torque MAZDA 626 1987 Workshop Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 1987, Model line: 626, Model: MAZDA 626 1987Pages: 1865, PDF Size: 94.35 MB
Page 903 of 1865
TROUBLESHOOTING (G4A-EL) 7B
76G07B-036
Noise and vibration
Drive the vehicle in 2nd gear (Hold mode) and check for abnormal noise or vibration.
Note
Abnormal noise and vibration can also be caused by the torque converter, drive shaft or
differential. Therefore, checking of cause must be made with extreme care.
L Range Test
Shift pattern
1. Shift the selector lever to L range and select the mode.
2. Accelerate the vehicle and check that the 1-2 up- and down-shiftings are obtained and that no 3rd
gear, no OD, and no lock-up are obtained.
Note
Inspection of shift shock and shift point are not necessary because these are the same
as those of the D Range Test.
3. Drive in 1st gear then decelerate and check that engine braking effect is felt.
Note
a) In L range, the shift patterns for Economy and Power modes are the same.
b) Shift points are the same as those of the D range (Power) shift diagram.
4. While driving in S range (Hold mode) and 2nd gear, shift the selector lever to L range and check
that 2nd gear is held until the 2-1 down-shift point as shown in the L range (Hold) shift diagram
is achieved.
5. Accelerate the vehicle in L range (Hold mode) and check that 1st gear is held.
7B—37
Page 904 of 1865
7B TROUBLESHOOTING (G4A-EL)
86U07B-044
Noise and vibration
Drive the vehicle in 1st gear (Hold mode) and check for abnormal noise or vibration.
Note
Abnormal noise and vibration can also be caused by the torque converter, drive shaft or
differential. Therefore, checking of cause must be made with extreme care.
P Range Test
1. Shift into P range on a gentle slope, release the brake and check that the vehicle does not roll.
2. Shift into P range while driving the vehicle at maximum of 4 km/h (2.5 mph) on a level surface, and
check that the vehicle stops.
7B-38
Page 906 of 1865
7B TROUBLESHOOTING (G4A-EL)
Slippage Test
This step is performed to inspect slippage of the friction elements.
Preparation 1. Perform the preparation procedure shown in STEP 4 (STALL TEST). 2. Connect a tachometer to the engine and set it in the cabin.
3. Connect the EC-AT Tester and the adaptor harness between the EC-AT control unit and wiring
harness.
Procedure
Drive the vehicle in each of the gears indicated below and check whether the vehicle speed or engine
speed is above or below specification excessively as shown by the drum speed.
Driving condition
Speed
Drum speed (rpm)
No. Gears Other condition Speed
1,000 2,000 3,000 4,000
1 1st L range, Hold mode 11 (7) 22 (14) 33 (20) 44 (27)
2 1st D range, Economy mode 11 (7) 22 (14) 33 (20) 44 (27)
3 2nd S range, Hold mode Vehicle speed km/h (mph) 20 (12) 40 (25) 60 (37) 80 (50)
4 3rd D range, Hold mode 31 (19) 61 (38) 92 (57) 123 (76)
5 OD D range, Economy
mode 44 (27) 88 (55) 131 (81) 173 (107)
6 OD D range, Economy mode, Lock-up Engine speed (rpm) 1,000 2,000 3,000 4,000
76G07B-038
Evaluation
When there is no malfunction in the electrical system or hydraulic system, but vehicle speed or engine
speed is below specification, the problem can be attributed to slippage of the friction elements.
Driving conditions below specification Possible Cause
No.1 condition only Low and reverse brake
No.2 condition only One-way clutch
No.3 condition only 2-4 brake band
No.4 condition only Coasting clutch
No.5 condition only 3-4 clutch
No.1-No,5 conditions Forward clutch
No.6 condition only Lock-up piston (in torque converter)
76G07B-039
7B—40
Page 907 of 1865
TROUBLESHOOTING (G4A-HL) 7B
TROUBLESHOOTING (G4A-HL)
GENERAL NOTE
In the event of a problem with the automatic transaxle, the cause may be in the engine, power train,
hydraulic control system, or electrical control system.
When troubleshooting, therefore, it is recommended to begin from those points that can be judged
quickly and easily. The recommended troubleshooting sequence is described below.
STEP 4: TIME LAG TEST
Check time lag of oil pressure supply
STEP 6: OIL PRESSURE TEST Check line, throttle, and governor pressures
This step checks conditions surrounding the automatic
transaxle.
This step checks the electrical control system.
• Function of the electrical control system
• Components
This step checks the power train. • Friction element slipping • Torque converter capacity
This step checks operation of the hydraulic control system. • Accumulators • Friction elements slipping • Regulating valves
This step checks functions of the electric control system and
hydraulic control system.
This step checks major points of the hydraulic control system.
• Oil pump • Line pressure control • Throttle pressure control
• Governer pressure control
STEP 5: ROAD TEST Check items on road test
• Shift point • Shift schedule
• Kick-down • Shift shock • Lock-up and overdrive inhibition
By following the above 6 steps, the cause of the problem should be located.
