ignition MAZDA PROTEGE 1992 Workshop Manual

F CONTROL SYSTEM
Ve: Battery voltage
erminal Input Output
Connection to Test condition Correct voltage Remark
3u 0 Injector (Nos. 1, 3) Ignition switch ON VB * Engine Signal
Idle Va Monitor: Green
and red lamps
Engine speed above 2,000 rpm on de- Va
flash
celeration (After warm-up)
3v 0 Injector (Nos. 2, 4) ignition switch at idle
VB
Idle VB
Engine speed above 2,000 rpm on de-
VB
celeration (After warm-up)
3W 0 1-2 shift solenoid Solenoid valve ON i&I AT running
valve
Solenoid valve OFF ov
3x 0 2-3 shift solenoid Solenoid valve ON
VB AT running
valve
Solenoid valve OFF ov
3Y 0
ZH;hift solenoid Solenoid valve ON VB AT running
Solenoid valve OFF ov
32 0 Lockup solenoid Solenoid valve ON
VB AT running
valve
Solenoid valve OFF ov
23UOFX-1~
1 I u- l-1 ,
III h-3
I r
3y 13W 13U (3Sl3Cj3+4]3K 31 13Gj3EI 3C 13A 2012h42Kl21 12Gl2E12Cj2A 1 U 11 SllC$O 1 MI1 K 1 I 11 G 1 El 1 C 11 A
32 )3X I3Vj3Tj3R]3Pj3N]3L 3Jj3Hj3F13D 138 2P)2N)2L~2J~2H~2F~2D~2B 1V IlTjlRjlP 1NjlL 1JjlH 1FI lD\lB
-*’
.J’ -
F-l 66

F CONTROL SYSTEM
23UOFX-15
23UOFX-15
23UOFX-15
LOCK
4
I
13UOFX-oc
F-l 72
6. Turn the ignition switch OFF.
7. Disconnect the negative battery terminal for
at least 20 sec.
to eliminate the malfunction code that was created during
inspection from the control unit memory.
Replacetnent
1. Disconnect the oxygen sensor connector.
2. Remove the oxygen sensor.
3. Install in the reverse order of removal.
Tightening torque:
29-49 N-m (3-5 m-kg, 22-36 ft-lb)
MAIN RELAY (FUEL INJ RELAY)
Inspection
1. Verify that the main relay clicks when turning the ignition
switch ON and OFF.
2. Apply battery voltage to terminal A and ground terminal E3
of the main relay.
3. Check continuity of the terminals as shown.
VB: Battery voltage
Terminals 1 Ve not applied VB applied
C-D No continuity Continuity
4. If not as specified, replace the main relay.
CLUTCH SWITCH (MTX)
Inspection
1, Disconnect the clutch switch connector.
2. Connect an ohmmeter to the switch.
3. Check continuity of the switch.
Pedal Continuity
Depressed Yes
Released No
4. If not as specified, replace the clutch switch. ,
Replacement
1. Disconnect the clutch switch connector.
2. Loosen the locknuts.
3. Remove the clutch switch.
4. Install in the reverse order of removal.
5. Adjust the pedal height. (Refer to page H-6.)

G
ENGINE ELECTRICAL SYSTEM
INDEX ......................................................
OUTLINE ..................................................
SPECIFICATIONS .................................... G- 3
TROUBLESHOOTING
GUIDE.. .................... G-
4
DIAGNOSTIC INDEX ................................
SYMPTOM TROUBLESHOOTING..
............. :- t
-
CHARGING SYSTEM ................................. G- 6
PREPARATION .......................................
CIRCUIT DIAGRAM ................................. :I ;
TROUBLESHOOTING .............................. G- 7
BATTERY ............................................... G- 6
ALTERNATOR ........................................ G-10
DRIVE BELT ........................................... G-14
IGNITION SYSTEM .................................... G-15
PREPARATION ....................................... G-15
CIRCUIT DIAGRAM ................................. G-15
TROUBLESHOOTING .............................. G-16
IGNITION TIMING ................................... G-17
HIGH-TENSION LEAD .............................. G-17
SPARK PLUGS ....................................... G-16
IGNITION COIL ....................................... G-19
DISTRIBUTOR ........................................ G-20
IGNITER ................................................ G-23
STARTING SYSTEM .................................. G-24
PREPARATION ....................................... G-24
CIRCUIT DIAGRAM ................................. G-24
STARTER ...............................................
G-25
STARTER INTERLOCK SWITCH (MTX)
........ G-31
03UOGX-001

