MITSUBISHI SPYDER 1990 Service Repair Manual

AUTOMATIC TRANSAXLE OVERHAUL Body
Retainer
Check ball
REASSEMBLY
(1) Install regulator valve.Install retainer plate using
7.’
(2) Install torque converter control valve and torq ue converter
clutch valve.
Install dual retainer plate withInstaller/Remover
6.
(3) Install check balls and retainers.
(4) Install thermal valve.
(5) Install separator plate from transfer plate. Install O/D clutch check ball and oil screen.
TSB Revision

AUTOMATIC TRANSAXLE OVERHAUL Body
accumulator plate (2).
Manual
shaft
seal
(7) Slide transaxle range down the manual shaft
(8) Install manual shaft seal.
Install transaxle range screw.. . .
.
detent as shown.

I
(11) Install valve body.
a screwdriver, push guide bracket’ away to park
sprag rollers.
valve body attaching bolts (18).
oil filter.
oil pan.
NOTE
Apply a
inch bead of 18718or equivalent.
TSB Revision

oil pan bolts.
NOTE
Use Loctite or equivalent bolt
233101800~6
DISASSEMBLY
(1)Remove oil pump seal with Seal Remover ,
REASSEMBLY
Install new oil pump seal with
3 and A d a p t e r ( 5 2 )
TSB Revision

AUTOMATIC TRANSAXLE OVERHAUL Oil Pump
DISASSEMBLY
R e m o v e p u m p .
(2) Installer Puller Set on bolts holes.
(3) Strike the weights of the pullers against bolt heads
of the tools to loosen the
in” on shaft
while loosening pump.
,
(4) Remove oil pump.
(5) Remove oil pump gasket.

AUTOMATIC TRANSAXLE OVERHAUL Pump
(6) Remove the oil O-ring.
,
,
(7) Remove the six bolts, and ‘then disassemble the pump
housing and reaction shaft
,
(8). Remove the oil pump outer gear and oil pump in ner gear
from the pump housing. If the “gears are to be reused,
place.
mark on the ‘to’ ensure that the
mounting direction will be correct;’
gears are
installed.
(Use a felt pen or to place
(9) Remove the four seal rings from the reaction sha ft support;
TSB Revision

R E A S S E M B L Y
(1) Install the oil and
to the pump housing.
If reusing the old gears, marks’
that were made
(2) Measure the side between ‘the
gear and oil pump inner If is
than the standard the pump
Standard value: Side
between outer
oilpump inner ,
.
(3) Measure the pump outer gear
and the pump housing pocket. If the
than the standard value, replace oil pump
Standard value:
Clearance
0.045 0.141
(4) Assemble the
a n d t h e n i n s t a l l t h e m w i t h bolts.
.
. ,
(5) Place the four seal rings onto the reaction sha ft support.
TSB Revision

AUTOMATIC TRANSAXLE OVERHAUL Oil Pump
(6) Install the oil pump O-ring.
(7) Install p u m p g a s k e t .
. .
(8) Install oil pump.
(9) Install pump attaching bolts.
,
TSB Revision

AUTOMATIC TRANSAXLE OVERHAUL
Diffe
cove
Differential cover
DISASSEMBLY
Remove oil seal from housing.,
(2) Remove differential cover
(3) Remove differential cover.
(4) Remove differential retainer bolts.
(5) Loosen differential bearingr e t a i n e r w i t h
Walk retainer out of housing using tool.
TSB Revision

AUTOMATIC TRANSAXLE OVERHAUL
Bearing
(6) Remove differential bearing
(7) Remove bolts from extension housing.
(8) Loosen extension housing with Remover
Walk housing out of transaxle case using special to ol.
(9) Remove extension housing.
differential from differential case side
using Puller
four Adapter Blocks
and Adapter
TSB Revision