warning LAND ROVER FREELANDER 2001 Manual PDF

DRIVESHAFTS
REPAIRS 47-3
Shaft with both joints - RH
$% 47.10.02
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove 3 bolts securing RH splash shield to
body and remove shield.
6.Release stake from drive shaft nut.
7.With assistant depressing the brake pedal,
remove and discard the drive shaft nut.8.Remove clip securing brake hose and release
hose from damper bracket.
9.Release ABS sensor harness and brake hose
from damper.
10.Release ABS sensor from hub.
11.Remove 2 bolts securing brake caliper to hub.
Release caliper from hub and tie aside.
CAUTION: Do not allow caliper to hang on
brake hose.

DRIVESHAFTS
REPAIRS 47-5
Gaiter - bell & joint - outer - front
$% 47.10.03
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - LH - front.
5.Slide gaiter from shaft.
Refit
1.Clean drive shaft.
2.Fit new gaiter to shaft.
3.Fit drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - LH - front.
4.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
5.Remove stands and lower vehicle.
6.Connect battery earth lead.
Bell & joint - outer - LH - front
$% 47.10.04
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.
5.Place drive shaft in vice.
6.Release both gaiter clips and discard.
7.Slide gaiter along shaft to gain access to outer
joint.
8.Using a drift against the inner part of the joint,
remove joint from shaft.
9.Inspect gaiter for damage and renew if
necessary.
Refit
1.Clean drive shaft and gaiter.
2.Fit new circlip to drive shaft.
3.Position outer joint to shaft, use a screwdriver
to press circlip into its groove and push joint
fully onto shaft.
4.Apply grease from the sachet to the joint.
5.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
6.Fit drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.
7.Fit front road wheels, fit and tighten nuts to 115
Nm (85 lbf.ft).
8.Remove stands and lower vehicle.
9.Connect battery earth lead.

DRIVESHAFTS
47-6 REPAIRS
Gaiter - inner joint
$% 47.10.16
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
bell & joint - outer - front.
5.Release both gaiter clips and discard.
6.Slide gaiter from shaft.
Refit
1.Clean drive shaft and gaiter.
2.Apply grease from the sachet to the joint.
3.Fit new gaiter to shaft.
4.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
5.Fit outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
bell & joint - outer - front.
6.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
7.Remove stands and lower vehicle.
8.Connect battery earth lead.
Shaft with both joints - rear
$% 47.11.01
Remove
1.Disconnect battery earth lead.
2.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Release stake from drive shaft nut.
5.With assistant depressing the brake pedal,
remove and discard drive shaft nut.
6.Remove nut and bolt securing trailing link to
rear hub, collect spacer from under bolt head.
7.Remove nut and bolt securing fixed transverse
link to subframe. Collect dynamic damper.
8.Remove nut and bolt securing adjustable
transverse link to subframe.
9.Position container to catch oil spillage

DRIVESHAFTS
47-8 REPAIRS
Gaiter - outer - rear
$% 47.11.03
Remove
1.Disconnect battery earth lead.
2.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - rear.
5.Slide gaiter from shaft.
Refit
1.Clean drive shaft and gaiter.
2.Apply grease from the sachet to the joint.
3.Fit new gaiter to shaft.
4.Fit drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - rear.
5.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
6.Remove stands and lower vehicle.
7.Connect battery earth lead.
Bell & joint - outer - rear
$% 47.11.04
Remove
1.Disconnect battery earth lead.
2.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - rear.
5.Place drive shaft in vice.
6.Release both gaiter clips and discard.
7.Slide gaiter along shaft to gain access to outer
joint.
8.Using a drift against the inner part of the joint,
remove joint from shaft.
9.Inspect gaiter for damage and renew if
necessary.
10.Remove and discard circlip from drive shaft.
Refit
1.Clean drive shaft and gaiter.
2.Fit new circlip to drive shaft.
3.Position outer joint to shaft, use a screwdriver
to press circlip into its groove and push joint
fully onto shaft.
4.Apply grease from the sachet to the joint.
5.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
6.Fit drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - rear.
7.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
8.Remove stands and lower vehicle.
9.Connect battery earth lead.

