ignition MITSUBISHI 3000GT 1991 Service Manual

SERVICE BRAKES -Anti-lock Braking System Troubleshooting3547CONTINUED FROM
PREVIOUS PAGE
ABS
POSER
RELAY
DIODE
SELF-LM&OS'S
CONNECTOR
FRONT
SIDEYes
Is power relay normal?
(Refer to
P.35-62.)
-Replace power relay.
With the ignition key in the
“ON” position, does voltage
between ECU connector
terminal No. 18 and ground
indicate the battery voltage?
I
1YesNo
-
I--Harness wire between
power relay and ECU
is brokenJ1Repair harness.
I
~ No
Is there continuity betweenrbody harness connector ter-agnosis inspection ter-
minals No. 23 and No. 24,minal and ABS ECU is
and diagnosis inspection ter-
minals No. 4 & No. 1 O?Yes
”Malfunction of ABS ECUReplace ABS ECU.
TSB Revision

35-18SERVICE BRAKES -Anti-lock Braking System Troubleshooting
CABS warning light does not illuminate when the ignition key is in the “START” position.
[Explanation]
LJThe ABS ECU uses the
IG2 power source which is
turned off in the “START” position. The ABS
warning light uses the
IG, power source which is
not turned off even in the “START” position.
Consequently, in the “START” position, power is offand the ECU turns the valve relay OFF. If the
warning light does not illuminate at this time, there
is trouble in the warning light circuit on the valve
relay side.
J’B 6
[15
Pi9
I58
:127r',L
ALI
Y-3>
B -
::9
IG-R l,,l G-6
7
COMBINATION
METER
.- ------ ---_-__1
‘$2 1274
7
sE,
85
ON(IGl)
1
;ABS
ECU
H
(--)With the ignition key in the
indicate the battery voltage?
Yes
Yes
I
Yes*Replace valve relay.
HU harness malfunction
NOTEWhen performing the check marked *, note polarity of the diode
(refer to the circuit diagram).
vision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-19
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
(L.-Jilluminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
When power flows, the ABS ECU turns on theharness between the ECU and the warning light, the
warning light for approximately 1 sec. while itlight illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in thethe valve relay test, etc.
IGNITIONSWITCH(IG1)
I
COMBINATION
METER
58
g:"I 2
3
mi
456788 7
ASS-ECUIn the ignition key “ON”
position, does voltage
between terminal No. 25 andground indicate battery
voltage?ABS warning light andECUis broken.
Yes
Repair harness.
vMalfunction of ABS ECU
+ Replace ABS ECU.
TSB Revision

35-20SERVICE BRAKES -Anti-lock Braking System Troubleshooting
the following diagnosis codes are displayed “11 FR SNSR. OPEN”
“12 FL SNSR. OPEN” “13 RR SNSR. OPEN” “14 RL SNSR. OPEN”
[Explanation]
The ABS ECU detects breaks in the wheel speed
sensor wire. This trouble code is output if the wheel
speed sensor signal is not input (or short circuited)
or if its output is low when starting to drive or while
driving.[Hint]
In addition to a broken wire/short circuit in the wheel
speed sensor, also check whether the sensor gap is
too large, sensor harness wire is broken, or sensor
harness and body connector are not properly
con-
netted.
r--~- -E-2 When dlagnosls code“15 VEH. SPD. SNSR.” is displayedI[Explanation]
This trouble code is output when there is an
abnormality (other than broken wire or short circuit)
in any of the wheel speed sensor output signals
while driving.
[Hint]
The following can be considered as the cause of the
wheel speed sensor output abnormality.
l Distortion of rotor, teeth missing
lLow frequency noise interference when sensor
harness wire is broken
l Noise interference in sensor signal
lSensor output signal is below the standard value
or amplitude modulation is over the standard
value. Using an oscilloscope to measure the
wave shape of the wheel speed sensor output
signal is very effective.l Broken sensor harness
l Poor connection of connector
NOTE(1) If contact is poor, check the sensor cable by
bending and lightly stretching it.
(2) Except for the case where a fault condition
exists in the system, but the inspection results
are normal; if an abnormality cannot be found in
the sensor circuit displayed as abnormal, erase
the diagnosis code and turn the ignition switch
to OFF once, and then test-drive again.
If the same trouble code is output, replace the
ABS ECU. If the trouble does not occur
any-more, the problem is likely to be with the ABS
ECU.(If the trouble is in the speed sensor circuit, but
is difficult to recreate, it will recur even after the
ABS ECU has been replaced.)
SPEED SENSOR
FRONTCLH) FRONTFTRH)RF.AR(LH) REfIR(RH)
@cTJ @ij@ fi&
1 TSB Revision

