technical specifications Lancia Musa 2007 Owner handbook (in English)

267
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
For versions with alloy rims
❒Make sure that hub contact surfaces are clean;
❒Refit the standard wheel fitting it on the pins, refit the fastening
bolts and tighten them using the wrench provided;
❒Lower the car and remove the jack;
❒Using the wrench provided, tighten the bolts in the sequence
shown previously for the space-saver spare wheel (see figure);
❒Refit the snap-fitted wheel hub cap.
When you have finished
❒Stow the spare wheel C in the space provided in the boot;
❒Insert the jack partially open in its container B forcing it lightly to
prevent it from vibrating when travelling;
❒Put the tools back into their places in the container;
❒Stow the container complete with tools on the spare wheel and
secure everything with the clamping device A;
❒Correctly re-position the stiff cover.
L0D0161m

268
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that it has
not fused before changing the bulb. For the
location of the fuses, refer to “If a fuse blows” in
this chapter;❒Before replacing a bulb that does not work,
check that the contacts are not oxidised;
❒Burnt bulbs must be replaced by others of the
same type and power;
❒Always check the height of the headlight beam
after changing a bulb.
Only touch the metal part when handling halogen bulbs. If the transparent bulb is touched it
reduces the intesity of the light emitted and can also reduce the life of the bulb. If you touch the
bulb accidentally, rub it with a cloth moistened with alcohol and leave it to dry.
WARNING
Modifications or repairs to the electrical system carried out incorrectly and
without bearing the features of the system in mind can cause malfunctions with
the risk of fire.
WARNING
Halogen bulbs contain pressurised gas which, if broken, may cause small
fragments of glass to be projected outwards.

269
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IMPORTANT The headlight inner surface may be lightly misted over:
this is not a fault but a natural fact due to low temperature and the
level of air humidity. It will disappear as soon the headlights are
turned on. The presence of drops inside the headlights means water
infiltration, therefore contact Lancia Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your car:
AGlass bulbs: clipped into position. Pull to remove.
BBayonet type bulbs: press the bulb, turn counterclockwise to
remove this type of bulb from its holder.
CTubular bulbs: free them from their contacts to remove.
D-EHalogen bulbs: to remove the bulb, release the clip holding
the bulb in place.
L0D0178m

270
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
Bulb Ref. Figure Type Power
Main beam headlightsEH3 55W
Dipped beam headlights DH7LL 55W
Front side lights AW5WLL 5W
Front fog lights (where provided)EH1 55W
Front direction indicators (orange)BPY21W 21W
Side direction indicators AWY5W 5W
Rear direction indicators BPY21W 21W
Taillights BP21/5W 21W/5W
Brake lightsBP21/5W 21W/5W
Third brake light (additional brake lights) AW2,3W 2,3W
Reversing light BP21W 21W
Rear fog lights BP21W 21W
Number plate lights CC5W 5W
Front ceiling lightAW5W 10W
Rear ceiling lightAW5W 10W
Rear ceiling lights (with sunroof)AW5W 5W
Boot light AW5W 5W

271
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT BURNS OUT
For the type of bulb and power rating, see “When needing to change
a bulb”.
FRONT LIGHT UNITS
The front light units contain the side/taillights, dipped beam, main
beam and direction indicator bulbs.
To replace side/taillight, dipped beam and main beam bulbs:
disconnect the power connector, release retainer B and remove
cover A.
The bulbs are arranged inside the light unit as follows:
C: Direction indicators
D: Main beam headlights
E: Sidelights
F: Dipped beam headlights
Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
L0D0345m
L0D0346m

272
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒turn the bulb holder A counterclockwise and remove it;
❒release the two tabs B from the catches, remove bulb C and replace
it;
❒refit the bulb holder A into its seat and turn it clockwise.
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒release the bulb holder catch A;
❒disconnect the electric connector B;
❒remove the bulb C and replace it;
❒fit the new bulb, making the tabs of the metallic part coincide with
the grooves on the reflector, reconnect the electrical connector B
then hook the bulb holder catch A;
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
L0D0348m
L0D0350m

273
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒turn the bulb holder A counterclockwise and remove it;
❒remove the bulb B pushing it gently and turning counterclockwise
(“bayonet”);
❒replace the bulb;
❒refit the bulb holder turning it clockwise, checking that it is
secured correctly.
Side
To change the bulb, proceed as follows:
❒lever in the point shown by the arrow to compress the catch and to
remove unit A;
❒turn the bulb holder B counterclockwise, remove the snap-fitted
bulb and replace it;
❒refit the bulb holder B in the transparent cover, then position the
unit making sure the catch clicks into place.
L0D0351m
L0D0148m

274
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
FRONT SIDELIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒remove the snap-fitted bulb holder A, remove the bulb B and
replace it;
❒refit the snap-fitted bulb holder A;
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
FRONT FOG LIGHTS (where provided)
Contact Lancia Dealership to replace front fog light bulbs.
L0D0353m
L0D0354m

275
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
REAR LIGHT UNITS
To change the bulb, proceed as follows:
❒open the tailgate;
❒turn the fastener A counter-clockwise (for the left lid) or clockwise
(for the right lid) and remove the cover;
❒disconnect the electrical connector C;
❒slacken the two fastening nuts B;
❒to remove the headlight, pull it in perpendicular direction using
the handle on the headlight;
❒press the bulb holder tabs and remove it from its housing;
❒remove bulbs D - E - F - G lightly pushing them and turning them
counter-clockwise;
❒refit the bulb holder and make sure the two tabs are fastened and
then connect the electrical connector C; drive in the two fastening
nuts B; refit the cover checking that the tabs are fitted in their seat
and turning the fastener A counter-clockwise (for the left lid) or
clockwise (for the right lid) to hook it.
In the event of a failure (burnt-out bulbs) on taillights, brake lights
will switch on dimmed automatically in order to guarantee temporary
lighting at the back of the car.
After replacing the burnt-out bulb the taillights will operate regularly.
L0D0187m
L0D0188m

276
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
ADDITIONAL BRAKING LIGHT (THIRD STOP)
To change the bulb, proceed as follows:
❒open the tailgate and open the two tailgate covering hinge plugs A;
❒press the two fastening tabs B set inside the two holes to release
the light unit;
❒close the tailgate and remove the light unit;
❒press the two fastening tabs C and remove the bulb holder;
❒remove the snap-fitted bulbs and replace them. The bulbs are arranged inside the light unit as follows:
D: sidelights / STOP
E: direction indicators
F: reversing light
G: rear fog lights
L0D0189m
L0D0355m
L0D0356m