DRIVESHAFTS
REPAIRS 47-9
Gaiter - inner joint - rear
$% 47.11.16
Remove
1.Disconnect battery earth lead.
2.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
outer - rear.
5.Release both gaiter clips and discard.
6.Slide gaiter from shaft.
Refit
1.Clean drive shaft and gaiter.
2.Apply grease from the sachet to the joint.
3.Fit new gaiter to shaft.
4.Apply grease from the sachet to the joint.
5.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
6.Fit outer gaiter.

+ DRIVESHAFTS, REPAIRS, Gaiter -
outer - rear.
7.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
8.Remove stands and lower vehicle.
9.Connect battery earth lead.
Propeller shaft assembly
$% 47.15.01
Remove
1.Raise vehicle on a 4 post ramp.
2.Raise one wheel on each axle for rotation of
propeller shaft as necessary to access fixings.
CAUTION: When working on the propeller
shafts:
lAlways remove the propeller shafts and
viscous coupling as an assembly.
Dismantling the individual units on the
vehicle may cause damage to the
components.
lNever unbolt the viscous coupling
support bearings from the body without
first detaching the propeller shafts at the
differential and IRD. The weight of the
centre section will pull the CV joint apart,
causing irreparable damage.
lNever allow the CV joint to be
manipulated to an acute angle. This will
cause the internal roller bearings to
break up, leading to excessive backlash
and CV joint failure.
3.Reference mark the position of propeller shaft
flanges to IRD and rear axle flanges to aid
reassembly.
4.Remove 6 nuts, bolts and link washers
securing CV joint to IRD flange.

REAR AXLE & FINAL DRIVE
51-2 REPAIRS
Refit
1.With assistance position differential assembly
to subframe and locate in mountings, fit bolts
but do not tighten at this stage.
2.Position centralising jig LRT-51-013 to align
differential assembly.
3.Tighten forward bolts to 65 Nm (48 lbf.ft).
4.Tighten rearward bolts to 65 Nm (48 lbf.ft).
5.Remove LRT-51-013.
6.Connect breather pipe.
7.Position propeller shaft to rear axle and align
reference marks.
8.Fit and tighten nuts and bolt securing propeller
shaft to rear axle to 65 Nm (48 lbf.ft).
9.Fit drive shafts.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - RH.
10.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
Cover - rear - differential
$% 51.15.04
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Position container to catch oil spillage.
3.Remove oil level plug.
4.Remove 10 bolts securing rear cover to
differential casing.
5.Remove rear cover.
Refit
1.Clean rear cover, mating face on differential
and sealant from bolts and bolt threads.
2.Apply sealant, Part No. STC 3811 to casing
and fit rear cover.
3.Apply sealant, Part No. STC 50552 to threads
of rear cover bolts.
4.Fit rear cover bolts bolts and tighten by
diagonal selection to 25 Nm (18 lbf.ft).
5.Fill differential with oil.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
6.Fit level plug and tighten to 27 Nm (20 lbf.ft).
7.Remove stands and lower vehicle.

REAR AXLE & FINAL DRIVE
51-4 REPAIRS
Bush - differential mounting - rear
$% 51.15.44
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Position centralising jig LRT-51-013 to align
differential assembly.
3.Remove bolt securing differential mounting to
subframe.
4.Remove 2 bolts securing mounting to
differential.
5.Remove mounting.Refit
1.Position differential mounting.
2.Fit bolts securing mounting to differential and
tighten to 65 Nm (48 lbf.ft).
3.Fit bolt securing mounting to subframe and
tighten to 120 Nm (89 lbf.ft).
4.Remove LRT-51-013.
5.Remove stands and lower vehicle.

