check oil MAZDA 626 1987 Repair Manual

OIL PUMP 2A
DISASSEMBLY
Disassemble in the sequence shown in the figure. 69G02B-012
1. Pump cover
2. Outer gear
3. Inner gear
4. Pressure relief
valve
5. Oil seal
6. Oil pump body
76G02A-018
INSPECTION
(DOHC)
1. Check the following and replace any faulty parts.
(1) Distorted or damaged oil pump body or cover
(2) Worn or damaged plunger
(3) Weak or broken plunger spring
2. Measure the side clearance.
Clearance: 0.10 mm (0.004 in) max.
76G02A-019
3. Measure the tooth tip clearance.
Clearance: 0.18 mm (0.007 in) max.
69G02B-015
2A-11

2A OIL PUMP
86U02X-021
76G02A-020
76G02A-021
4. Measure the outer gear to pump body clearance.
Clearance: 0.20 mm (0.008 in) max.
(SOHC)
1. Check the following and replace any faulty parts.
(1) Distorted or damaged oil pump body or cover
(2) Worn or damaged plunger
(3) Weak or broken plunger spring
2. Measure the side clearance.
Clearance: 0.10 mm (0.004 in) max.
3. Measure the outer gear tooth tip and crescent
clearance.
Clearance: 0.35 mm (0.014 in) max.
4. Measure the inner gear tooth tip and crescent
clearance.
Clearance: 0.40 mm (0.016 in) max.
76G02A-022
2 A—12

INSPECTION 2B
A
76G02B-006
INSPECTION
ENGINE OIL
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temper-
ature and stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil lev-
el and condition.
5. Add or replace oil if necessary.
Note
The distance between the L and F marks on
the level gauge represents 1.2 liters (1.26 US
qt, 1.05 Imp qt).
OIL PRESSURE
1. Disconnect the oil hose (vacuum pump—cylinder
block).
76G02B-007
2. Set the SST as shown.
3. Remove the vacuum pump drive belt to prevent
heat damage to bearing.
4. Warm up the engine to normal operating tem-
perature.
76G02B-008
5. Run the engine first at 1,000 rpm, then at 3,000
rpm and note the gauge reading.
Standard oil pressure kPa (kg/cm2, psi)

1,000 rpm 147-245 (1.5-2.5, 21-36)
3,000
rpm
343—441 (3.5-4.5, 50—64)

6. If the pressure is not as specified, check for the
cause, and repair if necessary.
(Refer to Troubleshooting Guide.)
76G02B-009
2B—5

2B
ENGINE OIL, OIL
FILTER
86U02X-006
76G02B-010
86U02X-008
ENGINE OIL
REPLACEMENT
1. Warm up the engine to the normal operating tem-
perature and stop it.
2. Remove the oil filler cap and the oil pan drain plug.
3. Drain the oil into a suitable container.
Warning
Be careful when draining, the oil is very hot.
4. Install the drain plug and a new gasket.
Tightening torque:
29—41 N-m (3.0—4.2 m-kg, 22—30 ft-lb)
5. Refill the engine with the specified type and amount
of oil.
6. Refit the oil filler cap.
Oil pan capacity:
5.0 liters (5.3 US qt, 4.4 Imp qt)
7. Recheck the oil level after the engine has been run.

OIL
FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface
on the engine.
3. Apply a coat of engine oil to the filter rubber seal.
4. Install the oil filter until the rubber seal contacts the
oil cooler by hand. Then tighten it a 7/6 turn fur-
ther with a band type wrench.
5. Start the engine and inspect around the filter seal
for leaks.
6. Check the oil level and add oil if necessary.
Oil filter capacity:
0.50 liters (0.52 US qt, 0.44 Imp qt)
76G02B-011
2B—6

OIL
COOLER AND
OIL
FILTER BODY 2B

OIL
COOLER AND
OIL
FILTER BODY
REMOVAL
1. Disconnect the battery negative cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure.
76G02B-012
76G02B-013
1. Idler pulley
2. Water hose
3. Connector bolt
4. Oil cooler
5. Oil filter
6. Oil filter cover
7. Oil filter body
8. Plug
9. Pressure spring
10. Plunger control
11. Relief valve spring
12. Steel ball
INSPECTION
1. Inspect the oil cooler body for cracks or corrod-
ed. If necessary replace it.
2. Check the valves for damage or scoring if neces-
sary replace it.
3. Measure free length of each valve spring. If neces-
sary replace it.
Free length
Relief valve spring: 45.5 mm (1.79 in)
Pressure spring : 54.6 mm (2.15 in)
76G02B-014
2B-7