35-24SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-5When diagnosis code “51 VALVE RELAY” is displayed
[Explanation]
When the ignition switch is turned ON, the ABS
ECU switches the valve relay OFF and ON for an
initial check, compares the voltage of the signal to
the valve relay and valve power monitor line voltage
to check whether the valve relay operation isnormal. In addition, normally it monitors whether or
not there is power in the valve power monitor line
since the valve relay is normally ON. Then, if the
supply of power to the valve power monitor line is
interrupted, this trouble code will be output.
EPfiiB EenIGNITIONSWITCH(IG1)
COMSINATIONm
I
H” g@J$s2
4:u
,,8I. -----I/IL’ /
IIII
I /IIII/I/-,----__--_,>yo “-a-‘+G ------------------ ?$”:
;’m[1?610 2pEl%zq~,___ ____________~_______~~~~
>;?
$-:dL1:27 =Yi62.G 22 +%!
i.-I
1/2131a)5161718(QIIO(I ~~~2(13~~a~i5~~6/i7~~~IQ$O~Y~2~3~24~~6~~~28~~~1~2~3~4~5~Remove and check the valve relay.
IWhen the valve relay is checked, are
the following conditions found?
No. 85
-No. 86: Resistance
value 60 - 120 fiNo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When battery voltage is applied
between terminals No. 86 and No. 85.
No. 30
- No. 87: Continuity
No. 30 - No. 87a: No continuity
Yes
Install the valve relay and remove
the HU connector.
E+GG-pqReplace valve relay.
&I/ NnIIWith the ignition key “ON”, does the
Is there continuity between HU No. 8
and No. 7 terminals?
IYes
Connect the HU harness and remove
the ECU connector.Faulty harness in HU
1Does resistance between body con-
nector terminal No. 2 and terminal
No. 27 indicate 60
- 120 II
NoMalfunction of harness
between HU and ECU.
Yes
With the ignition key “ON”, does the
voltage between terminal No. 22 and
ground indicate battery voltage?
YesNo
II- Malfunction of harness
between HU and ABS
ECU.Repair harness.
vision

35-26SERVICE BRAKES -Anti-lock Braking System TroubleshootingI
TROUBLESHOOTING (ABS - AWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
below up to the time the engine starts?(2) With the ignition key in the “START” position,
(1) When the ignition key is turned to the “ON”power to the ABS ECU is interrupted and the
position, the ABS ECU causes the ABS warningABS warning light remains lit because the valve
relay is OFF.
light to flash four times in about one second (3) When the ignition key is returned from the
(during which the valve relay self check is made)
and then causes it to go out.“START” position to the “ON” position, the
ABS warning light flashes four times in about
one second (during which the valve relay self
-check is made again) and then goes out.
III
OFFu--I-II
ST
ONACC, LOCK
114A0594Yes
>CONTINUED ON NEXT PAGE
No
No.
Trouble condition
Major causesRemedy
1ABS warning light does not light up at all.l ABS warning light bulb is burnt out.
ACC,LOb--
l Open in ABS warning light electricalCheck, using flowchart A (Refer to
ABScircuit (check for blown fuse)P.35-31.)warningOFFlight
lgmtlon
key
14AO590
2When the ignition key is turned to the
“ON” position, it remains lighted.l Fail safe is functioning due to ECU
self diagnosis.Check, using flowchart B (Refer toABS,“,F
J-l Short in ECU warning light drive circuitP.35-34.)warningl Malfunction of ECUlight
Ignition
key.;i,LOi h
3Does not illuminate when ignition key is
in “START” position.l Malfunction of valve relayl Break in harness between ABS warningCheck, using flowchart C (Refer to
light and HUP.35-36.)l Break in harness between HU andwarning
body ground
TSB Revision1

