Security control system NISSAN TEANA 2008 Owner's Manual

PCS-108
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
ST/INHI RLYIgnition switch ON Off
At engine cranking INHI → ST
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the
starter control relay is OFFUNKWN
DETENT SWIgnition switch ON Press the selector button with se-
lector lever in P position
 Selector lever in any position oth-
er than POff
Release the selector button with selector lever in P position On
S/L RLY -REQNone of the conditions below are present Off
 Open the driver door after the ignition switch is turned OFF (for a few
seconds)
 Press the push-button ignition switch when the steering lock is activat-
edOn
S/L STATESteering lock is activated LOCK
Steering lock is deactivated UNLOCK
[DTC: B210A] is detected UNKWN
DTRL REQNOTE:
The item is indicated, but not monitored.Off
OIL P SWIgnition switch OFF, ACC or engine running Open
Ignition switch ON Close
HOOD SWClose the hood Off
Open the hood On
HL WASHER REQNot operating Off
Headlamp washer operating On
THFT HRN REQNot operating Off
Horn is activated with vehicle security (theft warning) system On
HORN CHIRPNot operating Off
 Door locking with Intelligent Key (horn chirp mode)
 Door locking with key fob (horn chirp mode)On
CRNRNG LMP REQNOTE:
The item is indicated, but not monitored.Off Monitor Item Condition Value/Status

PCS-122
< SYMPTOM DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
POWER DISTRIBUTION SYSTEM
SYMPTOM DIAGNOSIS
POWER DISTRIBUTION SYSTEM
Symptom TableINFOID:0000000003805778
The engine start function, door lock function, power distribution system and NATS-IVIS/NVIS in the Intelligent
Key system are closely related to each other regarding control. Narrow down the functional area in question
by checking the following table to identify which function is malfunctioning. The vehicle security function can
operate only when the door lock and power distribution system are operating normally. Therefore, it is easy to
identify any factor unique to the vehicle security system by checking the following table.
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion.
NOTE:
Before starting vehicle security system operation check, the following conditions must be met.
 Open front windows
 Turn ignition switch OFF
 Pull out Intelligent Key from key slot.
NO. Function Operation condition Symptom Diagnostic ItemReference
page
1INTELLIGENT
KEY SYSTEM/
DOOR LOCK
FUNCTIONLock/unlock door with door re-
quest switch.
(Intelligent Key is in the inside
key antenna detection area)Door does not lock/unlock —DLK-158
2POWER DIS-
TRIBUTION
FUNCTIONPress push-button ignition
switch under the following con-
ditions.
 Selector lever position is in
the P or N position
 Do not depress brake pedalPush-button ignition switch
does not operate—PCS-124
3INTELLIGENT
KEY SYSTEM/
ENGINE START
FUNCTIONStart engine with Intelligent Key
into the vehicle (Intelligent Key
is in the inside key antenna de-
tection area)Engine can not start with Intel-
ligent Key—SEC-193
4Open the door after the ignition
switch is turned ON to OFFSteering is not locked —SEC-194
5
NISSAN VEHI-
CLE IMMOBI-
LIZER
SYSTEM-NATS
FUNCTIONStart engine with Intelligent Key
in the key slotEngine can not start —SEC-195
6Open the door after the ignition
switch is turned ON to OFFSteering is not locked —SEC-194
7Insert Intelligent Key in the key
slotKey slot indicator does not illu-
minate—SEC-196

PWC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION PWC
A
B
PWC
N
O
P
CONTENTS
POWER WINDOW CONTROL SYSTEM
BASIC INSPECTION ....................................4
DIAGNOSIS AND REPAIR WORKFLOW ..........4
WorkFlow ..................................................................4
INSPECTION AND ADJUSTMENT .....................5
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL .....................................
5
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description ......
5
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement .......................................................
5
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ..........................................................
5
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................
5
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......
6
FUNCTION DIAGNOSIS ...............................7
POWER WINDOW SYSTEM ...............................7
System Diagram .......................................................7
System Description ...................................................7
Component Parts Location ......................................8
Component Description .............................................8
DIAGNOSIS SYSTEM (BCM) ............................10
COMMON ITEM .........................................................10
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .....................................................
10
RETAINED PWR .......................................................11
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) ...................................................
11
COMPONENT DIAGNOSIS .........................12
POWER SUPPLY AND GROUND CIRCUIT ......12
BCM ...........................................................................12
BCM : Diagnosis Procedure ....................................12
POWER WINDOW MAIN SWITCH ............................12
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure ................................................................
12
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) .................................................................
13
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) : Diagnosis Procedure ..........................
13
REAR POWER WINDOW SWITCH ...........................14
REAR POWER WINDOW SWITCH : Diagnosis
Procedure ................................................................
14
FRONT POWER WINDOW SWITCH (PAS-
SENGER SIDE) .................................................
16
Description ...............................................................16
Component Function Check ....................................16
Diagnosis Procedure ...............................................16
Component Inspection .............................................17
REAR POWER WINDOW SWITCH ..................18
Description ...............................................................18
Component Function Check ....................................18
Diagnosis Procedure ...............................................18
Component Inspection .............................................19
POWER WINDOW MOTOR ..............................20
DRIVER SIDE .............................................................20
DRIVER SIDE : Description .....................................20
DRIVER SIDE : Component Function Check ..........20
DRIVER SIDE : Diagnosis Procedure .....................20
DRIVER SIDE : Component Inspection ...................21
PASSENGER SIDE ....................................................21
PASSENGER SIDE : Description ............................21
PASSENGER SIDE : Component Function Check
....
21
PASSENGER SIDE : Diagnosis Procedure ............21
PASSENGER SIDE : Component Inspection ..........22