As another guide to faster location of the causes of problems, the Quick Diagnosis Chart is included
at pages 7B—42, 43.
In this chart, a circle is used to indicate the components that might be the cause of trouble for 20
types of problems. It is only necessary to check those components indicated by circles, at each step
of the troubleshooting process, in order to quickly locate the cause of the problem.
76G07B-040
7B—41
Page 917 of 1865
TROUBLESHOOTING (G4A-HL) 7B
Evaluation
Condition Possible cause
Above specification
In all ranges Insufficient line pressure
Worn oil pump
Above specification
In all ranges Insufficient line pressure Oil leakage from oil pump, control valve, and/or transaxle case
Stuck pressure regulator valve
Above specification
In D 2, and 1 One-way clutch 1 slipping
Above specification
In D range only One-way clutch 2 slipping
Above specification In 2 range only 2-4 brake slipping Above specification
In R range only
Low and reverse brake slipping
Above specification
In R range only
Reverse clutch slipping
Above specification
In R range only Perform a road test, to determine if this is caused by the low and reverse brake or the reverse clutch, as follows:
a) Effective engine braking in 1 range Front clutch
b) No engine braking in 1 range Low and reverse brake
Within specification All shift control elements within transaxle are functioning
normally.
Below specification
Engine out of tune
Below specification One-way clutch slipping within torque converter
76G07B-055
7B—51
Page 920 of 1865
7B TROUBLESHOOTING (G4A-HL)
Noise and vibration
Drive the vehicle in OD (lock-up), OD (no lock-up), 3rd and check for abnormal noise or vibration.
Note
Abnormal noise and vibration can also be caused by the torque converter, drive shaft, or
differential. Therefore, checking of cause must be made with extreme care.
Kick-down
Drive the vehicle in OD, 3rd and 2nd gears and check that kick-down occurs for OD-*3, OD->2, 3-*2,
3->1, 2-> 1, and the shift points are as shown in the shift diagram.
2 Range Test
Shift pattern
1. Shift the selector lever to 2 range.
2. Accelerate the vehicle in 2 range and check that 2nd gear is held.
Noise and vibration
Drive the vehicle in 2nd gear and check for abnormal noise or vibration.
Note
Abnormal noise and vibration can also be caused by the torque converter, drive shaft or
differential. Therefore, checking of cause must be made with extreme care.
7B—54
Page 922 of 1865
7B TROUBLESHOOTING (G4A-HL)
F8 engine
8/8-1
7/8-
6/8-
O) I
i ! O) Q.
o 3/8- [ ^ I o
jE 2/8-1 I
1/8- |
0/8 ' 1 ' 1 ' 1 1 1 1 1 1— ' l 0 20 40 60 80 100 120 140 (12) (25) (37) (50) (63) (74) (87)
Vehicle speed km/h (mph)
76G07B-060
Noise and vibration
Drive the vehicle in 1st gear and check for abnormal noise or vibration.
Note
Abnormal noise and vibration can also be caused by the torque converter, drive shaft or
differential. Therefore, checking of cause must be made with extreme care.
P Range Test
1. Shift into P range on a gentle slope, release the brake and check that the vehicle does not roll.
2. Shift into P range while driving the vehicle at maximum of 4 km/h (2.5 mph) on a level surface,
and check that the vehicle stops.
Vehicle Speed at Gearshift Table
Range Throttle condition Shifting Vehicle speed km/h (mph) Range Throttle condition Shifting FE engine F8 engine
D
Fully opened 1st ->• 2nd 50-65 (31-40) 47-62 (29-38)
D
Fully opened 2nd - 3rd 100-115 (62-71) 94-109 (58—68)
D
Half throttle (1/2)
1st - 2nd 17-32 (11-20) 16—31 (10—19)
D
Half throttle (1/2) 2nd -> 3rd 42-57 (26-35)
D
Half throttle (1/2) 3rd -> OD 79-94 (49-58) 74-89 (46-55)
D
Half throttle (1/2)
Lock-up 74-89 (46-55) D
Kick-down
OD - 3rd More than 88 (55) More than 82 (51) D
Kick-down
OD -> 2nd 34-103 (21-64) 33-97 (20-60)
D
Kick-down OD - 1st 27-49 (17-30) 26-48 (16-30)
D
Kick-down 3rd - 2nd 34—103 (21-64) 33-97 (20-60)
D
Kick-down
3rd - 1st
11
-49 (7—30) 10-48 (6-30)
D
Kick-down
2nd - 1st
1st - 2nd
4-49 (2-30) 3-48 (2-30)
1
Fully opened
2nd - 1st
1st - 2nd 56-71 (35-44) 52—67 (32—42)
1 Half throttle (1/2) 1st - 2nd 56-71 (35-44) 52-67 (32—42) 1
Kick-down 2nd -> 1st 46-61 (29-38) 43-58 (27-36)
D Fully opened 3rd lock-up 106-121 (66—75) 100-115 (62-71)
7B-56
Page 932 of 1865
7B ELECTRICAL SYSTEM COMPONENTS
76G07B-073
7B-66
3. Remove the screw and move the inhibitor switch
so that the small hole is aligned with the screw hole.
