sensor MITSUBISHI 3000GT 1991 Service Manual

INTAKE AND EXHAUST -Exhaust Pipe, Main Muffler and Catalytic Converter 15-31
- EXHAUST PIPE, MAIN MUFFLER AND CATALYTIC CONVERTER
MlSRA-S
ii REMOVAL AND INSTALLATION31
/
L
LRemoval steps
36ft.lbs.
22013 Nm9 ft.lbs.----
em
/---------6_ 5ftJbs.13 Nm
9 ft.lbs.
1. Main muffler and center
exhaust pipe installation
bolts
2. Protector
l +3. Connection of cable assemblya*4. Rubber hangersa*5. Rubber hangersl *6. Main muffler
7. Gasket8. Mouldings
9. Hanger brackets10. Catalytic converter and center
exhaust pipe installation nuts
11. Hanger bracket
12. Rubber hangers13 Nm
9
ft.lbs.
13. Center exhaust pipe14.Gasket15.Rubber hangers
16.Hanger brackets17.Hanger bracket
18. Rear floor heat
protector
19. Catalytic converter and front
exhaust pipe installation bolts
20.Catalytic converter21.Gasket22.Self-locking nuts23.Rubber hanger
24. Front exhaust pipem
-.Ibs.
25.Gaskets
26.Self-locking nuts
27. Catalytic converter (Right)28.Gasket
29.Hanger bracket
+*l 4130.Oxygen sensor connection31. Heat protector D
32. EGR pipe connection
33.Gasket34. Catalytic converter (Left)
35. Heat protector E
36. Gasket
37. Front floor heat protectorTSB Revision

15-32 INTAKE AND EXHAUST -Exhaust Pipe, Main Muffler and Catalytic Converter
SERVICE POINTS OF REMOVALMlBRBAA
4. 5. REMOVAL OF RUBBER HANGER / 6. MAIN MUFFLERSupport with a transmission jack, etc.
:iJ ~
30. REMOVAL OF OXYGEN SENSORDisconnect the connector of the oxygen sensor, and install
the special tool to the oxygen sensor.
INSPECTIONMlSRCAN
l Check the mufflers and pipes for corrosion or damage.
l Check the rubber hangers for deterioration or damage.
l Check for gas leakage from mufflers and pipes.
lCheck if the main muffler active exhaust system valve can\\be moved smoothly by hand.
SERVICE POINTS OF-INSTALLATIONMllRDAl
30. INSTALLATION OF OXYGEN SENSORUse the special tool to install the oxygen sensor.
3. INSTALLATION OF CABLE ASSEMBLY
Install with the paint mark facing up and adjust the adjusting
nut to obtain the illustrated dimension.
TSB Revision

17-1
EMISSIONCONTROL
.~
CATALYTIC CONVERTER............................:...Inspection
............................................................Removal and Installation
................................
CONTENTSM17.U. -
CRANKCASE EMISSION CONTROL
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ComponentsLocation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Crankcase Ventilation System Inspection
._..Positive Crankcase Ventilation Valve
. . . . . . . . . . . .
EVAPORATIVE EMISSION CONTROL
SYSTEM................................................................Air Conditioner Switch
....................................Air Flow Sensor, Engine Coolant
Temperature Sensor and Intake Air
Temperature Sensor
........................................Canister
............................................................Components Location
....................................
FuelFiller CapInspection................................OverfillLimiter (Two-way Valve)
....................Purge Control Solenoid Valve
........................Purge Control System Inspection
....................................................Purge Control System Inspection

............................................................Purge Control Valve
........................
PurgePort VacuumCheck................................14
14
14
6
10
10
10
6
10
10
9
7
8
9
9EXHAUST GAS RECIRCULATION
(EGR)
SYSTEM. . . . . ..____._.._........__........_____.........................Air-FuelRatio Control (MPI) System. . . . . . . .
Components Location
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .EGR Control Solenoid Valve
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .EGR System Inspection
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .EGR Temperature Sensor
. . . . . . . .EGR Valve - Non Turbo, Turbo>
EGR Valve Control Vacuum Check
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS................................................General Specifications
....................................Service Specifications
....................................
TROUBLESHOOTING. . . . . . . . . . . . . . . . . ..______...............
VACUUM HOSES................................................Inspection
............................................................Installation
........................................................VacuumHosesRouting
....................................
11
14
11
13
12
13
13
12
2
2
22