PWC-10
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)INFOID:0000000003825997
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
NOTE:
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD) AND IGN COUNTER
Freeze Frame Data
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support MonitorMonitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
Configuration Read and save the vehicle specification.
 Write the vehicle specification when replacing BCM.
System Sub system selection itemDiagnosis mode
Work Support Data Monitor Active Test
Door lock DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Interior room lamp timer INT LAMP×××
Exterior lamp HEAD LAMP×××
Wiper and washer WIPER××
Turn signal and hazard warning lamps FLASHER×××
— AIR CONDITONER*
 Intelligent Key system
 Engine start systemINTELLIGENT KEY×××
Combination switch COMB SW×
Body control system BCM×
IVIS - NATS IMMU××
Interior room lamp battery saver BATTERY SAVER×××
Back door open TRUNK××
Vehicle security system THEFT ALM×××
— RETAINED PWR*×
Signal buffer system SIGNAL BUFFER××
— TPMS (AIR PRESSURE MONITOR)*×××

RF-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION RF
A
B
RF
N
O
P
CONTENTS
ROOF
BASIC INSPECTION ....................................3
DIAGNOSIS AND REPAIR WORKFLOW ..........3
WorkFlow ..................................................................3
INSPECTION AND ADJUSTMENT .....................4
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ..........................................................
4
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................
4
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......
4
FUNCTION DIAGNOSIS ...............................5
SUNROOF SYSTEM ...........................................5
System Diagram .......................................................5
System Description ...................................................5
Component Parts Location ......................................8
Component Description ............................................8
DIAGNOSIS SYSTEM (BCM) .............................9
COMMON ITEM ...........................................................9
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .......................................................
9
RETAINED PWR .......................................................10
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) ...................................................
10
COMPONENT DIAGNOSIS .........................11
POWER SUPPLY AND GROUND CIRCUIT ......11
BCM ...........................................................................11
BCM : Diagnosis Procedure ....................................11
SUNROOF MOTOR ASSEMBLY ..............................11
SUNROOF MOTOR ASSEMBLY :
Diagnosis Procedure ..............................................
11
SUNSHADE MOTOR ASSEMBLY ............................12
SUNSHADE MOTOR ASSEMBLY :
Diagnosis Procedure ..............................................
12
COMMUNICATION SIGNAL CIRCUIT .............14
Description ...............................................................14
Diagnosis Procedure ...............................................14
SUNROOF SWITCH ..........................................15
Description ...............................................................15
Component Function Check ....................................15
Diagnosis Procedure ..............................................15
Component Inspection .............................................16
DOOR SWITCH .................................................18
Description ...............................................................18
Component Function Check ..................................18
Diagnosis Procedure ...............................................18
Component Inspection .............................................19
ECU DIAGNOSIS .........................................20
BCM (BODY CONTROL MODULE) .................20
Reference Value ......................................................20
Wiring Diagram - BCM - ..........................................43
Fail-safe ...................................................................49
DTC Inspection Priority Chart ...............................51
DTC Index ...............................................................52
SUNROOF MOTOR ASSEMBLY .....................54
Reference Value ......................................................54
Wiring Diagram - SUNROOF CONTROL SYS-
TEM - .......................................................................
56
SUNSHADE MOTOR ASSEMBLY ...................60
Reference Value ......................................................60
Wiring Diagram - SUNROOF CONTROL SYS-
TEM - .......................................................................
61
SYMPTOM DIAGNOSIS ..............................65
SUNROOF DOES NOT OPERATE PROPER-
LY ......................................................................
65

