steering MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1166 of 1501
TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
Page 1167 of 1501
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.
Page 1169 of 1501
the facts, allowing the customer to draw their own
conclusions and make an informed decision about how to
proceed.
STEERING AND SUSPENSION
SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER VEHICLE
OPERATION
Steering and suspension are complex systems made up of a
variety of interdependent components. For proper vehicle handling,
ride, and tire wear, a thorough inspection is required whenever
suspension work is being performed.
Conditions listed assume that the problem has been isolated
to the specific component by proper testing procedures.
NOTE: When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check
and adjust alignment as needed. Refer to the OEM
specifications.
CAUTION: DO NOT use ride height altering or load compensating
components, such as variable rate springs and coil over
shocks, on vehicles with height or load sensing
proportioning valve-equipped braking systems, unless
these components are original equipment.
AIR RIDE SUSPENSION
NOTE: Depending on the air suspension design, there are some
aftermarket products available to eliminate the air ride
suspension on certain vehicles. If the system has been
eliminated with one of these products, then no service is
suggested or required.
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
NOTE: This section covers the air spring portion of the
air shock or strut. For damping portion of shock
or strut conditions and procedures, refer to the
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
section.
AIR RIDE SUSPENSION - AIR SHOCK AND AIR STRUT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Inner fabric of air bag
damaged ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Outer covering of air bag
is cracked to the extent
that inner fabric of air
bag is visible ......... 1 ............ Suggest replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRING VALVE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 1186 of 1501
![MITSUBISHI MONTERO 1998 Service Manual POWER STEERING HOSES
POWER STEERING HOSE INSPECTION \
\
\
\
\
\
\](/img/19/57333/w960_57333-1185.png "MITSUBISHI MONTERO 1998 Service Manual POWER STEERING HOSES
POWER STEERING HOSE INSPECTION \
\
\
\
\
\
\")
POWER STEERING HOSES
POWER STEERING HOSE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Blistered ............... B ........... Require replacement.
Blocked ................. A . Require repair or replacement.
Fitting threads damaged . A . Require repair or replacement.
Fitting threads stripped
(threads missing) ...... A ........... Require replacement.
Inner fabric
(webbing) cut .......... A ........... Require replacement.
Leaking ................. A . Require repair or replacement.
Missing ................. C ........... Require replacement.
Outer covering is cracked
to the extent that
the inner fabric of
hose is visible ........ B ........... Require replacement.
Restricted .............. A . Require repair or replacement.
\
\
\
\
\
\
\
POWER STEERING (HYDRAULIC) PUMPS
If diagnosis has determined that complete disassembly is
necessary to determine the extent of the system failure, the
suggestion may be made to rebuild or replace the power steering pump.
Repair or replacement of the following components may be required if
performed as part of a power steering pump overhaul or rebuild service
to meet a minimum rebuild standard.
POWER STEERING (HYDRAULIC) PUMP INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Belt alignment
incorrect .............. B .......... ( 1) Further inspection
required.
Belt cracked ............ 1 ............ Suggest replacement.
Belt frayed ............. 1 ............ Suggest replacement.
Belt missing ............ C ............ Require replacement.
Belt noisy .............. 2 .......... ( 2) Further inspection
required.
Belt plies separated .... A ............ Require replacement.
Page 1189 of 1501
Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Page 1194 of 1501
adjuster bent ......... A ............ (4) Require repair or
replacement of adjuster.
Torsion bar adjuster
seized ................ A .... ( 4) Require repair or replacement
of adjuster.
Torsion bar adjuster
threads damaged ....... A .... ( 4) Require repair or replacement
of part with damaged threads.
Torsion bar adjuster
threads stripped
(threads missing) ..... A ...... Require replacement of part
with stripped threads.
Vehicle suspension height
not within OEM
specifications ........ B ............ Require adjustment or
replacement.
( 1) - If vehicle is within manufacturer's height
specifications, no service is suggested or required.
( 2) - Some manufacturers require replacement under these
conditions.
( 3) - Check vehicle ride height. If ride height is OK, no
service is suggested or required.
( 4) - Only required if ride height needs to be adjusted.
\
\
\
\
\
\
\
STEEL POWER STEERING LINES
CAUTION: When replacing steel power steering lines, be sure to use
a replacement product that meets or exceeds OEM design
specifications.
STEEL POWER STEERING LINE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
bent ................... B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Blocked ................. A .. Require repair or replacement.
Fitting incorrect
(such as compression
fitting) ............... B ............ Require replacement.
Flare type incorrect .... B ........... Required replacement.
Leaking ................. A ........... Require tightening or
replacement.
Line type incorrect ..... B ............ Require replacement.
Page 1195 of 1501
Restricted .............. A ............ Require replacement.
Routed incorrectly ...... B ..... Require routing correction.
Rust-pitted ............ 1 ............ Suggest replacement.