REAR AXLE & FINAL DRIVE
51-6 REPAIRS
Refit
1.Fit new collapsible spacer.
2.Fit pinion bearing and oil thrower.
3.Clean pinion flange and oil seal recess.
4.Fit new oil seal using LRT-51-010.
5.Fit pinion flange and washer.
6.Restrain pinion flange using LRT- 51-003.
7.Fit new pinion nut and tighten to 190 Nm (140
lbf.ft).
8.Check for end float on pinion. If end float exists
continue to tighten pinion nut until end float is
removed.
9.Continue to tighten pinion nut until correct
preload is obtained.
10.Pinion preload is 1.7 - 2.8 Nm (1.2 - 2.1 lbf.ft), if
higher replace collapsible spacer.
CAUTION: Do not tighten pinion nut to more
than 373 Nm (275 lbf.ft), or the collapsible
spacer will compress too far.
11.Clean propeller shaft flange and mating face.
12.Position propeller shaft to rear axle and align
reference marks.
13.Tighten propeller shaft nuts and bolts to 65 Nm
(48 lbf.ft).
14.Fit drive shafts.

+ REAR AXLE & FINAL DRIVE,
REPAIRS, Oil seal - differential housing.
15.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
Oil seal - differential housing
$% 51.20.36
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove bolt securing handbrake cable to
subframe.
4.Remove nut and bolt securing trailing link to
rear hub, collect spacer from under bolt head.
5.Remove nut and bolt securing fixed transverse
link to subframe. Collect dynamic damper.
6.Remove nut and bolt securing adjustable
transverse link to subframe.
7.Position drain tin to catch oil spillage.
8.With assistance pull hub assembly outwards.

STEERING
REPAIRS 57-5
REPAIRS
Power steering rack
$% 57.10.01
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove front road wheels.
3.Remove and discard nuts securing track rod
ball joints to steering arms.
4.Fit an M12 nut to each ball pin, flush with end of
each pin.
5.Using LRT-57-043, separate ball pins from RH
and LH steering arms. Remove M12 nuts and
release ball pins from steering arms.
6.Remove pinch bolt securing steering column to
PAS rack pinion.7. KV6 models: Remove 2 nuts securing steering
rack heat shield and remove heat shield.
8. KV6 models: Remove 2 bolts securing coolant
rail to cylinder block.
9. Td4 manual models: Using tool LRT-37-050
release gear change rods from gear change
linkage.
10. Td4 manual models: Remove 2 bolts securing
gearchange linkage to bulkhead and tie aside.

STEERING
57-14 REPAIRS
Pump - steering - K1.8
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Loosen PAS pump pulley bolts.
4.Remove PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
5.Position container to collect PAS fluid spillage.
6.Release clip and disconnect fluid inlet hose
from PAS pump.
CAUTION: Always fit plugs to open
connections to prevent contamination.
7.Loosen union securing fluid outlet pipe, release
outlet pipe remove and discard 'O' ring.
8.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.9.Remove 5 bolts securing PAS pump to
mounting bracket.
10.Remove PAS pump.
Refit
1.Position PAS pump and align to mounting
bracket.
2.Fit bolts securing PAS pump to mounting
bracket and tighten to 25 Nm (18 lbf.ft).
3.Fit PAS pump pulley and align bolts holes.
Ensure FRONT mark is facing outwards. Fit
bolts finger tight.
4.Remove plug from fluid outlet hose.
5.Clean PAS pump and pipe union.
6.Using a new 'O' ring, align outlet pipe and
tighten union to 20 Nm (15 lbf.ft).
7.Clean elbow on PAS pump.
8.Remove plug from fluid inlet hose, fit new clip
and connect hose to PAS pump.
9.Remove container.
10.Clean pulley 'V's and tensioner pulley running
surface.
11.Fit PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
12.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
13.Connect battery earth lead.
14.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
M57 1069
M57 1070