window MAZDA 626 1987 Owner's Guide

1 4 REAR HATCH GLASS
2. Carefully clean and remove any grease from a 5
cm (1.97 in) wide area around the circumference
of the glass and the remaining bond on the body.
3. Bond a dam along the circumference of the glass
8 mm (0.31 in) from the edge.
Caution
Securely bond the dam and let it dry.
63U14X-064
4. Apply primer with a brush to the circumference of
the glass and the body and
it
them to naturally dry
for 20 to 30 minutes.
Caution
Be sure not to allow dirt, water, oil, etc. to
come in contact with the coated surfaces and
do not touch it with your hand.
63U14X-065
5. When the primer has dried, apply an 11 mm (0.43
in) thick bead of repair seal (B001 77 739) 11 mm
(0.43 in) from the periphery of the window glass
using a sealant gun.
Caution
Cut the nozzle of the repair seal cartridge as
illustrated in the figure.
If necessary, smooth the repair seal to correct
any irregularities.
63U14X-067
6. Tighten the rear hatch glass mounting nuts.
Tightening torque:
2.9 N-m (30 cm-kg, 26 in-lb)
86U14X-142
14—60

1 4 QUARTER WINDOW GLASS
QUARTER WINDOW GLASS
STRUCTURAL VIEW
76G14X-024
1. Bolt
2. Rear side seatback
3. Screw (Hatchback)
Note
4. Package side shelf
(Hatchback)
5. Rear header trim screw
6. Rear pillar trim
7. Nuts
8. Quarter window molding
9. Quarter window glass
10. Dam
Use window tool set (49 0305 870A) to remove and install the glass.
14-62

QUARTER WINDOW GLASS 14
Coupe/MX-6
86U14X-149
1. Seat belt bolts
2. Screw
3. Screw
4. Side trim
5. Screw
6. Rear pillar trim
7. Nut
8. Screw
9. Drip molding
10. Quarter window molding
11. Quarter window glass
12. Dam
14-63

14 QUARTER WINDOW GLASS
76G14X-025
86U14X-151
86U14X-152
7mm
0.27in)
t
a H
t
U
n #
Quarter window
glass
REMOVAL
1. Fold down the rear seatback, and remove the rear
side seatback. (Hatchback)
2. Remove the luggage compartment cover and the
package side shelf. (Hatchback)
3. Remove the seat bolts.
4. Remove the rear pillar trim.
5. Remove the mounting nut and fastener, and re-
move the quarter window molding.
6. Make a small hole through the sealant.
7. Pass the piano wire through the hole.
8. Wind each end of the wire around a bar.
9. Pull the wire to and fro, and saw through the seal-
ant around the edge
of
the glass. Then remove the
glass.
Caution
a) Use a long sawing action to spread the work
over the whole length of wire to prevent it
from breaking.
b) Be careful that the wire does not rub on the
vehicle paint.
INSTALLATION
1. Use the knife to smoothly cut the sealant on the
body side, leaving a layer about
1
or 2 mm (0.04
to 0.08 in) thick.
2. Carefully clean around the edge of the quarter win-
dow glass (up to approx. 5 cm (0.2 in) from the
edge), and the adhesion surface at the body side.
3. Attach a dam (G043 50 762) around the glass, ap-
prox. 7 mm (0.28 in) from the edge.
86U14X-153
14-64

QUARTER WINDOW GLASS 1 4
4. Apply a thin coat of primer to the bonding area of
the body and glass, and allow 30 minutes for it
to dry.
Caution
Keep the area free of dirt. Do not touch the
surface. If primer gets on the hands, remove
it immediately.
86U14X-154
Repair
seal
lOver 10mm
\> " fl(Q.4iri)
J -Quarter
window glass
5. After the primer dries, apply a bead of repair seal
to a height of 10 mm (0.4 in) min. around the
edge of the glass.
86U14X-155
6. Attach the glass to the body.
86U14X-157
14-65

14 QUARTER WINDOW GLASS
14—66
Check for water leaks. If a leak is found, wipe the
water off well and add repair seal (B001 77 739).
Install in the reverse order of removal.

14 REAR WINDOW WIPER
REAR WINDOW WIPER
STRUCTURAL VIEW (HATCHBACK)
76G14X-031
1. Wiper arm and blade 3. Wiper motor 5. Hose
2. Seal cap 4. Washer tank 6. Washer nozzle
14—94

REAR WINDOW WIPER 14
86U14X-176
86U14X-178
REMOVAL
1. Disconnect the negative battery cable.
2. Remove the wiper arm.
3. Open the rear hatch.
4. Remove the rear hatch trim (upper, side and lower).
5. Remove the rear hatch screen.
Note
Remove the screen carefully so that it may be
reused.
6. Disconnect the rear wiper motor connector.
7. Remove the rear wiper motor.
INSTALLATION
Install in the reverse order of removal.
86U14X-179
14—95

14 REAR WINDOW WIPER
(0.98 ±0.19 in)
ADJUSTMENT
Arm Height
Set the height as shown in the figure.
86U14X-180
o
r ^
660 mm
(25.98 in)
Adjustment of washer spray
Insert a needle or similar object into the nozzle hole
and bend to change the spray direction.
86U14X-181
14—96

