torque MAZDA PROTEGE 1992 Owners Manual

B2 INSTALLATION
L I I
03UOBZ-132
03UOB2-1 34
Engine and transaxle assembly
1. Suspend the engine and transaxle assembly.
Caution
l Do not damage any components in the engine com-
partment.
2. Install the engine and transaxle assembly in the engine
3. ii?the engine mounts with the engine mount member
mounting holes.
Engine mount
1. Install the engine mount nuts of the No.2 and No.3 mounts
and tighten them.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
2. Install the No.3 engine mount rubber.
Tightening torque
@j: 74-103 N-m (7.5-10.5 m-kg, 54-76 ft-lb)
@: 67-93 N-m (6.8-9.5 m-kg, 49-69 ft-lb)
3. Install the dynamic damper.
Tightening torque:
55-80 N-m (5.6-8.2 m-kg, 41-59 ft-lb)
Caution
l Before installing the engine support bracket, ar-
range the clutch release cylinder and pipe assembly.
4. Install the engine support bracket (MTX).
Tightening torque:
55-80 N-m (5.6-8.2 m-kg, 41-59 ft-lb)
5. Install the No.4 engine mount rubber and bracket, and
loosely tighten nuts @
6. Install bolts @ on the body side, and tighten them in two
or three steps in the order shown.
Tightening torque:
43-61 N-m (4.4-6.2 m-kg, 32-45 ft-lb)
7. Tighten nuts @.
Tightening torque:
67-93 N-m (6.8-9.5 m-kg, 49-69 ft-lb)

INSTALLATION
Step 3
Torque Specifications
16-23 (1.6-2.3, 12-17) 6.9-9.8 N.m (70-100 cm-kg, 61-87 in-lb)
I

m- ,,
// / 31-46 (3.2-4.7, 23-34)
ATX
Y
16-23 (1.6-2.3, 12-17) I 37-52 (3.8-5.3, 27-38) \/r-]z$/ 43-59 (4.4-6.0, 31-43)
COTTER PIN, NEW
/ 31-46 (3.2-4.7. 23-34) 42-67 (4.3-5.8, 31-42)
-_ ..------_ N.m (m-kg, R-lb)
no, Inor, 1.3
L 03UOB2 131
I 0311082-13.
Driveshaft
1. Apply grease to the end of the driveshaft.
Caution
l When installing the driveshaft, be careful not to
damage the oil seal.
l After installation, pull the front hub outward to con-
firm that the driveshaft is securely held by the clip.
2. Install the driveshaft and a new clip.
3. Install the lower arm ball-joint to the knuckle; then tighten
the lock nut.
Tightening torque:
43-59 N-m (4.4-6-O m-kg, 31-43 ft-lb)
4. Install the joint shaft.
5. Tighten the bolts in the order shown.
Tightening torque:
42-62 N-m (4.3-6.3 m-kg, 31-46 ft-lb)
82-97

B2 INSTALLATION
I 1
OBUOEP-138
I
J 13UOB2-024
Tie-rod end
1. Install the tie-rod end to the knuckle.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
2. Install the new split pin.
Stabilizer
1. Install and adjust the stabilizer.
Dimension A: 17-19mm (0.87-0.75 in)
Extension bar (MTX)
1. Install the extension bar to the transaxle.
Tightening torque:
31-48 N#m (3.2-4.7 m-kg, 23-34 ft-lb)
Shift control rod (MTX)
1 Install the shift control rod to the transaxle.
Tightening torque:
18-23 N-m (1.8-2.3 m-kg, 12-17 ft-lb)
Clutch release cylinder (MTX)
1. Install the clutch release cylinder.
Tightening torque:
16-23 N#m (1.6-2.3 m-kg, 12-17 ft-lb)
2. Set the pipe bracket in position.
Tightening torque:
18-23 N-m (1.6-2.3 m-kg, 12-17 ft-lb)
Shift control cable (ATX)
1. Install the shift control cable to the transaxle.
Tightening torque:
6.9-9.8 N-m (70-100 cm-kg, 61-87 in-lb)
03UOB2-142
B2-98

