lock MAZDA 626 1987 Workshop Manual

REAR HATCH 1 4
REAR HATCH
STRUCTURAL VIEW
86U14X-022
1. Rear hatch
2. Upper trim
3. Side trim
4. Lower trim
5. Rear finisher
6. Rear hatch lock
7. Lock controller
8. Rear hatch outer handle
9. Stay damper
10. Key cylinder
11. Rear hatch screen
14—9

FRONT DOORS 1 4
86U14X-042
86U14X-043
69G14X-038
2. Remove the key cylinder spring.
3. Remove the key cylinder.
4. Remove the mounting nuts and remove the outer
handle.
Removal of Door Lock Assembly
1. Remove the mounting screws.
2. Remove the door lock assembly.
INSTALLATION
Install in the reverse order of removal, noting the fol-
lowing.
Power Window
Before installing the motor, connect the leads to a bat-
tery and run the regulator down to the position shown.
63U14X-035
14—17

1 4 FRONT DOORS
ADJUSTMENT
Door Lock Striker
1. Check that the door can be closed easily and
whether there is any looseness. If there is a prob-
lem, loosen the striker mounting screws and ad-
just by moving the striker down, or laterally.
2. Check the rear offset of the door to the body. If
there is a problem, adjust by moving the door lock
striker laterally.
86U14X-044
Door Hinge
1. If looseness is found when the door is opened,
tighten the door hinge mounting bolts (arrows).
2. Align the door and body by loosening and adjust-
ing the door hinge mounting bolts.
Note
If noise is heard from the checker when the
door is opened, apply grease to the checker
cam.
86U14X-045
14—18

REAR DOORS 1 4
REAR DOORS
STRUCTURAL VIEW
Sedan and Hatchback
86U14X-046
1. Regulator handle
(manual type)
2. Arm rest
3. Power window switch
4. Inner handle cover
5. Door trim
6. Belt line molding
7. Door screen
8. Door lock
9. Outer handle
10. Regulator (power type)
11. Regulator (manual type)
12. Glass guide
13. Glass
14. Weatherstrip
15. Weatherstrip
16. Door checker
17. Door
18. Weatherstrip
19. Sail inner garnish
20. Sail outer garnish
14—19

REAR DOORS 1 4
9. Remove the door glass upward.
86U14X-051
Remove the mounting bolts, and remove the win-
dow regulator through the service hole.
Remove the window motor mounting bolts, then
remove the motor from the regulator (power
window).
86U14X052
INSTALLATION
Install in the reverse order of removal, noting the fol-
lowing.
Tightening torque:
Nm (m-kg, ft-lb)
Door lock assembly 4.22-6 18 (0 43-0 63, 3,10—4.54)
Outer handle 8.8-13 (0.9-1.3. 6.5-9.4)
Glass Quide 7.8—11 (0.8—1.1, 5.8—8.0)
Regulator Nut 8 8—13 (0.9—1.3, 6.5—9.4) Regulator Bolt 7.8-11 (0.8-1.1. 5.8-8.0)
Door lock striker 18-26 (1.8-2.7, 13-20)
Before installing the motor, connect the leads to a bat-
tery and run regulator down to the position shown.
14—21

1 4 REAR DOORS
Installation of door lock and outer handle
1. Before installing the door lock, apply grease to the
places shown in the figure.
2. After installation, check that the door opens
smoothly, and that the operation of the lock is cor-
rect when using the key and the door lock knob.
86U14X-054
ADJUSTMENT
Door Lock Striker
1. Check that the door can be closed easily and
whether there is any looseness. If there is a prob-
lem, loosen the striker mounting screws and ad-
just by moving the striker vertically, or laterally.
2. Check the rear offset of the door to the body. If
there is a problem, adjust by moving the door lock
striker laterally.
86U14X-055
14—22

TRUNK-LID
LOCK REMOTE RELEASE
1
4
TRUNK-LID LOCK REMOTE RELEASE
REMOVAL AND INSTALLATION
1. Remove in the sequence shown in the figure.
2. Install in the reverse order of removal.
A 8 c D
1—
133
86U14X-108
1. Screws
2. Scuff plate
3. Screws
4. Cover
5. Bolts
6. Release lever
7. Release wire
14—45

SLIDING SUNROOF 14
(Cross-section C-C adjustment)
(1) Loosen the installation screw and the adjust
screw.
The adjustment will be easier if the installation
screw is not loosened too much.
(2) Adjust by moving the outer panel from the in-
side or outside.
(3) Tighten the adjust screw first, and then the in-
stallation screw.
76U14X-071
19. Measure the moving load of the panel, and adjust
it to 15—25 kg (33.1—55.7 lb) using the torque
adjustment nut on the motor.
20. To measure, use the deep hole in the center of the
lower panel.
76U14X-072
Adjusting torque nut
Pawl washer
21. After adjustment, be sure to lock the nut with the
pawl washer.
22. Install the ornamental cover.
23. Install the front peripheral parts.
76U14X-073
24. After installation is completed, check the operation.
(1) Is the battery voltage correct?
(2) Is there any foreign material on the sliding parts
of the sunroof?
(3) When the slide panel is opened, does the roof
panel interfere with the rear part? If so, open
the slide panel fully and move the set plate
forward.
76U14X-202
14—89

1 4 SEAT
69G14X-228
INSPECTION
Inspection of Front Seat
1. Check that the seat adjuster lever and recliner
knuckle lever move smoothly.
2. Check the seat mounting bolts for looseness. If
necessary, tighten the bolts to the specified torque.
Tightening torque:
Seat mounting bolt: 38—51 N-m
(3.9—5.2 m-kg, 28—38 ft-lb)
3. Apply grease to the moving parts.
4. Check the seat adjuster lever for wear.
REAR SEAT (Sedan and Coupe/MX-6)
Removal
1. Push the locks as shown in the figure to release
the cushion, then lift the seat cushion out.
76G14X048
2. Remove the end bolts, and lift the seat back off
the hooks.
69G14X-236
14—100
3. Remove the fastener.
4. Remove the seat back.
Installation
Install in the reverse order of removal.
Note
Tightening torque:
Seat back:
16—23 N-m (1.6—2.3 m-kg, 12—17 ft-lb)

SEAT BELTS
1
4
SEAT BELTS
STRUCTURAL VIEW
76G14X-032
1. Buckles 3. Rear seat belts 5. Retractors
2. Front seat belts 4. Retractors
INSPECTION
1. Check that the belt can be pulled out smoothly and
that it retractors lock when belt pulled quickly.
2. Inspect the webbing for scars, tears, and wear and
for deformation of the fittings.
Caution
Do not disassemble the buckle or ELR as-
sembly.
14—101