engine NISSAN NOTE 2016 Service Repair Manual

EM-100
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
12. Install piston and connecting rod assembly to crankshaft.
• Position crankshaft pin corresponding to connecting rod to be installed onto the bottom dead center.
• Apply new engine oil sufficiently to the cylinder bore, piston and crankshaft pin.
• Match the cylinder position with the cyli nder number on connecting rod to install.
• Using Tool (A) or suitable tool, install piston with the front mark on the piston head facing the front of the engine.
CAUTION:
• Do not damage mating surface with connecting rod cap.
• Do not damage the cylinder wall or crankshaft pin.
13. Install connecting rod cap. • Match the stamped cylinder number marks (C) on connectingrod with those on connecting rod cap to install.
14. Inspect outer diameter of connecting rod bolts. Refer to EM-102, "
Inspection".
15. Tighten connecting rod bolt:
a. Apply new engine oil to the threads and seats of connecting rod bolts.
b. Install connecting rod bolts in several steps.
c. Then turn all connecting rod bolts 60 degrees clockwise (angle tightening). CAUTION:
Check and confirm the tight ening angle by using the Tool (A) or protractor. Avoid judgement by
visual inspection without the Tool (A).
• After tightening connecting rod bolt, che ck that crankshaft rotates smoothly.
• Check the connecting rod side clearance. Refer to EM-102, "
Inspection".
16. Install oil pan (upper). Refer to EM-37, "
Removal and Installation (Upper Oil Pan)".
NOTE: Tool number (A) : EM03470000 (J-8037)
PBIC3765E
(A) : Front mark
(B) : Oil hole
(D) : Connecting rod big end grade
PBIC3766E
Step 1 Tighten to
: 27.4 N·m (2.8 kg-m, 20 ft-lb)
Step 2 Completely loosen : 0 N·m (0 kg-m, 0 ft-lb)
Step 3 Tighten to : 19.6 N·m (2.0 kg-m, 14 ft-lb)
Tool number (A) : KV10112100 (BT-8653-A)
PBIC3753E
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER BLOCKEM-101
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
Install the rear oil seal after installing the oil pan (upper).
17. Install rear oil seal. Refer to EM-74, "
REAR OIL SEAL : Removal and Installation".
18. Install flywheel (M/T models) or drive plate (CVT models).
M/T models
• Secure crankshaft with a stopper plate and tighten bolts crosswise over several times.
CVT models
• Secure crankshaft with a stopper plate and tighten bolts crosswise over several times.
CAUTION:
Do not damage or scratch and contact surface for clutch disc of flywheel.
19. Install knock sensor (1).
• Install connectors so that they are positioned toward the rearof the engine.
CAUTION:
• Do not tighten bolt while holding the connector.
• If any impact by dropping is applied to knock sensor,
replace it with a new one.
NOTE:
• Check that there is no foreign material on the cylinder block
mating surface and the back surface of knock sensor.
• Check that knock sensor does not interfere with other parts.
20. Install crankshaft position sensor (POS) (2) and O-ring (1) and then install the crankshaft position sensor cover (3) on the cylin-
der block (4).
• Tighten bolts with sensor inserted completely.
CAUTION:
• Avoid impacts such as a dropping.
• Do not disassemble.
• Keep sensor away from metal particles.
• Do not place the sensor in a location where it is exposedto magnetism.
• Do not reuse O-ring.
21. For the oil level gauge guide (1), secure in position (B) shown to the water inlet clip (A) after inserting to the cylinder block side.
22. Assembly of the remaining components is in the reverse order of disassembly.
Tool number : KV11105210 (J-44716)
Tool number : KV11105210 (J-44716)
: Engine front
: Engine front
PBIC3754E
JPBIA4202ZZ
PBIC3755E
Revision: August 2015
2016 Versa Note