INSTALLATION
Step 4
I. Connect the hoses shown in the figure.
Caution Speedometer cable
1. Install the speedometer cable.
Exhaust pipe
1. Install the exhaust pipe and a gasket; then loosely tighten
the lock nuts.
2. Loosely tighten the bracket bolts.
3. Tighten the lock nuts.
Tightening torque:
31-46 N-m (3.2-4.7 m-kg, 23-34 ft-lb)
4. Tighten the bracket bolts.
Tightening torque:
37-52 N.m (3.8-5.3 m-kg, 27-38 ft-lb)
l Position the hose clamp in the original location on the hose, and squeeze the clamp lightly
with large pliers to ensure a good fit.
VACUUM HOSE
(CRUISE CONTROL) BRAKE, VACUUM HOSE 1 VACUUM HOSE
(PURGE CONTROL)
HEATER HOSE
FUE’L HOSE
03UOB2-14
B2-9:

B2 INSTALLATION
Step 5
1. Connect the harness connectors shown in the figure.
___---
r-
OIL PRESSURE SWITCH
THROTTLE
GROUND ITX
INHIBITOR SWITCH
TRAL SWITCH (MTX)
7.6-11 N.m
I N.m
0 cm-kg, 69-95 in-lb)
2.9-5.9 N-m
30-60 cm-kg,
26-52 in-lb)
cm-kg, 56-82 in-lb) 03UOB2-1~
Step 6
Torque Specifications
7.6-11 N.m (60~110 cm-kg, 69-95 in-lb)
N-m (m-kg, ft-lb]
03UOB2-14
.-
-’
82-l 00

INSTALLATION
03UOB2-141
/ 03UOB2-14!
1 03UOB2-150
03UOB2-151
8,’
1
a : :“.;,
.’
s,::, ; i .:.;...
..:.a.. :..,:.
. .
. .
” . : 0 ,.: ::
: .:.. ..,
., ‘:;
.<.,:.,);
‘zi :
I 0311082-152
A/C compressor (If equipped)
1. Install the A/C compressor.
Tightening torque:
24-35 N,m (2.4-3.6 m-kg, 17-26 ft-lb)
2. Tighten the A/C pipe bracket to the engine mount member.
Tightening torque:
6.4-9.3 N-m (65-95 cm-kg, 56-62 in-lb)
P/S oil pump and bracket
1. Install the P/S oil pump and bracket.
Tightening torque:
37-52 N.m (3.8-5.3 m-kg, 27-38 ft-lb)
Drive belt
1. Install the P/S and/or A/C drive belt.
2. Adjust the drive belt deflections. (Refer to page B2-6.)
Radiator and cooling fan assembly
1. Install the radiator and cooling fan assembly.
Tightening torque:
7.8-11 N-m (80-110 cm-kg, 69-95 in-lb)
2. Connect the upper and lower radiator hoses.
Caution
l Position the hose clamp in the original location on
the hose, and squeeze the clamp lightly with large
pliers to ensure a good
fit.
3. Connect the coolant reservoir hose.
4. Connect the cooling fan connector.
5. Connect the oil cooler hose. (ATX)
B2-101

92 INSTALLATION
RESOiANCE CHAMBER
03UOBZ-154
Accelerator cable
1. Install the accelerator cable.
2. Adjust the cable deflection by turning nut A.
Deflection: 1-3mm (0.04-0.12 in)
Battery duct, battery carrier, and battery
1. Install the battery duct.
Tightening torque:
7.8-l 1 Nlm (80-l 10 cm-kg, 69-96 In-lb)
2. Install the battery carrier.
Tightening torque:
7.8-l 1 N*m (80-l 10 cm-kg, 69-96 in-lb)
3. Install the battery and the battery bracket.
Tightening torque:
2.9-5.9 N*m (30-60 cm-kg, 26-52 in-lb)
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 N#m (1.9-2.6 m-kg, 14-19 ft-lb)
@: 7.8-l 1 N*m (80-l 10 cm-kg, 69-95 In-lb)
2. Connect the air flow sensor connector.
Resonance chamber
I, Install the resonance chamber.
Tightening torque:
7.8-l 1 N#m (80-l 10 cm-kg, 69-95 In-lb)
Under cover and side cover
1. Install the under cover and side cover.
Steps After Installation
1. If the engine oil was drained, fill with the specified amount and type of engine oil.
(Refer to Section D.)
2. Fill the radiator with the specified amount and type of engine coolant.
(Refer to Section E.)
3. If the transaxle oil was drained, fill with the specified amount and type of transaxle oil.
(Refer to Sections J2, K.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage.
(2) ignition timing, idle speed. (Refer to page 82-8.)
(3) Operation of emission control system.
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
B2-102
2311082.047