DIAGNOSIS SYSTEM (BCM)
RF-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)INFOID:0000000003812848
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
NOTE:
 *1:At model with Intelligent Key system this item is displayed, but is not used.
 *2: This item is displayed, but is not used. Diagnosis mode Function Description
Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support MonitorMonitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
Configuration Read and save the vehicle specification.
 Write the vehicle specification when replacing BCM.
System Sub system selection itemDiagnosis mode
Work Support Data Monitor Active Test
Door lock DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Interior room lamp timer INT LAMP×××
Remote keyless entry system
MULTI REMOTE ENT*
1×××
Exterior lamp HEAD LAMP×××
Wiper and washer WIPER××
Turn signal and hazard warning lamps FLASHER×××
—
AIR CONDITONER*
2
 Intelligent Key system
 Engine start systemINTELLIGENT KEY×××
Combination switch COMB SW×
Body control system BCM×
NVIS - NATS IMMU××
Interior room lamp battery saver BATTERY SAVER×××
Back door opener system TRUNK××
Vehicle security system THEFT ALM×××
RAP system RETAINED PWR×
Signal buffer system SIGNAL BUFFER××
TPMS TPMS (AIR PRESSURE MONITOR)×××

SEC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G H
I
J
L
M
SECTION SEC
A
B
SEC
N
O P
CONTENTS
SECURITY CONTROL SYSTEM
INTELLIGENT KEY SYSTEM
BASIC INSPECTION ....... .............................
5
DIAGNOSIS AND REPAIR WORKFLOW ..... .....5
Work Flow ........................................................... ......5
INSPECTION AND ADJUSTMENT .....................8
ECM RE-COMMUNICATING FUNCTION ............. ......8
ECM RE-COMMUNICATING FUNCTION : De-
scription .....................................................................
8
ECM RE-COMMUNICATING FUNCTION : Spe-
cial Repair Requirement ............................................
8
FUNCTION DIAGNOSIS ...............................9
INTELLIGENT KEY SYSTEM/ENGINE
START FUNCTIO N ........................................ .....
9
System Diagram .................................................. ......9
System Description ...................................................9
Component Parts Location ......................................12
Component Description ...........................................13
NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS ..................................................................
14
System Diagram .................................................. ....14
System Description .................................................14
Component Parts Location ......................................15
Component Description ..........................................16
VEHICLE SECURITY SYSTEM .........................17
System Diagram .................................................. ....17
System Description .................................................17
Component Parts Location ......................................18
Component Description ...........................................19
DIAGNOSIS SYSTEM (BCM) ............................21
COMMON ITEM ..................................................... ....21
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .....................................................
21
INTELLIGENT KEY ................................................ ....22
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ....................................
22
THEFT ALM ........................................................... ....25
THEFT ALM : CONSULT-III Function (BCM -
THEFT) ................................................................ ....
25
IMMU ...................................................................... ....27
IMMU : CONSULT-III Function (BCM - IMMU) ........27
COMPONENT DIAGNOSIS .........................28
U1000 CAN COMM CIRCUIT ...........................28
BCM ....................................................................... ....28
BCM : Description ....................................................28
BCM : DTC Logic .....................................................28
BCM : Diagnosis Procedure ....................................28
IPDM E/R ................................................................ ....28
IPDM E/R : Description ............................................28
IPDM E/R : DTC Logic .............................................28
IPDM E/R : Diagnosis Procedure ............................28
U1010 CONTROL UNIT (CAN) .........................30
BCM ....................................................................... ....30
BCM : DTC Logic .....................................................30
BCM : Diagnosis Procedure ....................................30
BCM : Special Repair Requirement .........................30
P1610 LOCK MODE .........................................31
Description ...............................................................31
DTC Logic ................................................................31
Diagnosis Procedure ...............................................31
P1611 ID DISCORD, IMMU-ECM .....................32
Description ...............................................................32
DTC Logic ................................................................32
Diagnosis Procedure ...............................................32
P1612 CHAIN OF ECM-IMMU ..........................34