cardiagn.com

CYLINDER BLOCKEM-103
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
• If oil clearance is out of the standard, replace piston and piston pin assembly.
• When replacing piston and piston pin assembly. Refer to
EM-94, "
Disassembly and Assembly".
NOTE:
• Piston is available together with piston pin as assembly.
• Piston pin (piston pin hole) grade is provided only for the parts installed at the factory. For service parts, no
grades can be selected. Only grade “0” is available.
PISTON RING SIDE CLEARANCE
• Measure the side clearance of piston ring and piston ring groove with a suitable tool (A).
• If the measured value exceeds t he limit, replace piston ring, and
measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
• Check that cylinder bore inner diameter is within specification. Refer to “PISTON TO CYLINDER BORE CLEARANCE”.
• Lubricate piston (1) and piston ring (2) with new engine oil and then insert (A) piston ring until mi ddle of cylinder (B) with piston,
and measure piston ring end gap using feeler gauge (C).
• If the measured value exceeds t he limit, replace piston ring, and
measure again. If it still exceeds the limit, replace cylinder block.
CONNECTING ROD BEND AND TORSION
• Check using connecting rod aligner.
• If it exceeds the limit, replace connecting rod assembly.
CONNECTING ROD BIG END DIAMETER
Standard and Limit : Refer to EM-121, "Cylinder
Block".
PBIC3280J
Standard and Limit : Refer to EM-121, "Cylinder
Block".
PBIC3267J
(A) : Bend
(B) : Torsion
(C) : Feeler gauge
Limit : Refer to EM-121, "Cylinder Block".
PBIC3268J
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-104
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
• Install connecting rod cap (1) without connecting rod bearing
installed, and tightening connecting rod cap bolts to the specified
torque. Refer to EM-93, "
Exploded View".
• Measure the inner diameter (B) of connecting rod big end using suitable tool.
• If out of the standard, replace connecting rod assembly.
CONNECTING ROD BUSHING OIL CLEARANCE
Connecting Rod Bushing Inner Diameter
Measure the inner diameter of connecting rod bushing using suitable
tool (A).
Piston Pin Outer Diameter
Measure the outer diameter of piston pin using micrometer (A).
Connecting Rod Bushing Oil Clearance
(Connecting rod bushing oil clearance) = (Connecting rod bus hing inner diameter) – (Piston pin outer diame-
ter)
• If the measured value is out of the standard range, replace connecting rod assembly and/or piston and pis- ton pin assembly.
• If replacing piston and piston pin assembly. Refer to EM-121, "
Cylinder Block".
• If replacing connecting rod assembly. Refer to EM-125, "
Connecting Rod Bearing".
CYLINDER BLOCK TOP SURFACE DISTORTION
• Using a scraper, remove gasket on the cylinder block su rface, and also remove engine oil, scale, carbon, or
other contamination.
CAUTION:
Be careful not to allow gasket particles to enter engine oil or engine coolant passages.
(2) : Connecting rod
(A) : Example
(B) : Measuring direction of inner diameter
Standard : Refer to EM-121, "Cylinder Block".PBIC3269J
Inner diameter
(Standard) : Refer to
EM-121, "Cylinder
Block".
JPBIA0223ZZ
Outer diameter
(Standard) : Refer to
EM-121, "Cylinder
Block".
JPBIA0218ZZ
Oil clearance
(Standard and Limit) : Refer to
EM-121, "Cylinder Block".
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER BLOCKEM-105
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
• Measure the distortion on the cylinder block upper face at different
points in six directions using suitable tool (A / B).
• If it exceeds the limit, replace cylinder block.
MAIN BEARING HOUSING INNER DIAMETER
• Install main bearing cap without main bearings insta lled, and tighten main bearing cap bolts to the specified
torque. Refer to EM-94, "
Disassembly and Assembly".
• Measure the inner diameter of main bearing housing using suitable tool.
• Measure the position shown [5 mm (0.20 in)] backward from main
bearing housing front side in the 2 directions as shown. The
smaller one is the measured value.
• If out of the standard, replace cylinder block and main bearing caps assembly.
NOTE:
Main bearing caps cannot be replaced individually, bec ause they are machined together with cylinder block.
PISTON TO CYLINDER BORE CLEARANCE
Cylinder Bore Inner Diameter
• Using a suitable tool, measure the cylinder bore for wear, out-of-
round and taper at six different points on each cylinder. [(A) and (B)
directions at (C), (D), and (E)] [(A) is in longitudinal direction of
engine]
NOTE:
When determining cylinder bore grade, measure the cylinder bore