D OIL PRESSURE
OIL PRESSURE
PREPARATION
SST
49 C 187 280
Gauge,
oil pressure
03UODX-03
2
03UODX-007
INSPECTION
1, Remove the intake manifold bracket.
2. Remove the oil pressure switch.
3. Screw the SST into the oil pressure switch installation hole.
4. Warm up the engine to normal operating temperature.
5. Run the engine at 1,000 rpm and 3,000 rpm, and note the
gauge reading.
Oil pressure:
196-294 kPa (2.0-3.0 kg/cm2, 28-43 psi)-1,000 rpm
294-392 kPa (3.0-4.0 kg/cm2, 43-57 psi)-3,000 rpm
6. If the pressure is not as specified, check for the cause and
repair. (Refer to Troubleshooting Guide.)
7. Remove the SST and install the oil pressure switch.
Tightening torque:
12-18 N-m (1.2-l .8 m-kg, 104-156 in-lb)
8. Install the intake manifold bracket.
Tightening torque
@: 37-52 N*m (3.8-5.3 m-kg, 27-38 ft-lb)
0: 19-25 N,m (1.9-2.6 m-kg, 14-19 ft-lb)

ENGINE OIL, OIL FILTER D
b
I
03UODX-00
ONODX-01
r
03UODX-011
ENGINE OIL
INSPECTION
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temperature and
stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil level and con-
dition.
5. Add or replace oil as necessary.
Note
l The distance between the L and F marks on the level
gauge represents 0.8 liter (0.85 US qt, 0.70 Imp qt).
REPLACEMENT
Warning
l Be careful when draining; the oil is hot.
1. Warm up the engine to normal operating temperature and
stop it.
2. Remove the oil filler cap and the oil pan drain plug.
3. Drain the oil into a suitable container.
4. Install a new gasket and the drain plug.
Tightening torque:
29-41 N,m (3.0-4.2 m-kg, 22-30 ft-lb)
5. Refill the engine with the specified type and amount of en-
gine oil.
6. Refit the oil filler cap.
7. Run the engine and check for leaks.
8. Check the oil level and add oil if necessary.
Oil pan capacity
B6 SOHC
BP SOHC and DOHC
liters (US qt, Imp qt)
3.0 (3.2, 2.6)
3.6G.843.2)
w
03UODX-011
D-7

D OIL FILTER, OIL COOLER
r
\/
OSUODX-0
‘I . 03UODX-01
OIL FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface on the
engine.
3. Apply a small amount of clean engine oil to the rubber seal
of the new filter.
4. Install the oil filter and tighten it by hand until the rubber
seal contacts the base.
5. Tighten the filter 1 and 116 turns with a filter wrench.
6. Start the engine and check for leaks.
7. Check the oil level and add oil if necessary.
Oil filter capacity: 0.17 liter (0.18 US qt, 0.15 Imp qt)
OIL COOLER (BP DOHC)
REMOVAL
1. Drain the engine oil.
2. Remove the oil filter with an oil filter wrench.
3. Disconnect the water hoses.
4. Remove the oil cooler.
INSTALLATION
1. Install the oil cooler.
Tightening torque:
29-39 Nnrn (3.0-4.0 m-kg, 22-29 ft-lb)
2. Install the oil filter. (Refer to page D-8.)
3. Add engine oil to the correct level.
4. After installing the filter, check that there is no oil leakage
while the engine is running.
5. Recheck the oil level using the dipstick.
(Refer to page D-7.)