the same seasonal grade
oil
as is used in the
engine
and change oil at each

engine
oil change. Do not
fill
the housing above
the level indicating plug opening. Keep the vent

in
the filler plug open at all times. 17

B

LUBRICATION
B-72.
Powr-Lok
or Trac-Lok
Differential

Refer
to Par. B-53.

B-73.
PARTS
REQUIRING
NO
LUBRICATION

B-74.
Water Pump Bearing,
Clutch
Release
Bearing

The
water pump and clutch release bearings are

prelubricated
for life when manufactured and cannot be relubricated.

B-7S.
Starter
Motor
Bearings

The
starting motor bearings are lubricated at assembly to last
between
normal rebuild periods.

B-76.
Alternator Bearings

The
alternator bearings are lubricated at assembly

and
require no further lubrication.

B-77.
Springs

The
vehicle springs should not be lubricated. At assembly the leaves are coated with a long-lasting

special
lubricant which is designed to last the life
of the springs. Spraying with the usual mixture of
oil
and kerosene has a tendency to wash this
lubri­

cant
from
between
the leaves, making it necessary
to relubricate
often
to eliminate squeaking.

B-78.
Shock Absorbers

Hydraulic
direct-action shock absorbers are per­ manently sealed and require no periodic
lubrica­

tion service. Shock absorber mounting bushings
are
not to be lubricated.

B-79.
LUBRICATION
REQUIREMENTS
FOR
OFF-HIGHWAY
OPERATION

Adequate lubrication
becomes
increasingly im­ portant when vehicles are used in off-highway
operation. Under
these
conditions all operating
parts
of both the
engine
and chassis are subjected
to unusual pressures. At the same time such operation is usually under abnormal dust and
dirt

conditions making additional precautions neces­

sary.
The importance of correct lubrication for
the conditions of operation cannot be overestimated.

B-80.
Engine
Oil

It
is important, that the oil in a new or rebuilt
engine
be changed after the first
eight
or ten hours
of operation, and for heavy, dusty work, every 50

hours
thereafter. Watch the condition of the oil closely and change it immediately if it appears to
be contaminated.

i-Il.
Engine
Oil
Filter

Replace
the oil filter at the end of the first 100

hours
of service. Under extreme operating con­ ditions, more frequent replacement may be re­
quired.
The condition of the oil is a reliable

indicator
of the condition of the filter element.
If
the oil
becomes
discolored and shows evidence
of contamination, change the filter without delay.
(Refer
to
Par.
B-10, B-ll for the correct procedure
for replacing the oil filter.)

B-82.
Air Cleaner

Care
of the air cleaner is extremely vital to the life of the engine. Pay particular attention to the
amount of dust and
dirt
in the air taken into the

engine
through the air cleaner. When dust is not
noticeable in the air, service the air cleaner each scheduled maintenance period. Whenever the air is
noticeably dusty (for example when the vehicle is

driven
on secondary roads or through fields) then
service the air cleaner more frequently. Under extreme continually dusty and dirty conditions
where the vehicle operates in clouds of dust and

dirt,
service the air cleaner daily. (Refer to Par.
B-24
thru
B-26 for service procedures.)

B-83.
Chassis
Lubrication

The
period of lubrication depends entirely upon the type of work being done. Using the specified

interval
given in the Service Maintenance Schedule as a guide, lubricate at safe intervals required for
the particular type of operation. Under extremely
dusty conditions lubricate
these
points daily. Be

sure
to force enough lubricant into each fitting to force out the old lubricant which might be con­
taminated with grit and which would cause
rapid

wear
if allowed to remain.
Do not place lubricant on the various
ball
and socket joints or pivot points of the lift linkage as
dirt
will
accumulate to form an abrasive mix­

ture.
It is
best
to simply wipe
these
parts clean

with
a cloth.

B-84.
Front
Axle
Shaft Universal Joints

For
off-highway use remove the universal joints twice yearly, thoroughly clean both the housings

and
joints with a suitable solvent, and
refill
the
housings to the
fill
plug opening levels with the

correct
lubricant as given in the
Lubrication
Specifications.

B-85.
Transmission and Transfer
Case

The
combined capacity of the two housings is
small
for economy, making it important that the

lubricant
be changed at regular intervals. For off-highway use
drain
both housings every 300

hours
of operation and
refill
to the
fill
plug opening
levels. Refer to B-35 through B-37 when changing

lubricant.