G INDEX
NDEX
- 03UOGX-00:
6. Ignition coil 1. Battery
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page G- 8
Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..t page G- 9
2. Alternator
Removal / Installation . . . . . . . . . . . . . . . . . .
page G-l 0
Disassembly / Assembly . . . . . . . . . . . . . page G-l 1
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 2
3. Drive belt
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 4
Adjustment . . . . . . . . page G-l 4
Replacement . . . . . . . . . . . . . .
page G-l 4
4. High-tension lead
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page G-l 7
5. Spark plugs
Removal / Installation . . . . . . . . . . page G-1 0
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-l 8
G-2
Inspection .,.. . . . . . . . . . . . . . . . . I . . . . . page
G-l 9
7. Distributor
Spark test ., . . . . . . . . . . ,... . . . . . . . .
page G,-20
Electronic advance inspection page G-20
Removal / Installation ,................. page G-21
Disassembly / Assembly.. , . . page
G-22
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-22
8. Igniter
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page G-23
9. Starter
Removal / Installation .;...........,.... page G-25
Disassembly ! Assembly . . . . . . . . . . . . . page G-26
Inspection . . . . ...‘........................,,,
page G-28 .--
10. Starter interluck switch
Inspection... . . . . . . . . . . . . . . . . . . . . ,.., ,...,
page G-31

OUTLINE G
OUTLINE
SPECIFICATIONS
Item EnginelTransaxle
‘-2, B6 SOHC BP SOHC BP DOHC
MTX 1 ATX MTX ( ATX
Voltage v 1 12
I
3attery
Dark current*’ Type and capacity
(20-hour rate)
mA 55D23L (60AH) 55D23L (60AH)
Max. 20.0
L\lternator
Starter
Type AC
output V-A 12-65
Regulator type Transistorized (built-in IC regulator)
Regulated voltage V 14.1-14.7
Brush length Standard 21.5 (0.846)
mm (in) Minimum 8.0 (0.315)
Drive belt deflection
New
98 N (10 kg, 22 lb)
mm (in) Used 8-Q (0.31-0.35)
Q-10 (0.35-0.39)
Type
I Direct Direct
I Coaxial
Direct Coaxial
reduction reduction I
output V-kW 12-0.95 12-0.95 12-1.4
12-0.95 12-1.4
Brush length Standard 17 (0.67) 17 (0.67) 17.5 (0.69) 17 (0.67)
17.5 (0.69)
mm (in) Minimum 11.5 (0.453) 11.5 (0.453) 10.0 (0.39) 11.5 (0.453) 10.0 (0.39)
Distributor
Ignition timing BTDC
(TEN terminal of diagnosis connector grounded) Electronic spark advance (photo diode)
6O--8O 4O-6O Q”-1 1 o
Ignition coil
Spark plug Resistance
(at 20% [68OF]) Primary
coil winding 0.81-O.QQg
Secondary
coil winding IO-16 kg
BKR5E-11 BKR5Ell BKR5Ell
NGK
BKR6E-11 BKRGEl 1 BKRGEli
BKR7Ell
Type NIPPON-
DENSON Kl GPR-Ul l
K20PRU 11 KIGPR-Ull
K20PR-Ul l KIGPR-Ull
K20PRUll
K22PR-Ul l
I Plua aao mm (in) I 1.0-l .l (0.039-0.043)
Firing order
’ Dark current is the constant flow of current while the ignition switch is OFF.
(i.e. engine control unit, audio, etc.) l-3-4-2
23lJOGX-00
G-3

TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
DIAGNOSTIC INDEX
No. Troubleshooting items
Page
1
Will not crank-starter motor does not operate G-4
2
Will not crank-starter motor spins G-4
3
Cranks slowly G-5 4
Alternator warning lamp illuminates when engine running
G-5
5 Discharged battery G-5
6
Misfire
G-5
03UOGX-004
SYMPTOM TROUBLESHOOTING -
1
iTEl
1
2
3 Will not crank-Starter motor does not operate
INSPECTION
T
Check if engine cranks with fully charged battery
Check if battery voltage is applied at B terminal
TERMINAL
battery voltaae is aoolied at S terminal
when clutch pedal depressed (MTX) and ignition
switch in START position
S TERMINAL
Yes
No
Yes ACTION Check charging system CT- page G-7
Go to next step
Go to next step
No Check wire harness
Yes
l Check magnetic switch l Check field coil l Check armature
No
l Check starter interlock switch (MTX) ccp: page G-31 l Check inhibitor switch (ATX) c=p Section K l Check ignition switch CI Section T l Check wire harness
1 L-T page G-28
CT- page G-29
CT- page G-29
23UOGX.001
03UOGX-006
G-4

TROUBLESHOOTING GUIDE G
3 Cranks slowly
STEP INSPECTION ACTION
1 Check if engine cranks normally with fully Yes Check charging system CT page G-7
charged battery
No Go to next step
2 Check starter cable connection for looseness Yes Repair or replace connection
and corrosion
OBUOGX-OC
I 1 4
.
Alternator warning lamp illuminates when engine running
STEP INSPECTION ACTION
1 Check for correct battery voltage at idle Yes Check wire harness between alternator L terminal and aI*
Specification: 14.1--14.7V ternator warning lamp
No Check charging system w page G-7
03UOGX-008
5 I Discharged battery I 1TEP INSPECTION
f Check charging system w page G-7 -
6
TEF
1
r
--
Yes
03UOGX-009
ACTION
Turn ignition switch ON and check dark current as shown
Dark current: Below 20mA
No Repair or replace parts as necessary 1
Misfire
INSPECTION
-
Disconnect high-tension lead from each spark
plug and check for strong blue spark while
cranking
, i
Yes
No T-
I
ACTION
- Check spark plug w page G-f8
~3 If OK, engine electrical system normal
~3 If not OK, clean or replace spark plug
Check ignition system ci’ page G-16
1 03UOGX-010
G-5

G CHARGING SYSTEM
03UOGX-011
CIRCUIT DIAGRAM
CHARGING SYSTEM
PREPARATION
SST
I I
49 9200 020
Tension gauge,
V-ribbed belt For
inspection of
drive belt tension
STATOR
1 DIODE TRIO
T l-f-l /
-I J
WARNING
t
I --.- I I I I 15A
e I
I I -L
-E-
I IC REGULATOR
0
-
BATTERY = IGNITION
SWITCH
03u0tix-012
The alternator has a self-diagnostic function to warn of the following
If a problem arises, the alternator warning lamp illuminates. problems in the charging system.
1. S terminal circtiit open
2. No voltage output
3. Field coil circuit open
4. B terminal circuit open
5. Voltage output too high
G-6

IGNITION SYSTEM G
IGNITION SYSTEM
PREPARATION
SST
49 NO18 001
Adapter Harness
CIRCUIT DIAGRAM
ECU
T
IGNITION SWITCH
,
I
DISTRIBUTOR
7
1 ZL BATTERY
IGNITER
03UOGX-03t
G-15

G IGNITION SYSTEM
TROUBLESHOOTING
iTEP
INSPECTION
ACTION
1
Check if MIL illuminates when engine is running Yes Check for malfunction code number
and perform troubleshooting (TEN ter-
minal grounded) c7 Section F
No Go to next step
2 Drsconnect high-tension lead from distributor and
Yes
check for strong blue spark while cranking en-
l Check distributor cap and rotor v page G-22
gine * Check high-tension lead
KP page G-19 c7 page G-17
+ Ignition system normal
No
Go to next step
3 Check if resistance of ignition coil is OK
Yes
Go to next step ~7
page G-19
Specification (at 20°C [66”9):
Primary coil winding: 0.81-0.99Q No
Replace ignition coil
Secondary coil winding: IO-16 kQ
-i
Check if resistance of high-tension leads is OK Yes Go to next step
D= page G-17
Specification: 16 kQ per 1 m (3.28 ft)
No Replace high-tension lead
5 Check if igniter is OK
m- page G-23 Yes
Replace ECU
No
Replace igniter
03UOGX-03
G-16