LAND ROVER DISCOVERY 1995 Workshop Manual

BRAKES
19
REPAIR SENSORS - REAR
Service repair no - 70.65.31
CAUTION: If a sensor is removed for any
reason, a NEW sensor bush must be fitted.
Remove
1.Disconnect battery negative lead.
2.Disconnect sensor electrical connections,
located above rear axle.
3.Remove sensor from its locating clip.
4.Remove bolts securing mudshield.
5.Using a suitable lever, pry sensor from mounting
bush.
6.Release harness cable ties, remove sensor lead
from vehicle.
7.Remove sensor bush.
Refit
8.Fit new sensor bush.
9.Lightly grease new sensor using silicone grease.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
10.Push sensor through bush until it touches exciter
ring. Sensor will be 'knocked back' to correct
position when vehicle is driven.
11.Secure harness in position.
12.Reconnect sensor electrical connection.
13.Drive vehicle to ensure ABS warning light is
extinguished.STOP LIGHT SWITCH ABS
Service repair no - 86.65.51
Remove
1.Turn ignition off. Disconnect battery negative
lead.
2.Remove lower trim panel.
3.Disconnect multiplug to switch.
4.Depress brake pedal access front of switch.
5.Pull sleeve and plunger of switch FULLY
forward.
6.Remove switch rearwards
NOTE: If switch is difficult to release,
check sleeve is FULLY forward.
Refit
7.Pull sleeve and plunger of switch fully forward.
8.Depress brake pedal, fit switch. Ensure retaining
clips are FULLY located.
9.Hold switch firmly in place, pull brake pedal back
fully to set switch.
10.Reconnect battery and turn ignition on.
11.Check switch operation by slowly depressing
brake pedal and checking that the switch clicks
twice.
12.Check stop lamps go off when pedal is released.
13.Recheck switch is securely fitted.
14.Operation may be checked using Testbook.

70BRAKES
20
REPAIR STOP LIGHT SWITCH - NON ABS
Service repair no - 86.65.51
Remove
1.Disconnect battery negative lead.
2.Remove lower dash panel.
3.Depress foot brake.
4.Remove rubber protector from switch, if fitted.
5.Remove hexagon nut.
6.Withdraw switch.
7.Disconnect electrical leads.
Adjust
8.With switch still in position and multiplug
disconnected, connect an ohmmeter across
switch terminals.
9.Screw switch in until open circuit exists across
terminals with pedal released and continuity
exists as soon as pedal is depressed.
10.Tighten locknut.
CAUTION: Ensure switch does not prevent
brake pedal returning fully.
Refit
11.Reverse removal procedure.

BRAKES
21
REPAIR BRAKE COMPONENTS ABS
Left hand drive shown. On right hand drive vehicles the master cylinder and servo unit only move
position.
KEY
1. Connector-double elbow
2. Rear left brake
3. Modulator to rear left brake
4. Modulator to master cylinder
5. Modulator to pressure reducing valve upper
6. Electrical connection
7. Modulator unit
8. Nut, mounting bush and cup
9. Modulator to front left brake
10. Front left brake
11. Electrical connection12. Modulator to front right brake
13. Modulator to pressure reducing valve lower
14. Master cylinder to pressure reducing valve lower
15. Front right brake
16. Bolt
17. Pressure reducing valve
18. Modulator to pressure reducing valve upper
19. Master cylinder
20. Servo unit
21. Modulator to rear right brake
22. Rear right brake