17-2EMISSION CONTROL - Specifications / Troubleshooting
SPECIFICATIONS
GENERAL SPECIFICATIONSMl’ICA- -\
Items
Crankcase emission control systemSpecifications
Closed type with positive crankcase ventilationvalve
Evaporative emission control systemCanister storage type
Canister
Charcoal type
Purge control solenoid valve
ON/OFF solenoid valve
Exhaust emission control system
Exhaust gas recirculation system
EGR valveVacuum-activated diaphragm type
EGR temperature sensor Thermistor type
EGR control solenoid valve - Non Turbo, Turbo>Duty cycle solenoid valve
Catalytic converter
Monolith type
Location
Under floor
Turbocharger outlet (front bank and rear bank,)
and under floor
SERVICE SPECIFICATIONSMl7CB-.
ItemsSpecifications
Purge control solenoid valve coil resistance
036 - 44 [at 20°C (68”F)I\
EGR temperature sensor resistancekfl60 - 83 [at 50°C (I 22”F)]
11 - 14 [at 100°C (212”F)l
EGR control solenoid valve coil resistance1236 - 44 [at 20°C (68”F)lI
TROUBLESHOOTING
Symptom
Engine will not start
or hard to start
Rough idle or engine
stalls
Probable cause
Vacuum hose disconnected or damaged
The EGR valve is not closed
Malfunction of the purge control solenoid valve
The EGR valve is not closed
Vacuum hose disconnected or damaged
Malfunction of the positive crankcase ventilationvalveRemedy
Repair or replace
Repair or replace
Repair or replace
Repair or replace
Repair or replace
Replace
Malfunction of the purge control systemCheck the system; if there is a
problem, check its component parts
Engine hesitates or3oor acceleration
Zxcessive oil:onsumptron
Malfunction of the exhaust gas recirculation
system
Positive crankcase ventilation line cloggedCheck the system; if there is a
problem, check its component parts
Check positive crankcase
ventila-tion system
Ioor fuel mileageMalfunction of the exhaust gas recirculation
systemTSB RevisionCheck the system; if there is a
problem, check its component parts
d

EMISSION CONTROL - Evaporative Emission Control System17-7
PURGE CONTROL SYSTEM INSPECTION M17lBBP
Barometric pressure sensor
Engine control unit
7EM0161I-----I
\7EM0140t
(1) Disconnect the vacuum hose (red stripes) from the throttle
body,and connect it to a hand vacuum pump.
(2) Plug the nipple from which the vacuum hose is discon-
nected.
(3) Under the engine conditions shown below, check by
applying vacuum from a hand vacuum pump.
When engine is cold
-engine coolant temperature:
60°C (140°F) or less
When engine is hot
-engine coolant temperature:
70°C (158°F) or higher
Engine operatingcondttionApplying vacuumResult
ldllng375 mmHg(14.8 In.Hg)Vacuum is maintalned
I
after staitingengineNOTEThe vacuum will leak con-tenuously if the altitudeis 2,200 m (7.200 ft.) or
higher, or the intake airtemperature is 50°C(I 22°F) or higher.TSB Revision

17-8EMISSION CONTROL - Evaporative Emission Control System
PURGE CONTROL SYSTEM INSPECTION M17IBBQ
Canister
Purge control
valve\
PI IrnQ rnntrnlI.1 I
kXffo~~~~r~~ ’ I I-J
relay
Barometric pressure sensor
Intake air temperature sensor
Engine coolant temperature sensor
II1 I IAir flow sensor
Engine control unit
6EM0215(1) Disconnect the purge air hose from the air intake hose, and
plug the air intake hose. Then, connect the hand vacuum
pump to the purge air hose.
(2) Under the engine conditions shown below, check by
applying vacuum from a hand vacuum pump.
When engine is cold
-engine coolant temperature:
60°C (140°F) or less
Engine operating
conditionApplying vacuumResult
Idling
375 mmHgVacuum is maintained
3,000 rpm(14.8 in.Hg)When engine is hot
-engine coolant temperature:
70°C (158°F) or higher
Engine operating
condition
Idling
3,000 rpm within
three minutes after
starting engine
3,000 rpm after
three minutes
have elapsedafter startingengine
Applying vacuum
375
mmHg(14.8 in.Hg)
Try applyingvacuum
375
mmHg(14.8 in.Hg)
Result
Vacuum is marntained
Vacuum leaks
Vacuum WIII be main-tained momentarily, after
which it will leak.
NOTEThe vacuum WIII leak con-
tinuously if the altitude
is 2,200 m
(7,200 ft.) orhrgher. or the Intake arrtemperature is 50°C(122°F) or higher.
1 TSB Revision

17-10EMISSION CONTROL - Evaporative Emission Control System
I-6EM13i(4) Apply a vacuum and check for airtightness when voltage
applied directly to the purge control solenoid valve and
when the voltage is discontinued.
Battery voltageResultNon-Turbo When applied
Vacuum leaks
When discontinuedVacuum is maintained
TurboWhen applied
When discontinued
Vacuum is maintained
Vacuum leaks
(5) Measure the resistance between the terminals of the
solenoid valve.
Standard value: 36
- 44 R [at 20°C (68”F)]
AIR FLOW SENSOR, ENGINE COOLANT TEMPER-ATURE SENSOR AND INTAKE AIR TEMPERA-
TURE SENSORM17lBGFTo inspect these parts, refer to GROUP 13
- MPI System
Components.
AIR CONDITIONER SWITCHMl7IBHF
To inspect the air conditioner switch, refer to GROUP 55
- Air
Conditioner Switch.
OVERFILL LIMITER (TWO-WAY VALVE)M17IBEFTo inspect the overfill limiter (two-way valve), refer to GROUP
13
- Fuel Tank.
CANISTERM17lBIFTo inspect the canister, refer to GROUP 13
- Fuel Line and
Vapor Line.
FUEL FILLER CAP INSPECTIONM17IBJBCheck the gasket of the fuel filler cap, and the filler cap itself,
for damage or deformation; replace the cap if necessary.
TSB Revision