(B) direction at (D) position.
• If the measured value exceeds the limit, or if there are scratches and/or seizure on the cylinder inner wall,
replace cylinder block.
NOTE:
Oversize piston is not available. Limit : Refer to
EM-121, "
Cylinder Block".
JPBIA0224ZZ
(1) : Cylinder block
(2) : Main bearing cap
: Engine front
Standard : Refer to EM-121, "Cylinder Block".
PBIC4005E
(f) : 10 mm (0.39 in)
(g) : 60 mm (2.36 in)
(h) : 124 mm (4.88 in)
Standard:
Cylinder bore inner diameter : Refer to EM-121, "
Cylinder Block".
Limit: Out-of-round [Difference between (A) and (B)]
Taper [Difference between (C) and (E)] : Refer to EM-121, "
Cylinder Block".
JPBIA2059ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER BLOCKEM-107
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
• Measure the dimensions at four different points as shown on each
main journal and pin journal using suitable tool.
• Out-of-round is indicated by the difference in dimensions between
(a) and (b) at (c) and (d).
• Taper is indicated by the diff erence in dimension between (c) and
(d) at (a) and (b).
• If the measured value exceeds the limit, correct or replace crankshaft.
• If corrected, measure the bearing oil clearance of the corrected main journal and/or pin journal. Then select main bearing and/or connecting rod bearing. Refer to EM-125, "
Connecting Rod Bearing" and/or EM-124,
"Main Bearing".
CRANKSHAFT RUNOUT
• Place a V-block on a precise flat table to support the journals on both ends of the crankshaft.
• Place a suitable tool (A) straight up on the No. 3 journal.
• While rotating crankshaft, read the movement of the pointer on the
suitable tool. (Total indicator reading)
• If it exceeds the limit, replace crankshaft.
CONNECTING ROD BEARING OIL CLEARANCE
Method by Calculation
• Install connecting rod bearings (2) to connecting rod (3) and con- necting rod cap (1), and tighten connecting rod cap bolts to the
specified torque. Refer to EM-94, "
Disassembly and Assembly".
• Measure the inner diameter of connecting rod bearing using suit- able tool.
(Bearing oil clearance) = (Connecting rod bearing inner diameter)
– (Crankshaft pin journal diameter)
• If clearance exceeds the limit, select proper connecting rod bearing according to connecting rod big end diameter and crankshaft pin journal diameter to obtain specified bearing oil clearance. Refer to EM-125,
"Connecting Rod Bearing".
Method of Using Plastigage
• Remove engine oil and dust on crankshaft pin and the surfaces of each bearing completely.
• Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil
holes.
• Install connecting rod bearings to connecting rod and c ap, and tighten connecting rod cap bolts to the speci-
fied torque. Refer to EM-94, "
Disassembly and Assembly".
CAUTION:
Do not rotate crankshaft. Limit:
Out-of-round [Difference between (a) and (b)]
Taper [Difference between (c) and (d)] : Refer to EM-121, "
Cylinder Block".JPBIA0229ZZ
Standard and Limit : Refer to EM-121, "Cylinder
Block".
PBIC3458J
(A) : Example
(B) : Inner diameter measuring direction
Standard and Limit : Refer to EM-125, "Connecting Rod Bearing".
PBIC3275J
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
• Remove connecting rod cap and bearing, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING OIL CLEARANCE
Method by Calculation
• Install main bearings (3) to cylinder block (1) and main bearing cap(2), and tighten main bearing cap bolts to the specified torque.
Refer to EM-94, "
Disassembly and Assembly".
• Measure the inner diameter (B) of main bearing (3) using suitable tool.
(Bearing oil clearance) = (Main bearing inner diameter) – (Crank-
shaft main journal diameter)
• If clearance exceeds the limit, select proper main bearing according to main bearing inner diameter and
crankshaft main journal diameter to obtain specified bearing oil clearance. Refer to EM-124, "
Main Bearing".
Method of Using Plastigage
• Remove engine oil and dust on crankshaft main journal and the surfaces of each bearing completely.
• Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding oil
holes.
• Install main bearings to cylinder block and main bearing cap, and tighten main bearing cap bolts to the spec- ified torque. Refer to EM-94, "
Disassembly and Assembly".
CAUTION:
Do not rotate crankshaft.
• Remove main bearing cap and bearings, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING CRUSH HEIGHT
PBIC3276J
(A) : Example
(B) : Inner diameter measuring direction
Standard and Limit : Refer to EM-124, "Main Bearing".
PBIC3277J
PBIC3278J
Revision: August 2015 2016 Versa Note