15
BODY ELECTRICAL SYSTEM
INTRODUCTION 15- 2 HOW TO USE THIS SECTION 15— 2 ELECTRICAL TROUBLESHOOTING TOOLS 15- 2 PRECAUTION 15— 3 ELECTRICAL SYMBOLS 15- 6 LOCATION OF UNIT, RELAY AND SWITCH 15- 7
STRUCTURAL VIEW 15— 7 MAIN FUSE BLOCK 15- 9 STRUCTURAL VIEW 15— 9 REPLACEMENT 15—10 IGNITION SWITCH 15—10
INSPECTION 15— 10 JOINT BOX AND FUSE 15—11
STRUCTURAL VIEW 15—11
COMBINATION SWITCH 15-12 STRUCTURAL VIEW 15- 12 INSPECTION 15— 13 CLUSTER SWITCH 15—17 STRUCTURAL VIEW 15— 17 INSPECTION OF ROCKER TYPE 15— 19
INSPECTION OF PUSH TYPE 15— 20 METER 15— 22 STRUCTURAL VIEW 15— 22 DISASSEMBLY AND ASSEMBLY 15— 23
TROUBLESHOOTING 15— 24 INSPECTION OF ANALOG METER .... 15— 26 INSPECTION OF DIGITAL METER 15— 27
INSPECTION OF METER SENDER 15— 29 WARNING LIGHT AND SENDER 15- 31 CIRCUIT DIAGRAM 15— 31
TROUBLESHOOTING 15- 32 INSPECTION 15— 39 CENTRAL PROCESSING UNIT 15— 41 STRUCTURAL VIEW 15— 41 FUNCTIONS 15- 41 CIRCUIT DIAGRAM 15— 42 REMOVAL AND INSTALLATION 15— 43
ON-VEHICLE INSPECTION 15- 43 TURN AND HAZARD LIGHT 15- 44 STRUCTURAL VIEW 15— 44 CIRCUIT DIAGRAM 15— 45
TROUBLESHOOTING 15- 46 INSPECTION 15— 47 STOP LIGHT 15— 48
STRUCTURAL VIEW 15— 48 CIRCUIT DIAGRAM 15— 49
TROUBLESHOOTING 15- 49 INSPECTION 15- 50 HORN 15— 52 STRUCTURAL VIEW 15— 52 CIRCUIT DIAGRAM 15— 52 TROUBLESHOOTING 15— 53 INSPECTION 15-53 HEADLIGHT 15— 54 CIRCUIT DIAGRAM 15— 54 TROUBLESHOOTING 15— 54 INSPECTION 15— 55 PANEL LIGHT CONTROL 15— 56 CIRCUIT DIAGRAM 15— 56
TROUBLESHOOTING 15_ 5fi INSPECTION 17 REAR WINDOW DEFROSTER ..i".'! 15- 58
STRUCTURAL VIEW 15-5fl CIRCUIT DIAGRAM 15_ «
TROUBLESHOOTING '.. 15_ 59
INSPECTION
15-60 POWER WINDOW 15-61 STRUCTURAL VIEW il_ «1 CIRCUIT DIAGRAM 15_ 62 TROUBLESHOOTING 15- «3 INSPECTION 15-66 REMOTE CONTROL MIRROR ........15- 69 STRUCTURAL VIEW 15-69 CIRCUIT DIAGRAM 15_ 69
TROUBLESHOOTING 15_ 70 INSPECTION 15_ 70 REAR WINDOW WIPER 15_ 71 STRUCTURAL VIEW 15-71 CIRCUIT DIAGRAM .'.'.'...' 15_ 72
TROUBLESHOOTING 15-73 INSPECTION 15-75 WINDSHIELD WIPER 15-76 STRUCTURAL VIEW ' ' 15— 7e
DISASSEMBLY AND ASSEMBLY OF WIPER MOTOR 15_ 76 CIRCUIT DIAGRAM 15-77 TROUBLESHOOTING " " 15— 70 INSPECTION 15-81 CRUISE CONTROL SYSTEM 15- 82 STRUCTURAL VIEW 15-82 CIRCUIT DIAGRAM 15-83 ON-VEHICLE INSPECTION \..\m 15- 84 INSPECTION 15-87 SLIDING SUNROOF 15-89 STRUCTURAL VIEW 15_ 89 CIRCUIT DIAGRAM i5_ 90
TROUBLESHOOTING 15— 91 INSPECTION 15_ 90 AUTO ADJUSTING SUSPENSION 15— 94
CIRCUIT DIAGRAM 15- 94
TROUBLESHOOTING GUIDE 15— 94
TROUBLESHOOTING 15— 94
INSPECTION 15-104
POWER DOOR LOCK 15-105
STRUCTURAL VIEW 15-105
CIRCUIT DIAGRAM 15-105
TROUBLESHOOTING 15-106 INSPECTION 15-107 AUDIO SYSTEM " 15_108 OUTLINE OF AUDIO SYSTEM 15-108 REAR CONNECTOR VIEW 15-109 ADJUSTMENT (MTR) 15—114 POWER ANTENNA 15-114 HEATER J
STRUCTURAL VIEW 15-116 AIR FLOW AT EACH MODE 15-117 RATE OF AIR FLOW 15-119 LEVER CONTROL TYPE 15-120 LOGICAL CONTROL
TYPE
15—121 LOGICON SWITCH 15—123
76G15X-001