EMISSION CONTROL -Exhaust Gas Recirculation (EGR) System17-11
EXHAUST GAS RECIRCULATION (EGR) SYSTEMrm?MA- -COMPONENTS LOCATION
L
,
i
-
\\
(%vTT
I
4/ -I---Id/- -3Th
--02
I
1-a\\
IJ-l f--An7FUlOl
NameSymbol
~ EGR control solenoidvalve1 :
EGR temperature sensor ~
EGR valve
7EM014f
1TSB Revision

EMISSION CONTROL - Exhaust Gas Recirculation IEGR) Svstem17-13
GM159
QQQQQQ7FMnn4EGR VALVE - Non Turbo, Turbo>
M17lCKJ
INSPECTION(1) Remove the EGR valve and check it for sticking, deposit of
carbon, etc.
If such condition exists, clean with adequate solvent to
ensure tight valve seat contact.
(2) Connect a hand vacuum pump to the EGR valve.
(3) Apply a vacuum of 500 mmHg (19.8 in.Hg.) and check
airtightness.
(4) Blow in air from one passage of the EGR to check condition
as follows.
INSTALLATIONInstall a new gasket and EGR valve, tighten bolts to specified
torque.
Specified tightening torque: 19
.Nm (13 ft.lbs.)
EGR TEMPERATURE SENSOR M17lCYC
INSPECTION(1) Remove the EGR temperature sensor.
(2) Place the EGR temperature sensor in water, and then
measure the resistance value between terminals 1 and 2
while increasing the water’s temperature.
Replace the EGR temperature sensor if there is a significant
deviation from the standard value.
INSTALLATIONInstall the EGR temperature sensor tighten to specified torque.
Specified tightening torque: 11 Nm (8
ftlbs.)
EGR CONTROL SOLENOID VALVE Non Turbo, Turbo>MlllCRE
INSPECTION
NOTEWhen disconnecting the vacuum hose, make an identification
mark on it so that it can be reconnected to the original position.
(1) Disconnect the vacuum hose (yellow and green stripe) from
the solenoid valve.
(2) Disconnect the harness connector.
(3) Connect a hand vacuum pump to the nipple to which the
green-striped vacuum hose was connected.
1 TSB RevisionI

22-1
iv,MANUAL ~
TRANSAXLE
~
I
CONTENTSM22AA. -
MANUAL TRANSAXLE . . . . . . . . . . . .._...48INPUT SHAFT ASSEMBLY_..________.............: . . . . . . . . . . . . . . . . . . . . . . . . . .30
GENERAL INFORMATION....................................................48
SERVICE ADJUSTMENT PROCEDURES
............................51
Drive Shaft OilSealsReplacement....................................
52Speedometer Cable Replacement....................................
53Transfer Oil Seal Replacement............................................53Transmission Oil Level Inspection....................................51Transmission Oil Replacement............................................51
SHIFT LEVER ASSEMBLY....................................................
53
SPECIAL TOOLS........................................................................50
SPECIFICATIONS
....................................................................49
General Specifications........................................................49Lubricants............................................................................49
TRANSAXLE ASSEMBLY....................................................56,60
TRANSAXLE CONTROL*........................................................54
TRANSFER ASSEMBLY
........................................................59
MANUAL TRANSAXLE ....................2
CLUTCH HOUSING ASSEMBLY............................................46
DIFFERENTIAL ASSEMBLY
....................................................43
5TH SPEED SYNCHRONIZER ASSEMBLY
........................28
GENERAL INFORMATION
....................................................2INTERMEDIATE GEAR ASSEMBLY
....................................
OUTPUT SHAFT ASSEMBLY................................................
SERVICE ADJUSTMENT PROCEDURES............................
Drive Shaft Oil Seals Replacement....................................Speedometer CableReplacement....................................Transmission Oil Level Inspection....................................Transmisston Oil Replacement............................................
SHIFT LEVER ASSEMBLY....................................................
SHIFT RAILS AND FORKS....................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................
Lubricants............................................................................
Sealants and Adhesives........................................................Service Specifications........................................................
Snap Ring (for Adjustment) and Spacer............................
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................
TRANSAXLE ASSEMBLY _____...._........__....................................
TRANSAXLE CONTROL*. . ..________.___.._ ..__._.__.__...............
36
41
9
10
9
9
9
13
42
6
3z
63
3
45
14
11TROUBLESHOOTING
___.._______._____.......,..................................8
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the
SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.