B-86.
Front and
Rear
Axle
Differentials

Because of the higher pressure developed in the
axle assemblies with heavy duty operation,
drain,

flush,
and
refill
the differential assemblies each 300 hours of operation. Use only flushing oil or light
engine
oil to clean out the housings (except

Powr-Lok
and
Trac-Lok
differentials). Refer to
Par.
B-52 and B-53 for draining and flushing

differential.
18

Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

c
TUNE-UP

Contents

SUBJECT
PAR.

GENERAL
C-l

TUNE-UP
.C-2
Air
Cleaner
C-21

Battery
. C-3
Carburetor
Adjustments
C-2 5

Coil
C-20
Crankcase
Ventilation C-6

Cylinder
Compression C-9

Cylinder
Head(s) .C-5

Dash
Pot Adjustments .C-26

Distributor
Service C-10
thru
C-13

Distributor
Resistance Test C-l6

Fan
Belt
C-2 7
Fuel
Lines
and Screens
C-2
2

C-l.
GENERAL
An
engine tune-up should be performed for all
Jeep Vehicles each 6000 miles [9.600 km.] or at the end of each 250 hours off-the-road operation,
to ensure best possible performance at all times.
The
tune-up should follow the sequence given in
this section.
Because of federal laws limiting exhaust emissions,

it
is even more important that the engine tune-up is
done
accurately, using the specifications listed
on the tune-up sticker found in each engine com­

partment.

Note;
To ensure proper operation and effectiveness
of the exhaust emission control system, and to
comply with
Federal
and State requirements, a
recheck
of ignition timing, idle speed and idle mix­

ture
and necessary adjustments must be performed
after the first
2,000
miles [3.200 km.] of vehicle
operation.

A
minor engine tune-up should be performed every
6,000
miles [9.600 km.] or at the end of 250 hours
of off-the-road use.
Major
engine tune-up should
be performed every 12,000 miles [19.300 km.].

The
parts of units which affect power and perform­
ance may be divided into three groups:
(1) Units affecting compression
(2) Units affecting ignition
(3) Units affecting carburetion

The
tune-up procedure should cover
these
groups
in
the order given. While the items affecting com­
pression and ignition may be handled according
to personal preference, correction of items in the
carburetion
group should not be attempted until

all
items affecting compression and ignition have
been satisfactorily corrected.

Note:
To make sure hydro-carbon and carbon
monoxide emissions
will
be within limits, it is very

impotrant
that the adjustments be followed exactly
as listed on the sticker found in each engine compartment.
SUBJECT
PAR.

Fuel
Pump . . C-23

Heat
Control
Valve C-7

Ignition
Cables C-19

Ignition
Timing
. C-14

Ignition
Wires C-l8

Manifold
C-5

Manifold
Vacuum C-24

Point
Dwell C-17

Primary
Circuit
Tests
.................
C-15
Spark
Plugs C-4

Tappets
C-8

ROAD TEST C-2
8

SERVICE
DIAGNOSIS
. : C-29

TUNE-UP SPECIFICATIONS..
C-30

Minor
engine tune-up consists of the following.
Inspect
and correct as required:
Battery
cables and connections.
Alternator
and regulator wiring.

Primary
— Secondary wiring, distributor cap.

Cylinder
head torque.

Contact
point dwell.

Vacuum
and centrifugal advance.

Ignition
timing.
Spark
plugs for correct air gap.

Adjust
idle speed and idle air mixture.

Adjust
all drive belt tensions.
Clean
carburetor air cleaner.

Lubricate
exhaust manifold damper.

Major
engine tune-up includes the following.
Inspect
and correct as required:
Battery
condition and charging
circuit.
Clean,
lubricate
and tighten battery cable connec­
tions.

Ingition
system.
Spark
plugs; replace if necessary or clean and gap.

Compression
check.

Primary—Secondary
wiring, distributor cap.

Replace
contact points and condenser.

Lubricate
distributor cam with cam grease.
Adjust
contact points.

Check
vacuum and centrifugal advance. Set ignition timing.

Torque
cylinder head.
Adjust
idle speed and idle air mixture.

