warning NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 4235 of 5121

SIDE AIR BAG (SATELLITE) SENSOR
SR-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
Never impact he side air bag (satellite) sensor.
Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact.
Replace the side air bag (satellite) sensor of deployed SRS front side air bag and deployed SRS side
curtain air bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never use old fixing nuts after removal; replace with new nuts.
In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
JMHIA0009ZZ
Page 4236 of 5121

SR-22
< ON-VEHICLE REPAIR >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded ViewINFOID:0000000003838677
Removal and InstallationINFOID:0000000003838678
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
Before disconnecting the diagnosis sensor unit harness connector, be sure to disconnect each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
Never use air tools or electric tools for servicing.
REMOVAL
1. Disconnect each connector of all air bag modules and pre-tensioner seat belts.
2. Remove the center console assembly. Refer to IP-22, "
Removal and Installation".
3. Remove the rear ventilator duct. Refer to VTL-53, "
REAR VENTILATOR DUCT 1 : Exploded View".
1. Bracket 2. Diagnosis sensor unit
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA0628GB
Page 4237 of 5121

DIAGNOSIS SENSOR UNIT
SR-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
4. Disconnect diagnosis sensor unit (1) harness connectors (A).
5. Remove harness clip (B).
6. Remove fixing bolts (C), and then remove diagnosis sensor unit.
CAUTION:
Never impact the diagnosis sensor unit.
Replace the diagnosis sensor unit if it has been dropped or
sustained an impact.
Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never use old fixing bolts after removal; replace with new fixing bolts.
In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to SRC-10, "
Diagnosis Description".
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the
vehicle as equipped.
JMHIA0629ZZ
JMHIA0009ZZ
SpecificationECU DISCRIMINATED
No.
VQ25DE Driver and passenger air bag, front seat belt pre-tensioner and
front side air bag AE07
Driver and passenger air bag, front seat belt pre-tensioner, front
side air bag and side curtain air bag
AE09
VQ35DEDriver and passenger air bag, front seat belt pre-tensioner, front
side air bag and side curtain air bag
Page 4244 of 5121

SRC-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION SRC
A
B
SRC
N
O
P
CONTENTS
SRS AIRBAG CONTROL SYSTEM
BASIC INSPECTION ....................................5
DIAGNOSIS AND REPAIR WORK FLOW .........5
Work Flow .................................................................5
FUNCTION DIAGNOSIS ...............................7
SRS AIR BAG SYSTEM ......................................7
System Diagram ........................................................7
System Description ...................................................7
Component Parts Location ........................................8
Component Description .............................................8
DIAGNOSIS SYSTEM (AIRBAG) ......................10
Diagnosis Description .............................................10
Air Bag Warning Lamp Diagnosis ...........................10
CONSULT-III Function ............................................15
COMPONENT DIAGNOSIS .........................16
B1001, B1002, B1003, B1004, B1005 DIAG-
NOSIS SENSOR UNIT .......................................
16
Description ..............................................................16
DTC Logic ...............................................................16
Diagnosis Procedure ...............................................16
B1006, B1007, B1008, B1009, B1010 DIAG-
NOSIS SENSOR UNIT .......................................
18
Description ..............................................................18
DTC Logic ...............................................................18
Diagnosis Procedure ...............................................18
B1011, B1012, B1013, B1014, B1015 DIAG-
NOSIS SENSOR UNIT .......................................
20
Description ..............................................................20
DTC Logic ...............................................................20
Diagnosis Procedure ...............................................20
B1026, B1027, B1028, B1029, B1030, B1031
DIAGNOSIS SENSOR UNIT ..............................
22
Description ..............................................................22
DTC Logic ...............................................................22
Diagnosis Procedure ...............................................22
B1033, B1034 CRASH ZONE SEN ..................24
Description ...............................................................24
DTC Logic ................................................................24
Diagnosis Procedure ...............................................24
B1035, B1036 CRASH ZONE SEN ..................26
Description ...............................................................26
DTC Logic ................................................................26
Diagnosis Procedure ...............................................26
B1037, B1039, B1041 CRASH ZONE SENS1 ...28
Description ...............................................................28
DTC Logic ................................................................28
Diagnosis Procedure ...............................................28
B1042, B1043, B1044, B1045, B1046, B1047
DIAGNOSIS SENSOR UNIT .............................
30
Description ...............................................................30
DTC Logic ................................................................30
Diagnosis Procedure ...............................................30
B1049 DRIVER AIRBAG MODULE ..................32
Description ...............................................................32
DTC Logic ................................................................32
Diagnosis Procedure ...............................................32
B1050 DRIVER AIRBAG MODULE ..................34
Description ...............................................................34
DTC Logic ................................................................34
Diagnosis Procedure ...............................................34
B1051 DRIVER AIRBAG MODULE ..................36
Description ...............................................................36
DTC Logic ................................................................36
Diagnosis Procedure ...............................................36
B1052 DRIVER AIRBAG MODULE ..................38
Description ...............................................................38
DTC Logic ................................................................38
Diagnosis Procedure ...............................................38
Page 4247 of 5121

SRC-4
SRS AIR BAG WARNING LAMP DOES NOT
TURN OFF .......................................................
145
Diagnosis Procedure .............................................145
SRS AIR BAG WARNING LAMP DOES NOT
TURN ON .........................................................
146
Diagnosis Procedure .............................................146
PRECAUTION ...........................................147
PRECAUTIONS ................................................147
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
147
Service ..................................................................147
Page 4249 of 5121