Rust pitted, affecting
structural integrity .. A ............ Require replacement.
\
\
\
\
\
\
\
STEERING ARMS
STEERING ARM INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
bent ................... B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Taper hole elongated .... A ........ ( 1) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Check for damaged stud.
\
\
\
\
\
\
\
STEERING DAMPERS
The following procedures are only required if the vehicle was
originally equipped from the factory with a steering damper. If the
steering damper is an add-on unit, then the unit may be removed
instead of repairing or replacing.
STEERING DAMPER INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part, if available;
otherwise, replace steering
damper.
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
Page 1196 of 1501
replace steering damper.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace steering damper.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace steering
damper.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace steering
damper.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace steering damper.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace steering damper.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
steering damper.
Binding ................. A ............ Require replacement.
Damper body dented ...... A .......... (1) Further inspection
required.
Damper body punctured ... A ............ Require replacement.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
missing ................ 2 ......... ( 2) Suggest replacement
of boot.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Leaking oil, enough for
fluid to be running
down the body .......... A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noise ................... 2 .......... ( 3) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Seized .................. A ............ Require replacement.
( 1) - Require replacement of units where dents restrict damper
Page 1197 of 1501
piston rod movement. If dents don't restrict movement, no
service is suggested or required. Especially critical on
mono-tube dampers.
(2) - This condition can lead to damage of the piston rod,
which, in turn, causes premature piston rod seal wear.
( 3) - If noise is isolated to damper, suggest replacement.
\
\
\
\
\
\
\
STEERING GEARS (EXCEPT RACK AND PINION)
If diagnosis has determined that complete disassembly is
necessary to determine the extent of the system failure, the
suggestion may be made to rebuild or replace the power steering pump.
Repair or replacement of the following components may be required, if
performed as part of a power steering pump overhaul or rebuild service
to meet a minimum rebuild standard.
STEERING GEAR (EXCEPT RACK AND PINION) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A .. Require replacement of broken
part.
Attaching hardware
loose .................. A .. Require repair or replacement
of loose part.
Attaching hardware
missing ................ C ......... Require replacement of
missing part.
Attaching hardware
threads damaged ........ A .. Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A .... Require replacement of part
with stripped threads.
Binding ................. A ... Require repair or replacement
Flex coupler binding .... A ... Require repair or replacement
of coupler.
Flex coupler loose ...... A ... Require repair or replacement
of coupler.
Flex coupler
missing parts .......... A ... Require repair or replacement
of coupler.
Flex coupler
soft/spongy ............ A . Require replacement of coupler.
Flex coupler torn ....... A . Require replacement of coupler.
Fluid contaminated ...... B ........ ( 1) Require flushing and
refilling of the system.
Gasket leaking .......... A ... Require repair or replacement
of gasket.
Housing leaking ......... A ............ Require replacement.
Hydraulic fittings
leaking ................ A ... Require repair or replacement
of fittings.
Inadequate power assist . A .......... ( 2) Further inspection
required.
See note below.
Lash exceeds
manufacturer's
specifications .......... B .. Require repair or replacement.
Seal leaking ............ A ... Require repair or replacement
Page 1198 of 1501
of seal and/or mating part.
Splines damaged ......... A ... Require repair or replacement
of splines.
Splines stripped ........ A . Require replacement of splines.
Steering coupler
shield cracked ......... 2 ............ Suggest replacement.
Steering coupler
shield missing ......... C ............ Require replacement.
Threads damaged ......... A ... Require repair or replacement
of part with damaged threads.
Threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
U-joint binding ......... A ... Require repair or replacement
of joint.
U-joint loose ........... A ... Require repair or replacement
of joint.
Unequal power assist .... A .. Require repair or replacement.
(1) - Determine and correct source of contamination. OEM
specifications must be followed for fluid type.
( 2) - If steering gear is source of inadequate assist, require
repair or replacement.
\
\
\
\
\
\
\
STEERING GEARS - RACK AND PINION
If diagnosis has determined that complete disassembly is
necessary to determine the extent of the system failure, the
suggestion may be made to rebuild or replace the power steering pump.
Repair or replacement of the following components may be required, if
performed as part of a power steering pump overhaul or rebuild service
to meet a minimum rebuild standard.
STEERING GEARS - RACK AND PINION INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ......... Require replacement of
broken part.
Attaching hardware
loose .................. A .. Require repair or replacement
of loose part.
Attaching hardware
missing ................ C ......... Require replacement of
missing part.
Attaching hardware
threads damaged ........ A .. Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A .... Require replacement of part
with stripped threads.
Balance tube blocked .... A .. Require repair or replacement
of balance tube.
Balance tube missing .... C .. Require replacement of balance
tube.
Balance tube restricted . A ... Require repair or replacement
of balance tube.
Bellows boot
clamp missing .......... C ... Require replacement of clamp.
Bellows boot cracked