Replace
fuel filter element (every 12,000 miles [19.300
km.]).

Adjust
all drive belt tensions.

IMPORTANT: SPECIFICATIONS
FOR EN-

GINE
RPM.
DISTRIBUTOR POINT DWELL,
AND IGNITION TIMING GIVEN
IN
TUNE- UP SECTION
C
REFER
TO
VEHICLES
WITH
AND WITHOUT EXHAUST EMISSION CON­

TROL
SYSTEMS.

FOR
VEHICLES
EQUIPPED WITH EXHAUST
EMISSION CONTROL SYSTEMS ALSO
REFER
TO
SECTION
Fl (F4-134
ENGINE)
AND
F2 (V6-225
ENGINE).
19

c

TUNE-UP
C-2.
TUNE-UP SEQUENCE

The
following
Pars.
C-3 through
C-2
7
give the
sequence and describe the services to be performed
when tuning the engine.

C-3.
Clean
and
Check
Battery
Inspect
battery and cables. If the battery is not
satisfactory, install a fully-charged battery to allow
completion of the tune-up.
Note: If the battery fails any of the following tests,
remember that the cause may be other electrical
trouble, and not necessarily only a defective battery.
Refer
to Section H for electrical troubleshooting

and
tests.

a.
Check
the specific gravity of the eletrolyte in
each cell of the battery. A hydrometer reading of 1.260 indicates that the battery is fully charged.

If
the reading is 1.225 or below, the battery
needs

recharging.
If one or more cells is 25 "points" (.025)

or
more lower than the other cells, this indicates
that the cell is shorted, the cell is about to
fail,
or
there is a
crack
in the battery partition in the case.
Unless the battery is repaired or replaced, battery trouble
will
soon be experienced.

b.
Check
the electrolyte level in each cell, add

distilled
water to maintain the solution %" [9.5
mm.] above the plates. Avoid overfilling. Replace
the filler caps and tighten securely. It is important
to keep the electrolyte level above the plates at
all
times because plates that are exposed for any
length of time
will
be seriously damaged.

c.
Check
the wing nuts on the hold-down frame
for tightness. Tighten them only with finger pres­

sure,
never with pliers or a wrench. Excessive pres­

sure
could damage the battery case.

d.
Clean
the battery terminals and cable connec-
FIG.
C-l—FRAME
GROUND
STRAP
—

HURRICANE
F4
1—
Right
Front
Engine Mount

2—
Frame
Ground
Strap
DAUNTLESS
V-6
tors.
Prepare a strong solution of baking soda and

water
and brush it around the terminals to remove

any
corrosion that is present. The cell caps must
be tight and their vents sealed to prevent cleaning
solution entering the cells. After cleaning install
cable connectors on terminals and coat the ter­
minals
and connectors with heavy grease.
e. Inspect the battery cables and replace if badly

corroded
or frayed.
Check
tightness of terminal
screws to ensure
good
electrical connections.
Check

the tightness of the negative ground cable connec­ tion at the engine to ensure a
good
ground con­ nection.

f.
Load
test
the battery. Connect a voltmeter across the battery. Run the starting motor for 15 seconds.
If
the voltage
does
not drop below 10 volts on a 12 volt battery the battery is satisfactory. If the
voltage falls below
these
values, yet the specific
gravity
is above
1.225,
the condition of the battery
is questionable.

g.
Make sure the engine to frame ground strap or
cable connections are tight. If
these
connections
are
loose,
corroded or dirty,
hard
starting or failure
of the vehicle electrical system may result. Refer
to
Fig.
C-l
for location of the
Hurricane
F4 engine
to frame ground strap and its connections. Refer to Fig. C-2 for location of the Dauntless V-6 en­ gine to frame ground cable.

C-4.
Clean and
Adjust
Spark Plugs
Clean,
inspect, and gap
spark
plugs. Do not install

spark
plugs until completion of compression tests.

a.
Use a
Spark
Cable
and Installing
Plier
Tool,

W-2
74,
to remove the leads from the
spark
plugs.

Caution:
Pulling on the cables to remove them

from
the
spark
plugs can cause internal breaks in
the leads that
will
cause ignition failure.

b.
Using a
spark
plug wrench, loosen each
spark

plug one or two turns to break
loose
any carbon
deposits on the plug base. 20