SEC-4
Description .............................................................117
Component Function Check ................................117
Diagnosis Procedure .............................................117
HORN FUNCTION ...........................................118
Description .............................................................118
Component Function Check ................................118
Diagnosis Procedure ............................................118
HAZARD FUNCTION .......................................120
Description .............................................................120
Component Function Check ................................120
Diagnosis Procedure .............................................120
INTELLIGENT KEY SYSTEM/ENGINE
START FUNCTION ..........................................
121
Wiring Diagram - INTELLIGENT KEY SYSTEM/
ENGINE START FUNCTION - ..............................
121
NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS ................................................................
129
Wiring Diagram - NVIS - ........................................129
VEHICLE SECURITY SYSTEM .......................137
Wiring Diagram - VEHICLE SECURITY SYSTEM
- .............................................................................
137
ECU DIAGNOSIS .......................................144
BCM (BODY CONTROL MODULE) ................144
Reference Value ....................................................144
Wiring Diagram - BCM - ........................................167
Fail-safe .................................................................173
DTC Inspection Priority Chart .............................175
DTC Index .............................................................176
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ...............
178
Reference Value ....................................................178
Wiring Diagram - IPDM E/R - .................................186
Fail-safe .................................................................189
DTC Index .............................................................191
SYMPTOM DIAGNOSIS ............................192
SECURITY CONTROL SYSTEM .....................192
Symptom Table .....................................................192
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSIDE OF VEHICLE ...............
193
Description .............................................................193
Diagnosis Procedure .............................................193
STEERING DOES NOT LOCK ........................194
Description .............................................................194
Diagnosis Procedure .............................................194
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSERTED INTO KEY SLOT ...
195
Description ............................................................195
Diagnosis Procedure .............................................195
SECURITY INDICATOR LAMP DOES NOT
TURN ON OR FLASH ......................................
196
Description ............................................................196
Diagnosis Procedure .............................................196
VEHICLE SECURITY SYSTEM CAN NOT BE
SET ...................................................................
197
INTELLIGENT KEY .................................................197
INTELLIGENT KEY : Description ..........................197
INTELLIGENT KEY : Diagnosis Procedure ..........197
DOOR REQUEST SWITCH .....................................197
DOOR REQUEST SWITCH : Description .............197
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
197
VEHICLE SECURITY ALARM DOES NOT
ACTIVATE ........................................................
199
Description ............................................................199
Diagnosis Procedure .............................................199
VEHICLE SECURITY SYSTEM CAN NOT BE
CANCELED ......................................................
200
INTELLIGENT KEY .................................................200
INTELLIGENT KEY : Description ..........................200
INTELLIGENT KEY : Diagnosis Procedure ..........200
DOOR REQUEST SWITCH .....................................200
DOOR REQUEST SWITCH : Description .............200
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
200
KEY SLOT INDICATOR DOES NOT ILLUMI-
NATE ................................................................
201
Description ............................................................201
Diagnosis Procedure .............................................201
PRECAUTION ...........................................202
PRECAUTIONS ................................................202
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
202
Precaution for Procedure without Cowl Top Cover .202
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
202
ON-VEHICLE REPAIR ..............................204
KEY SLOT ........................................................204
Removal and Installation .......................................204
PUSH BUTTON IGNITION SWITCH ................205
Removal and Installation .......................................205

SEC-12
< FUNCTION DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Component Parts Location
INFOID:0000000003814904
1. BCM M118, M119, M121, M122, M123 2. TCM F23 3. IPDM E/R E10, E11, F12
4. ECM E16 5. Push-button ignition switch M101 6. Key slot M99
7. Combination meter (key warning lamp)
M348. Combination meter (security indicator
lamp) M349. Horn (high) E340, E341
10. Horn (low) E342, E343 11. Control device (detention switch) M57 12. Stop lamp switch E115
13. Remote keyless entry receiver M78
A. Behind the combination meter B. Engine room (LH) C. View with the center console as-
sembly removed
D. Behind the instrument lower panel LH E. Behind the instrument lower panel RH
JMKIA2349ZZ

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
SEC-13
< FUNCTION DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
Component DescriptionINFOID:0000000003814905
1. Inside key antenna (instrument cen-
ter) M1052. Inside key antenna (console) M262 3. Inside key antenna (trunk room) B86
4. Trunk lid lock assembly (trunk room
lamp switch) T55. Front door switch (driver side) B34 6. Power window main switch (door
lock and unlock switch) D5, D6
A. Behind the cluster lid C assembly B. Trunk room
JMKIA2350ZZ
Component Reference
BCMSEC-91
Steering lock unitSEC-78
Push-button ignition switchSEC-92
Door switchDLK-57
Control device (detention switch)SEC-56
Inside key antennaDLK-50
Remote keyless entry receiverDLK-67
Stop lamp switchSEC-50
Park/neutral position switchSEC-64
Steering lock relaySEC-69
Starter relaySEC-72
Starter control relaySEC-102
Security indicator lampSEC-115
Key warning lampSEC-117