70BRAKES
22
REPAIR MODULATOR UNIT
Service repair no - 70.65.45
WARNING: New modulator units are
supplied in a shock absorbing pack
marked with a use by date. The new
modulator will contain hydraulic brake fluid within
the valve block and all ports plugged.
Modulator units must be handled with care the
following must be avoided:- any impact, use of
compressed air on any of the hydraulic ports,
removing plugs to connection ports before fitting
unit.
Remove
1.Refer to the illustration of brake components
ABS. For details of modulator unit and hydraulic
pipe connections to it.
See Brake
Components ABS
2.Refer to general brake service practice.See
General Brake Service Practice
3.Check new modulator unit is packaged in
accordance with the WARNING above.
4.Disconnect battery negative lead.
5.Remove the two electrical plugs.
6.Identify 8 pipe to modulator connections for
correct reassembly.
7.Disconnect 8 pipe unions.
8.Remove nuts securing modulator to mounting
bracket.
9.Remove modulator unit.
10.Remove mounting bushes and cup.
Refit
11.Fit mounting bushes and cup to new modulator.
12.Fit modulator unit to mounting bracket.
13.Fit 8 pipes to modulator connections. Pipes
mustbe connected to correct port. Tighten to
15Nm.
14.Bleed the complete hydraulic system.See
Brake System Bleed
15.Check system function using the 'Testbook'
diagnostics
16.Test operation of brakes.ELECTRONIC CONTROL UNIT ABS
Service repair no - 70.65.01
Remove
For location of the ECU.
See Description and
operation, ABS Components
1.Disconnect battery negative lead.
2.Remove retaining bolt and lower alarm system
ECU and relay mounting bracket into passenger
footwell.
3.Remove two screws and detach ECU complete
with harness plug from mounting bracket.
4.Release ECU plug retaining clip.
5.Move plug in direction of arrow and release
hooked end of plug from retaining post.
Refit
6.Reconnect ECU harness plug ensuring that it is
firmly located and retaining clip secures plug.
7.Reverse removal procedure.

BRAKES
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Brakes
Brake pipe connections to:
- Modulator unit 15.................................................................................
- Brake calipers 15.................................................................................
- Master cylinder 15................................................................................
Jump hoses to calipers 15..............................................................................
Bleed screws 15..............................................................................................
Brake caliper to swivel pin housing 82............................................................
Servo assembly to pedal box 26.....................................................................
Master cylinder to servo 26.............................................................................

BRAKES
1
SERVICE TOOLS BRAKE SERVICE TOOLS
LRT-70-500 Brake piston compressor
18G 672

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification, the vehicle is equipped
with alloy or pressed steel wheel rims, both using
tubeless radial ply tyres.
Tyre codes
The writing, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications.
See GENERAL SPECIFICATION
DATA, Information, Wheels and Tyres
1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure specification -
900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturer's brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
1
FAULT DIAGNOSIS TYRE WEAR CHART
FAULT CAUSE REMEDY
Rapid wear at Tyres under-inflated Inflate to correct pressure
shoulders Worn suspension components Replace worn components
i.e. ball joints, panhard
rod bushes,steering damper
Excessive cornering speeds
Rapid wear at
centreTyres over-inflated Inflate to correct pressure
of tread
Wear at one
shoulderTrack out of adjustment Adjust track to correct figure
Bent panhard rod Check and replace worn or damaged
components
Bald spots or tyre Wheel out of balance Balance wheel and tyre
cupping assembly
Excessive radial runout Check runout and replace tyre
if necessary
Shock absorber worn Replace shock
Excessive braking
Tyre scalloped Track out of adjustment Adjust toe to correct figure
Worn suspension components Replace as necessary
Excessive cornering speeds
CAUTION: This diagnosis chart is for general guidance only and does not necessarily include
every cause of abnormal tyre wear.

74WHEELS AND TYRES
2
FAULT DIAGNOSIS FAULT - SYMPTOMS
Vibration through steering wheel
1.Check tyre pressures.
See Repair, Tyre
Pressures
2.Check condition of tyres.See Tyre Wear Chart
3.Check front wheel alignment.See STEERING,
Adjustment, Front Wheel Alignment
4.Check wheel balance.See Repair, Wheel
Balancing
NOTE: In the event that any apparent
vibration is not eliminated at this stage.
See PROPELLER SHAFTS, Fault
diagnosis, Vibration Harshness
NOTE: In the event that any apparent
vibration is not eliminated at this stage, go
to steering Fault Diagnosis, Fault -
Symptom (Steering vibration, road wheel
shimmy/wobble).
See STEERING, Fault diagnosis,
Steering Faults
NOTE: Radial ply tyres have a flexible
sidewall, which produces a sidewall bulge
making the tyre appear under-inflated.
This is a normal condition for radial ply tyres. Do
not attempt to reduce this bulge by over-inflating
the tyre.
1. Correct inflation.
2. Under-inflation.
3. Over-inflation.
4. Tread contact with road.

WHEELS AND TYRES
1
REPAIR GENERAL INFORMATION
WARNING: This is a multi- purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures.
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels.The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim.
See
Tyre Fitting
WARNING: Do not fit an inner tube to an
alloy wheel.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment.
See Fault
diagnosis, Tyre Wear Chart
if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration below.
When the tread has worn to a remaining depth of 1.6
mm the indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration below.