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-27
i-,’
No.
4Trouble condition
IMajor causes
After the ignition key is turned to the
“ON” position, it blinks once and then
illuminates when it is turned to the
“START” position. When the key is
returned to the “ON” position, the light
blinks again. (Blinking with the ignition
key in the “ON” position is synchronized
with operation noise of the valve relay.)
ABSwarrmglightkey ACC.
LOi;+lgmtion14A0593l Break in harness for ECU warning
light drive circuit
l Malfunction of ECU
CONTINUED FROM PREVIOUS PAGE
Yes
Trouble condition
One-sided braking
Insufficient braking force
Decline in ABS function
ABS sometimes functions even when
there is no sudden braking.
(ABSoperation vibration is transmitted.)Remedy
Check, using flow
chart D (Refer to
P.35-37.)Does the ABS warning light illuminate
when starting to drive the car?Trouble with the motor relay, solenoid
valve [due to self test at start-up or
Is there one-sided braking, insufficient
braking force or malfunction of ABSCONTINUED ON NEXT PAGE
Major causes
l Hydraulic line in HU is clogged.
l Mechanical lock of HU solenoid valve
l Hydraulic line in HU is clogged.
l Malfunction in HU solenoid valve
operation
l Insufficient wheel speed sensor out-
put voltage (sensor malfunction, too
large a gap between sensor rotor,
missing rotor teeth)
l Malfunction of ABS ECURemedy
Check HU operation and, if
necessary, replace
HU.If HU is normal, check struc-
tural parts for normal
braking.
Check wheel speed sensor
(Refer to
P.35-57.) and, if
necessary, replace sensor,
adjust gap or replace rotor.
If tests indicate that there are
no mechanical or electrical
failures,replace the ECU.
TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
MUT
I/(MB991 341)
\03A0211
DIAGNOSIS CODE CHART
I I21G SNSR.IE-3
[ 22 1 STOP LAMPSW 1E-4
CHECK USING SELF DIAGNOSIS FUNCTION
(1) With the ignition switch OFF, connect the MUT through the
adapter harness (MB991377). turn the ignition ON and
select the ABS system. (The ABS warning light lights up, it
goes into the MUT mode. In the MUT mode, ABS does
not function.)
If it does not go into the MUT mode, check the ECU power
circuit and the harness between the ECU and diagnosis
check terminals.
(2) Read the diagnosis output codes from the ECU memory.
(3) Clear the diagnosis codes once from memory. (Refer to
P.35-30.)If the memory cannot be cleared, the ECU is currently
detecting the trouble and the ABS ECU is in fail safe. If it
can be cleared, the trouble is either temporary or appears
only when driving.
(4) When the trouble codes cannot be cleared, or when the
ABS ECU goes into fail safe during another test drive and
trouble codes are output, check according to trouble code
check charts (E-l-E-7).
Reference
we -1 ;+EiT;
I I41FR SOL. VALVEI
P.35-381 ;; / ;;tS;L;;;E/ E-5
I I51VALVE RELAY
P.35-38 1 52 1 MOTOR RELAY)E-7
si 55 / ‘ONT. UNlT/ replaEcCeUment
Reference
iwe
P.35-42
P.35-43
P.35-44
-
1 TSB RtivisionI

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-31
L’A ABS warning light does not light at all.
[Explanation][Hint]
When it does not light up at all, there is a strongIf other warning lights do not light up either, fuse is
possibility that there is trouble with ABS warningprobably blown.
light or with power to the light.
FUSIBLE LINEI
L--L5--
i
IGNITIONSWITCH(IG2)IGNITIONSWITCH(IG1)
(L-R)-' .3
G-RI
7
!
m59COMBINATION
iMETER
1:I1o‘r_- ----- ‘2 -- ‘Ti----‘%--‘79 -_----- -7 -- “j-+3 -----1
=p!Rq3;
g:W
25
b
ABS-ECU
n=
1 TSB Revision

35-32SERVICE BRAKES -AniLlock Braking System Troubleshooting
NoWith the ignition key in the “ON” posi-
I--Check fuse No. 11. If it is
blown, correct the cause of
the blown fuse and then
replace the fuse.J
Yes
I
( ~;T&$Efg,?~ )harness connector terminal
No. 59 and ground indicate
battery voltage?
----F--
&Repair harness.
Circuit in combination meter
-is broken.
Is there continuity between combination
meter No. 58 and No. 59 terminals?
Are instrument panel wiring harness
and body wiring harness connected
Broken wire in ECU, valve relay or both
drive circuits. Check both circuits.
TSB Revision