cardiagn.com

HOW TO SELECT PISTON AND BEARINGEM-113
< UNIT DISASSEMBLY AND ASSEMBLY > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
In grinding crankshaft pin to
use undersize bearings, keep the
fillet R (A) [0.8 - 1.2 mm (0.031 - 0.047 in)].
Main BearingINFOID:0000000012431741
HOW TO SELECT MAIN BEARING
When New Cylinder Block and Crankshaft Are Used
1. “Main Bearing Selection Table” rows correspond to main bearing
housing grade on left side of cylinder block.
• If there is a corrected stamp mark (B) on cylinder block, use itas a correct reference.
2. Apply main journal diameter grade stamped on crankshaft front side to column in the “Main Bearing Selection Table”.
3. Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
4. Apply the symbol obtained to the “Main B earing Grade Table” to select main bearing.
NOTE:
Service part is available as a set of both upper and lower.
When Cylinder Block and Crankshaft Are Reused
1. Measure the dimensions of the cylinder block ma in bearing housing inner diameter and crankshaft main
journal diameter individually. Refer to EM-102, "
Inspection".
2. Apply the measured dimension to the “Main Bearing Selection Table”.
3. Read the symbol at the cross point of selected row and column in the “Main Bearing Selection Table”.
4. Apply the symbol obtained to the “Main B earing Grade Table” to select main bearing.
Bearing undersize table:
Refer to EM-125, "
Connecting Rod Bearing".
PBIC3263J
(A) : Basic stamp mark
: Engine front
PBIC3760E
(A) : Main journal diameter grade (No. 1 to 5 from left)
(B) : Crankshaft pin journal diameter grade (No. 1 to 4 from left)
PBIC3757E
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-116
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000012431742
GENERAL SPECIFICATIONS
Va l v e Ti m i n g
Unit: degree
( ): Valve timing control “ON”
Drive BeltINFOID:0000000012431743
DRIVE BELT
Belt Deflection
*: When engine is cold.Engine type
HR16DE
Cylinder arrangement In-line 4
Displacement cm
3 (cu in)1,598 (97.51)
Bore and stro ke mm (in)78.0× 83.6 (3.071 × 3.291)
Valve arrangement DOHC
Firing order 1-3-4-2
Number of piston rings Compression
2
Oil 1
Compression ratio 9.8:1
Compression pressure
kPa (kg/cm
2, psi) / 200 rpm Standard 1,510 (15.4, 219)
Minimum
1,270 (12.95, 184)
Differential limit between cylinders 100 (1.0, 14.5)
Va l v e t i m i n g
: Intake valve
: Exhaust valve
ab c d e f
216 228 11 (
−27)
AT D C 59 (-21)
ABDC -1 (49)
AT D C 37 (-13)
BBDC
JPBIA4228ZZ
Location Deflection adjustment *
Unit: mm (in)
Used belt New belt
Limit After adjusted
Drive belt With A/C
10.0 (0.39) 4.9 - 5.2 (0.19 - 0.20) 4.1 - 4.4 (0.16 - 0.17)
Without A/C 9.1 (0.36)4.3 - 4.7 (0.17 - 0.19) 3.7 - 3.9 (0.146 - 0.154)
Applied pushing force 98.1 N (10.0 kg-f, 22.0 lb-f)
Revision: August 2015 2016 Versa Note

cardiagn.com

SERVICE DATA AND SPECIFICATIONS (SDS)EM-117
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
Belt Tension and Frequency
*: When engine is cold.
Spark PlugINFOID:0000000012431744
SPARK PLUG (PLATINUM-TIPPED TYPE)
*: Always check with the Parts Department for the latest parts information.
Exhaust ManifoldINFOID:0000000012431745
EXHAUST MANIFOLD
Unit: mm (in)
CamshaftINFOID:0000000012431746
CAMSHAFT
Unit: mm (in)
Location
Tension adjustment *
Unit: N (kg-f,
lb-f) Frequency adjustment * Unit: Hz
Used belt New beltUsed belt
New belt
Limit After adjusted Limit After adjusted
Drive belt With A/C
350 (35.7, 78.7)881 - 951
(89.9 - 97.0,
198.0 - 213.8)
1070 - 1138
(109.1 - 116.1, 240.5 - 255.8) 145.5 230.5 - 239.5 254 - 262
Without A/C 876 - 964
(89.4 - 98.3,
196.9 - 216.7)1064 - 1152
(108.5 - 117.5,
239.2 - 259.0)
162 256.5 - 268.5 282.5 - 293.5
Make
NGK
Standard type* PLZKAR6A-11
Gap (nominal) 1.1 mm (0.043 in)
Items Limit
Surface distortion 0.3 (0.012)
ItemsStandardLimit
Camshaft runout [TIR*] 0.02 (0.0008)0.1 (0.0039)
Camshaft cam height “A” Intake
41.705 - 41.895 (1.6419 - 1.6494) 41.505 (1.6341)
Exhaust 40.915 - 41.105 (1.6108 - 1.6183) 40.715 (1.6029)
Camshaft journal outer diameter No. 1
27.935 - 27.955 (1.0998 - 1.1006) —
No. 2, 3, 4, 5 24.950 - 24.970 (0.9822 - 0.9830) —
Camshaft bracket inner diameter No. 1
28.000 - 28.021 (1.1024 - 1.1032) —
No. 2, 3, 4, 5 25.000 - 25.021 (0.9842 - 0.9850) —
SEM671
Revision: August 2015 2016 Versa Note

cardiagn.com