SRC-6
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
3.PERFORM SELF-DIAGNOSIS USING “CONSULT-III” (WITH CONSULT-III)
Perform “AIR BAG” Self Diagnostic Result.
Is
“MALFUNCTIONING PART” displayed on CONSULT-III?
YES >> GO TO 5.
NO >> Repeat DTC confirmation with diagnostic procedure.
4.PERFORM SELF-DIAGNOSIS “AIR BAG” WARNING LAMP (WITHOUT CONSULT-III)
Check the air bag warning lamp status.
Is
“MALFUNCTIONING PART” detected?
YES >> GO TO 5.
NO >> Repeat DTC confirmation with diagnostic procedure.
5.REPAIR OR REPLACE
Repair or replace the malfunctioning part.
After the malfunction is repaired, erase the self-diagnostic result. Refer to SRC-10, "
Air Bag Warning Lamp
Diagnosis" or SRC-15, "CONSULT-III Function".
>> GO TO 6.
6.FINAL CHECK
Perform “AIR BAG” Self Diagnostic Result with CONSULT-III and /or, air bag warning lamp status.
Are all malfunctions corrected?
YES >>INSPECTION END
NO-1 >> GO TO 3. (With CONSULT-III)
NO-2 >> GO TO 4. (Without CONSULT-III)
Page 4250 of 5121

SRS AIR BAG SYSTEM
SRC-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
FUNCTION DIAGNOSIS
SRS AIR BAG SYSTEM
System DiagramINFOID:0000000003813930
System DescriptionINFOID:0000000003813931
THIS SRS AIR BAG SYSTEM HAS THE FOLLOWING FUNCTIONS
1. Detects crash and supply the energy for deploying air bag and seat belt pre-tensioner.
2. Detects electrical trouble in air bag system and seat belt pre-tensioner system, records trouble code, and
blinking air bag warning lamp.
JMHIA0600GB
Page 4251 of 5121

SRC-8
< FUNCTION DIAGNOSIS >
SRS AIR BAG SYSTEM
3. Detects and records the deployment of air bag and seat belt pre-tensioner, and turns on air bag warning
lamp.
4. Indicates malfunctioning portion with blinking times of air bag warning lamp in diagnosis mode.
5. Indicates the malfunctioning record by CONSULT-III.
Component Parts LocationINFOID:0000000003813932
Component DescriptionINFOID:0000000003813933
Air bag diagnosis sensor units are prepared for operation while the ignition switch is in the ON or START
position.
The operation of Supplemental Restraint System is different from collision modes application. For example,
the driver air bag module and front passenger air bag module are activated in a frontal collision but not in a
side collision.
SRS configurations which are activated for some collision modes are as follows.
1. Front passenger air bag module M62 2. Driver air bag module M350 3. Conbination switch (Spiral cable)
M32
4. Air bag diagnosis sensor unit B14,
B228, M595. LH/RH satellite sensor
LH B37
RH B2116. Front LH/RH seat belt pre-tensioner
LH B36
RH B213
7. Front LH/RH side air bag module
LH B16
RH B2128. Crash zone sensor E313 9. Combination meter (Air bag warning
lamp) M34
10. LH/RH side curtain air bag module
LH B72
RH B256
JMHIA0599ZZ
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module. Refer to SRC-122, "
Diagnosis
Procedure"×——
Front passenger air bag module. Refer to SRC-122,
"Diagnosis Procedure"×——
Page 4253 of 5121

SRC-10
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (AIRBAG)
DIAGNOSIS SYSTEM (AIRBAG)
Diagnosis DescriptionINFOID:0000000003813934
CAUTION:
• Never use electrical test equipment on any circuit related to the SRS unless instructed in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Never repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a
new one.
Keep ground portion clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using air bag warning lamp and/or CONSULT-III.
The user mode is exclusively prepared for the customer (driver). This mode warns the driver of a system
malfunction through the operation of the air bag warning lamp.
The diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the air bag warning lamp and CONSULT-III are as follows.
HOW TO PERFORM TROUBLE DIAGNOSIS FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information from Customer.
WHAT..... Vehicle model.
WHEN..... Date, Frequency.
WHERE..... Road conditions.
HOW..... Operating conditions, Symptoms.
Preliminary Check.
Check that the following parts are in good order.
Battery (Refer to PG-3, "
How to Handle Battery").
Fuse (Refer to PG-82, "
Fuse").
System component-to-harness connections.
Air Bag Warning Lamp DiagnosisINFOID:0000000003843289
SELF-DIAGNOSIS FUNCTION
The reading of these results is accomplished by “User mode” and “Diagnosis mode”.
After a malfunction is repaired, turn ignition switch ON. Diagnosis mode returns to the User mode. At that
time, the self-diagnosis result is cleared.
User mode Diagnosis mode Display type
Air bag warning lamp X X ON-OFF operation
CONSULT-III – X Monitoring
Page 4254 of 5121

DIAGNOSIS SYSTEM (AIRBAG)
SRC-11
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P HOW TO CHANGE SELF-DIAGNOSIS MODE WITHOUT CONSULT-III
DIAGNOSTIC PROCEDURE (USER MODE)
Checking air bag operation according to air bag warning lamp-User mode
1. Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
2. Compare the air bag warning lamp blinking pattern with the
examples.
PHIA0709E
BF-1845D