4. Set the alignment by inserting a 2.0 mm (0.079
in) diameter pin through the holes.
5. Loosely tighten the switch mounting bolts, remove
the pin, and reinstall the screw.
6. Tighten the switch mounting bolts to specification.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
7. Recheck the continuity of the individual terminals.
WATER TEMPERATURE SWITCH
Inspection
1. Remove the water temperature switch.
2. Place the switch in water with a thermometer and
heat up the water gradually.
3. Check the continuity of the terminals. If necessary
replace the switch.
Connection guide
Water temperature Continuity
Below 65°C (149°F) Yes
Above 72°C (162°F) \ No
FLUID TEMPERATURE SWITCH (G4A-EL)
Inspection
1. Remove the fluid temperature switch.
2. Place the switch in oil with a thermometer as shown
and heat it up gradually.
3. Check the continuity of the terminals. If necessary
replace the switch.
Connection guide
Fluid temperature Continuity
Above 150°C (302°F) Yes
Below 143°C (289°F) No
BRAKE LIGHT SWITCH (G4A-EL)
Inspection of Terminal Voltage
1. Turn the ignition switch ON.
2. Check the voltage between terminal (WG) and
ground while depressing the brake pedal.
Terminal voltage I Brake pedal
Approx. 12V Depressed
Below 1,5V Released
3. If not correct, check continuity of the switch.
Page 938 of 1865
![MAZDA 626 1987 Workshop Manual
7B ON-VEHICLE MAINTENANCE
86U07B-064
86U07B-065
t «
•A
0 0
0 »
LX] O 9
m
(2)
(1)
Button need not
be depressed
Button must be pressed
76F07B-022
6. Ensure that the ATF level is be](/img/28/57059/w960_57059-937.png "MAZDA 626 1987 Workshop Manual
7B ON-VEHICLE MAINTENANCE
86U07B-064
86U07B-065
t «
•A
0 0
0 »
LX] O 9
m
(2)
(1)
Button need not
be depressed
Button must be pressed
76F07B-022
6. Ensure that the ATF level is be")
7B ON-VEHICLE MAINTENANCE
86U07B-064
86U07B-065
t «
•A
0 0
0 »
LX] O 9
m
(2)
(1)
Button need not
be depressed
Button must be pressed
76F07B-022
6. Ensure that the ATF level is between the F and L
marks. Add ATF to specification, if necessary.
Low temperature scale:
20°C (68°F)
High temperature scale:
65°C (149°F)
ATF type:
Dexron II or M HI
Inspection of Condition
1. Check the ATF for discoloration.
2. Check the ATF for any unusual smell.
Note
Determine whether or not the automatic trans-
mission should be disassembled by observ-
ing the condition of fluid carefully.
If the fluid is muddy and varnished, it indicates
burned drive plates.
SELECTOR LEVER
Inspection
1. Check that the selector lever can only be shifted
as shown in the figure.
2. Make sure there is a click at each range when shift-
ed from P <-> L or P <-» 1 range.
3. Check that the position of the selector lever and
the indicator are exact.
4. Check that the button returns smoothly when used
to shift the selector.
Adjustment
1. Loosen locknuts A, B, and lockbolt C.
2. Shift the selector lever to P range.
3. Shift the transaxle to P range by moving the man-
ual shaft of the transaxle.
4. While holding the selector lever forward in P range,
tighten lockbolt C to the specified torque.
Tightening torque:
8—11 N-m (80—110 cm-kg, 67—95 in-lb)
76F07B-023
7B—72
Page 939 of 1865
ON-VEHICLE MAINTENANCE 7B
76F07B-024
5. Turn locknut A by hand until it just touches the
spacer.
6. Tighten locknut B to the specified torque.
Tightening torque:
8—11 N m (80—110 cm-kg, 67—96 in-lb)
7. Shift the selector lever to N range.
8. With the button on the selector lever knob pressed,
push the selector toward R range with a force of
20 N (2 kg, 4.4 lb) and check the amount of move-
ment (a) at the selector lever knob.
9. Pull the selector lever toward D range in the same
manner and check the amount of movement (b).
10. Verify the stroke difference of (a) and (b) is as
specified.
Stroke difference: 8 mm (0.315 in) max.
Note
If not with in specification, readjust locknuts
A and B.
11. Check the selector lever operation.
(Refer to Inspection section.)
76F07B-025
THROTTLE CABLE
Inspection
1. Check the inner and outer cable for damage.
2. Make sure that the accelerator operates smoothly.
86U07B-066
Removal
1. Remove the battery and battery carrier.
2. Disconnect the main fuse block. (G4A-EL)
76G07B-090
7B—73