ignition MITSUBISHI 3000GT 1991 Service Manual

I,
ELECTRONIC CONTROL SUSPENSION (ECS) - ;;~i%:~ustment339-15
Item No.Check
PointCheck ConditionSoundness Determination Value
24
Check by actually operating
vehicle.Speedometer indication and
MUT indication coincide.
26
61
62
63
64Vehicle
speed
sensorstop
lightswitch
F.R.actuator
F.L.actuator
R.R.actuator
R.L.actuatorDepress brake pedal.
ON
Do not depress brake pedal.OFF
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD
Tour mode with vehicle stationarySOFT
Sport mode with vehicle stationaryHARD4. ACTUATOR CHECK
(I) Using the MUT, force-drive the actuator and fix the damping force changeover.
(2) Check service data (Item No. 61 through 64) to verify that the actuator has been force-driven.
NOTE
lAll of the four actuators in the shock absorbers are simultaneously changed over by forced drive.
lThe damping force changed over and fixed by forced drive is cleared by the following three conditions.1. Ignition switch OFF
2. Vehicle speed 3 km/h (1.9 mph) or more
3. MUT disconnected
Actuator Check List
Item No.Check Point
Check ConditionMUT Service Data Item
No. 61 - 64 Indicated
01Damping force SOFT
03Damping force MEDIUM
04Damping force HARD
Vehicle in stationary
conditionSOFT
MEDIUM
HARD
i
TSB Revision

33B-18ELECTRONIC CONTROL SUSPENSION (EC9 - ~::::u:?‘s*men*
\/I
I(Front)(Rear)I
12FOOG
6. ACTUATOR OPERATION CHECKM33FJAA
6-1. Actuator Operating Sound Check
(I) Set the ignition switch to ON.
(2) Bring your ear near the top of the shock absorber.dNOTE
In the case of the rear shock absorbers, remove the trim
cover at the top of the shock absorber before bringing your
ear near the shock absorber.
(3) Check that the operating sound of the actuator in the shockabsorber can be heard each time the control modes are
changed by pressing the ECS switch.
6-2. Damping Force Check(1) Set the ignition switch to ON.
(ECS indicator Tour ON, damping force SOFT)
(2) Check the damping force SOFT state by shaking the top
mounting points of the front shock absorbers or the top ofthe rear end panels of the rear shock absorbers up and
down.
(3) Press the ECS switch to change the control mode to Sport.(ECS indicator Sport ON, damping force HARD)
(4) Shake the vehicle up and down to check that the dampingforce is harder than in the SOFT state.
TSB Revision

ELECTRONIC CONTROL SUSPENSION (ECS) - Circuit Diaaram 33B-23
IGN:sw1::A?-m
I&
177
i '
3
I
2YJ
-+d
T-J
---
ON(IG2)SV
el
ENGINEf"BTROL
GNDIfi
1234
J333256‘78
6461 72>
I
I
CLL2c
I
,Jm4,\/\THROTTLE;;;EI;;ON
4-1
jV
f
. I
!i
ss’
2
___--_--- _-- ------2354 55F
"pLl
cl w&
114 3__------ -------
I
nimCL
IGNITIONSWITCH(IG1)18Bl
NON-TURBO\
G-R
COMBI-
%kiN'(REED>
G SENSOR
lf?EzJi
STEERING
WHEEL ANGLE
SPEED SENSOR
liZI1 2 3aTSB Revision

35-8SERVICE BRAKES -Anti-lock Braking System Troubleshooting
TROUBLESHOOTING (ABS - FWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
(2) With the ignition key in the “START” position,
below up to the time the engine starts?power to the ABS ECU is interrupted and the
(1) When the ignition key is turned to the “ON”ABS warning light remains lit because the valve
position, the ABS ECU causes the ABS warningrelay is OFF.
light to flash twice in about one second (during
(3) When the ignition key is returned from the
which the valve relay self check is made) and“START” position to the “ON” position, the
then causes it to go out.ABS warning light flashes twice in about one
second (during which. the valve relay self check
-is made again) and then goes out.
ABS warning
ONlightII
-I
keyACC,
LO!: +--14A0589
Yes>CONTINUED ON NEXT PAGE
No
”
weenABS warning
1 TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
L’
No.Trouble condition\4
After the ignition key is turned to the
“ON” position, it blinks once and then
illuminates when it is turned to the
“START” position. When the key is
returned to the “ON” position, the light
blinks again. (Blinking with the ignition
key in the “ON” position is synchronized
with operation noise of the valve relay.)
ABSwarninglight
key ACC. L::+
Ignition
14A05931 CONTINUED FROM PREVIOUS PAGE
1Major causes
l Break in harness for ECU warning
light drive circuit
l Malfunction of ECU
Does the ABS warning light illuminate
when starting to drive the car?
iIs there one-sided braking, insufficient
>CONTINUED ON NEXT PAGEI
I
YesTrouble condition
One-sided braking
Insufficient braking force
ABS sometimes functions even when
there is no sudden braking.
(ABSoperation vibration is transmitted.)Remedy
Check, using flow
P.35-19.)Remedy
l Check HU operation and, if
l necessary, replace HU.
If HU is normal, check struc-
l
HydraJicl Malfunction in HU solenoid valvetural parts for normal
braking.
Insufficient wheel speed sensor put voltage (sensor malfunction, too
large a gap between sensor rotor,
l Malfunction of ABS ECU(Refer to
P.35-57.) and, if
necessary, replace sensor,
If tests indicate that there are
no mechanical or electricalfaiIures,replace the ECU.
TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
35-11
Adapter
iarness%f&(MB9913771(Mi3991341)\12FOO57
CHECK USING SELF DIAGNOSIS FUNCTION
(1) With the ignition switch OFF, connect the MUT through the
adapter harness
(MB9913771, turn the ignition ON and
select the ABS system. (The ABS warning light lights up, it
goes into the MUT mode. In the MUT mode, ABS does
not function.)
If it does not go into the MUT mode, check the ECU power
circuit and the harness between the ECU and diagnosis
check terminals.
(2) Read the diagnosis output codes from the ECU memory.
(3) Clear the diagnosis codes once from memory. (Refer to
P.35-12.)If the memory cannot be cleared, the ECU is currently
detecting the trouble and the ABS ECU is in fail safe. If it
can be cleared, the trouble is either temporary or appears
only when driving.
(4) When the trouble codes cannot be cleared, or when the
ABS ECU goes into fail safe during another test drive and
trouble codes are output, check according to trouble code
check charts (E-l-E-6).
DIAGNOSIS CODE CHART
Diagnosis codeCheckReferenceDiagnosis codeCheck
Referencechart namepagechart namepawNo. MUT display lettersor remedyNo. MUT display lettersor remedy
L11FR SNSR. OPEN41FR SOL. VALVE
12FL SNSR. OPEN42FL SOL. VALVEE-4P.35-23E-lP.35-2013RR SNSR. OPEN43REAR SOL. V.
14RL SNSR. OPEN51VALVE RELAYE-5P.35-24
15VEH. SPD. SNSR.E-2P.35-20 52MOTOR RELAYE-6P.35-25
22STOP LAMP SWE-3P.35-2055 CONT. UNITECU-
replacementI
TSB Revision

.SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-13 'A ABS warning light does not light at all.
iJ[Explanation][Hint]
When it does not light up at all, there is a strongIf other warning lights do not light up either, fuse is
possibility that there is trouble with ABS warningprobably blown.
light or with power to the light.
id
r
f%ER RELAY
110
* ::h=g
6
::5
d
.-2=
?Et0
~
2____--..-
?EI
5fir 4
I
4 -
IGNITIONSWITCH(IG2)m!--
mj:
JSIBLE LINK0tiB
2
L__---------___
0
Lp1%
%2
j:(L-R)dg
6-k
&h+&"..L"Ei SOLENOID1:
G-R
G-R
^ -tl- - D
HH H?bb
IN:IGl)-
59
1
ki@iNATION
iB
ABS-ECU
Kxss-AK-RSGOIA
1 TSB RevisionI

SERVICE BRAKES- Anti-lock Braking System Troubleshooting
Yes
Turn the ignition switch OFF and
check.
4- No
Does voltage between
harness connector terminal
No. 14 and ground indicate
battery voltage?combination meter from
fuse No. 11 is broken.
Yes
ylCircuit in combination meter
is broken.
Is there continuity between combination
meter No. 58 and No 59 terminals7
.rT/“I./ Faulty1 +I[&
r,No ,IAre instrument panel wiring harness
and body wiring harness connected
properly?Connect connectors firmly.
(Check for pins pulled out or
bent, and repair as needed.)
Yes
Broken wire in ECU, valve relay or both
drive circuits. Check both circuits.
TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-15
ICheck ABS ECU.Remove the ECU connector and
check.Does the voltage between ECU harness
connector terminal No. 25 and ground
indicate battery voltage while the
ignition key is in the “ON” position?
Yes
b Broken wire between ABS
warning light and ECU) Repair harness.
I ABS ECU malfunctionI) Replace ABS ECU.
Is valve relay normal? (Refer to
P.35-62.)Yes+ Valve relay malfunctionb Replace valve relay.
install the valve relay, remove the HU
connector and check.
IDoes voltage between theINO IHU harness\----+I Broken harness wireII1-1 Repair harness.I
Iconnector terminal No. 8 and ground
indicate battery voltage while the
ignition key is in the “ON” position?between ABS warning
light and HU1IYes
Is there continuity between HU harness
4:~~&?$?%$&ndconnector terminal No. 9 and ground?
Is there continuity between HU harness
connector terminals No. 8 and No.
9?
j HU malfunctionI> Replace HU.
Yes
L Connector not connected
securely., Replace connector.I
TSB Revision

35-16SERVICE BRAKES -Anti-lock Braking System Troubleshooting
BABS warning light stays on when the ignition key is in the “ON” position.
[Explanation]
[Hint]
This is the symptom when the ABS ECU does not
Check the diagnosis output and if there is no output
power up due to broken ECU power circuit, etc.,
voltage or if the MUT and ABS ECU cannot
when the fail safe function operates and isolates thecommunicate, there is a good possibility that power
system or when the warning light drive circuit is
is not flowing to the ECU.
short circuited.
!8IGNIISWIT(-
:Et
J’B @
C151
:
E
COMBINATION
METER
-19
7
------____-_---1
2
610 2
~;@lizEFgIIc,
6227J
r bL-1
IN(IGl)
1
,
ig
)
158
7
r-TSB iCaution
lIf the trouble code is output, the system can
be in the fail safe mode. in such a case, erase
the trouble code and then restart the engine
to check if the system is currently in a fault
condition.
~~~~
~~~~1
I,No ,I
Yes6
Replace ECU.
41,No rIDoes the ABS warning light
remain illuminated even with
the HU connector discon-
nected?
Yes
Short-circuit in harness
between HU or ECU and ABS
warning light
> Repair harness or replace
combination meter.
bvision