2B
OIL
COOLER AND
OIL
FILTER BODY
76G02B-015
76G02B-016
INSTALLATION
1. Apply a coat of engine oil to the valve holes.
2. Install the relief valve spring and pressure spring.
Tightening torque:
20—29 Nm (2.0—3.0 m-kg, 14—22 ft-lb)
3. Clean the contact surfaces of the cylinder block
and oil filter body.
4. Install new O-rings and apply a coat of engine oil.
5. Install the oil filter body.
Tightening torque:
Bolt A: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
Bolt B: 37—52 N-m
(3.8—5.3 m-kg, 27—38 ft-lb)
76G02B-017
6. Apply a coat of engine oil to the O-rings.
7. Install the oil cooler with new O-ring on the con-
nector bolt.
Tightening torque:
25—34 N-m (2.5—3.5 m-kg, 18—25 ft-lb)
8. Connect the water hoses.
9. Install the oil filter cover.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
10. Install the oil filter. (Refer to page 2B—6)
11. Install the idler pulley.
Tightening torque:
19—26 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
12. Install the Comprex supercharger drive belt and
adjust the belt deflection. (Refer to page 1C—7)
13. Add specified amount of coolant and engine oil.
14. Check for leaks.
76G02B-018
2B—8

2B OIL PAN
INSPECTION
Check the following points. Repair or replace if
necessary.
1. Cracks, deformation, damage
2. Damaged drain plug threads
4BG02X-037
76G02B-022
INSTALLATION
Install in the reverse order of removal referring to in-
stallation note.
Installation Note
Stiffener (RF-CX)
1. Remove any dirt or other material from the con-
tact surfaces.
2. Apply a continuous bead of silicone sealant to the
stiffener along the inside of the bolt holes, and over-
lap the end.
3. Install the stiffener.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
Oil Strainer
Install the oil strainer and a new gasket.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
76G02B-023
2B—10
Oil Pan
Remove any old sealant from the bolts and bolt holes.
If old sealant can not be removed from the bolt, re-
place it.
Without gasket
(1) Remove any dirt or grease from the contact
surfaces with a rag.
(2) Apply continuous bead of silicon sealant to the
oil pan along the inside of the bolt holes, and
overlap the ends.
(3) Install the oil pan.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)

OIL PUMP 2B
DISASSEMBLY
Disassemble in the sequence shown in the figure. 69G02B-012
INSPECTION
1. Check the following and replace any faulty parts.
(1) Distorted or damaged oil pump body or cover
(2) Worn or damaged plunger
(3) Weak or broken plunger spring
2. Measure the side clearance.
Clearance:
0.14 mm (0.006 in) max.
3. Measure the tooth tip clearance.
Clearance: 0.24 mm (0.009 in) max.
2B-13

OIL JET 2B
OIL JET
REMOVAL
Remove each part in the following order.
1. Remove the oil pan. (Refer to page 2B—9).
2. Remove the oil jet valve.
3. Remove the oil jet.
76G02B-034
INSPECTION
1. Make sure that the oil passage is not clogged.
2. Check that the oil jet valve is not stuck or damaged.
INSTALLATION
Install in the reverse order of removal.
Tightening torque: 12—18 N-m
(1.2—1.8 m-kg, 104—156 in-lb)
76G02B-035
2B—15

COOLANT 3A
76G03A-016
69G03A-006
COOLANT
INSPECTION
Coolant Level (Engine cold)
1. Check that the coolant level is near the radiator inlet
port.
2. Check that the coolant level in the coolant reser-
voir is between the FULL and LOW marks.
Add coolant if necessary.
Warning
a) Never remove the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
removing it.
Coolant Quality
1. Check that there is no build-up of rust or scales
around the radiator cap or radiator filler neck.
2. Check that coolant is free from oil.
3. Replace the coolant, if necessary.
Coolant Leakage
1. Connect a tester and SST to the radiator inlet port.
2. Apply 103 kPa (1.05 kg/cm2, 15 psi) pressure
to the system.
3. Check that the pressure is held.
If not, check for coolant leakage.
Warning
When removing either the radiator cap or the
tester, loosen it slowly until the pressure in
the radiator is released, and then remove it.
86U03X-005
REPLACEMENT
1. Remove the radiator cap and loosen the drain plug.
2. Drain the coolant into a suitable container.
Warning
a) Never open the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
loosening.
c) Use caution when draining hot coolant.
86U03X-006
3A-5