rear MITSUBISHI LANCER 2005 Workshop Manual

REAR FOG LAMP
CHASSIS ELECTRICAL54A-75
FRONT FOG LAMP RELAY CHECK
REAR FOG LAMP
TROUBLESHOOTINGM1542000701300
If the rear fog lamp switch is turned ON when the
headlamp or the front fog lamp is turned ON, the rear
fog lamp is switched ON and OFF alternatively.
If the headlamp and the front fog lamp, the rear fog
lamp is turned OFF at the same time.The fog lamps are controlled by the Smart Wiring
System (SWS). For Troubleshooting, refer to
respective Groups below.
•Not using SWS monitor: GROUP 54B, SWS
Troubleshooting P.54B-38.
•Using SWS monitor: GROUP 54C, SWS
Troubleshooting P.54C-22.
SPECIAL TOOLM1542000600902
1 4
3 2
AC305276
AB
Front fog lamp relay
Battery voltage Tester
connectionSpecified
condition
Not supplied 1 − 4 Open circuit
•Connect
terminal 2 to
the positive
battery terminal
•Connect
terminal 3 to
the negative
battery terminal1 − 4 Less than 2
ohms
Tool Number Name Use
MB990784 Ornament remover Removal of instrument panel
ornament
MB990784

REAR FOG LAMP
CHASSIS ELECTRICAL54A-76
REAR FOG LAMP
REMOVAL AND INSTALLATIONM1542009800077
REAR FOG LAMP SWITCH
REMOVAL AND INSTALATIONM1542014200015
Refer to P.54A-74.
INSPECTIONM1542011200942
REAR FOG LAMP SWITCH CONTINUITY
CHECK
AC305278AB
32
1
4
5
Removal steps
1. Bracket
2. Rear fog lamp assembly
3. Bezel4. Socket
5. BulbRemoval steps (Continued)
AC305187
AB
Switch position Tester
connectionSpecified
condition
Pressed 5 − 6 Less than 2
ohms
Released 5 − 6 Open circuit

SIDE TURN-SIGNAL LAMP
CHASSIS ELECTRICAL54A-77
FRONT FOG LAMP RELAY CHECK
SIDE TURN-SIGNAL LAMP
SPECIAL TOOLM1542000600913
SIDE TURN-SIGNAL LAMP
REMOVAL AND INSTALLATIONM1542003300159
REMOVAL SERVICE POINT
Use a special tool ornament remover (MB990784),
etc. to remove the side turn signal lamp by pushing
the fender forward, bending the hook, and then
unclamping the thumb.
AC305279
1 4
3
2
AB
Rear fog lamp relay
Battery voltage Tester
connectionSpecified
condition
Not supplied 1 − 4 Open circuit
•Connect
terminal 3 to
the positive
battery terminal
•Connect
terminal 2 to
the negative
battery terminal1 − 4 Less than 2
ohms
Tool Number Name Use
MB990784 Ornament remover Removal of side turn-signal lamp
MB990784
AC005718
Side turn signal lamps
MB990784
: Front of vehicle
AC

REAR COMBINATION LAMP
CHASSIS ELECTRICAL54A-79
REAR COMBINATION LAMP
TROUBLESHOOTINGM1542000701322
The lamps setup on the rear combination lamp is
controlled in the same manner as the lamps of the
headlamp assembly. For details go to the reference.
For troubleshooting, refer to respective Groups
below.•Not using SWS monitor: GROUP 54B, SWS
Troubleshooting P.54B-38.
•Using SWS monitor: GROUP 54C, SWS
Troubleshooting P.54C-22.
SPECIAL TOOLM1542000600924
REAR COMBINATION LAMP
REMOVAL AND INSTALLATIONM1542003900441

Tool Number Name Use
MB990784 Ornament remover Removal of rear combination
lamp assembly
MB990784
AC304667
4.9 ± 0.7 N·m
AB
3
4
2
1
Removal steps
1. Rear combination lamp assembly
2. Rear combination lamp body3. Socket assembly
4. BulbRemoval steps (Continued)

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-80

HIGH-MOUNTED STOP LAMP
ON-VEHICLE SERVICE
HIGH-MOUNTED STOP LAMP BULB
REPLACEMENT
M1542014600013
CAUTION
Do not touch bulb surface bare-handed or with
dirty gloves. If dirt is attached on glass surface of
the bulb, immediately use alcohol or thinner to
remove dirt, and install the bulb after well dried.Remove socket from trunk compartment, and
replace bulb.
AC304715AB
3
2 14
Removal steps
1. Rear combination lamp assembly
2. Rear combination lamp body3. Socket assembly
4. BulbRemoval steps (Continued)
AC305292AB
High-mounted
stop lamp

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-81
HIGH-MOUNTED STOP LAMP
REMOVAL AND INSTALLATIONM1542005100452

AC305293
AB
2 3 5 6
7 8
4
1
4.9 ± 0.7 N·m

Removal steps
1. Socket assembly
2. Socket
3. Bulb
4. High-mount stop lamp assembly
5. Socket holder 6. High-mounted stop lamp cover
(front)
7. High-mounted stop lamp cover
(rear)
8. High-mounted stop lamp body Removal steps (Continued)

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-82
AC304750AB
12
Removal steps
1. Rear spoiler (Refer to GROUP 51,
Rear spoiler P.51-18.)
<>2. High-mounted stop lamp

HIGH-MOUNTED STOP LAMP
CHASSIS ELECTRICAL54A-83

REMOVAL SERVICE POINT
<> HIGH-MOUNTED STOP LIGHT
REMOVAL
Use the following steps to easily route high-mounted
stop light harness in the event of installation:
CAUTION
Ensure that the string is tightly tied.
1. Tie a string on the high-mounted stop light
harness (at the connector side).
2. Carefully pull out the high-mounted stop light.
AC304722AB
2
1
Removal steps
•Tailgate trim upper (Refer to
GROUP 52A, Tailgate trim
P.52A-19.)
•High-mounted stop lamp connector
connection
•Rear washer hose connection
(Refer to GROUP 51, Rear wiper
and washer P.51-29.)1. Tailgate spoiler (Refer to GROUP
51, Tailgate spoiler P.51-19.)
•Rear washer nozzle (Refer to
GROUP 51, Rear wiper and
washer P.51-29.)
2. High-mounted stop lampRemoval steps (Continued)
AC005190
String
Connector
AC

SPEAKER
CHASSIS ELECTRICAL54A-93
SPEAKER
REMOVAL AND INSTALLATIONM1544002600454
AC305311AB
12
3
4
5
Front speaker removal steps
1. Front door trim (Refer to GROUP
52A, Door trim P.52A-15.)
2. Front speaker
Rear speaker removal
steps
3. Rear speaker garnish
4. Rear speakerRear speaker removal
steps
5. Quarter trim upper (Refer to
GROUP 52A, Trims P.52A-11.)
6. Rear speaker

ANTENNA
CHASSIS ELECTRICAL54A-94
ANTENNA
REMOVAL AND INSTALLATIONM1544002900529

Pre-removal and Post-installation Operation
•Front pillar trim, Rear pillar trim, Centre pillar trim lower,
Centre pillar trim upper (Refer to GROUP 52A − Trims
P.52A-11.)
•Headlining Removal and Installation (Refer to GROUP
52A, Headlining P.52A-21.)
AC305315AB
1
23
1. Roof antenna poleRemoval steps
2. Roof antenna base
•Instrument panel assembly (Refer to
GROUP 52A, Instrument panel assembly
P.52A-2.)
3. Antenna feeder cable