mirror NISSAN TEANA 2008 Workshop Manual

INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-87
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003774578
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom Possible cause Inspection item
All the following lamps are not turned ON.
Map lamp
Personal lamp
 Trunk room lamp
Step lamp
 Vanity mirror lamp Harness between BCM and each
interior room lamp
BCMInterior room lamp power supply cir-
cuit
Refer to INL-20
.
 Interior room lamp is not
turned ON even though
the door is open.
(It turns ON when turning
the interior room lamp
ON.)
 Interior room lamp does
not turn OFF even though
the door is closed.Map lamp and personal
lamp Harness between BCM and each
door switch
 Harness between BCM and map
lamp
BCMDoor switch circuit
Refer to DLK-57
.
Interior room lamp control circuit
Refer to INL-22
.
Only the map lamp Map lamp bulb
 Map lamp assembly—
Only the personal lamp Personal lamp bulb
 Personal lamp assembly—
Interior room lamp timer does not activate.
(It turns ON/OFF when the door opens/closes.)—Check the interior room lamp setting.
Refer to INL-16
.
Step lamps (driver side and passenger side) are not
turned ON.
(Map lamp and personal lamp are turned ON.) Harness between BCM and each
step lamp
BCMStep lamp circuit
Refer to INL-24
.
Step lamps (driver side and passenger side) are not
turned OFF.
(Map lamp and personal lamp are turned OFF.)
 Trunk room lamp does not turn ON.
(The bulb is normal.)
 Trunk room lamp does not turn OFF. Harness between BCM and trunk
room lamp switch
 Harness between BCM and trunk
room lamp
BCMTrunk room lamp switch circuit
Refer toDLK-70
.
Trunk room lamp circuit
Refer to INL-26
.
Push-button ignition switch illumination does not illu-
minate. Harness between BCM and push-
button ignition switch
BCMPush-button ignition switch illumina-
tion circuit
Refer to INL-28
.
Interior room lamp battery saver does not activate. —Check the interior room lamp battery
saver setting.
Refer to INL-17
.

INL-92
< ON-VEHICLE REPAIR >
VANITY MIRROR LAMP
VANITY MIRROR LAMP
Exploded ViewINFOID:0000000003774587
ReplacementINFOID:0000000003774588
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
VANITY MIRROR LAMP BULB
1. Insert any appropriate tool into the gap between the lens. Remove the lens.
2. Remove the bulb.
1. Bulb 2. Lens
JPLIA1107ZZ

INL-98
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb SpecificationsINFOID:0000000003774604
Item Type Wattage (W)
Push-button ignition switch illumination LED —
Map lamp Wedge 8
Mood lampMap lamp
LED — Front door grip
Rear door grip
Vanity mirror lamp — 2
Ashtray illumination Wedge 1.4
Glove box lamp Wedge 1.4
Ste p l am p We dg e 2. 7
Personal lamp Wedge 8
Trunk room lamp Wedge 3.4

INT-30
< ON-VEHICLE REPAIR >
FRONT DOOR FINISHER
ON-VEHICLE REPAIR
FRONT DOOR FINISHER
DRIVER SIDE
DRIVER SIDE : Exploded ViewINFOID:0000000003819216
DRIVER SIDE : Removal and InstallationINFOID:0000000003819217
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1. Front door panel 2. Front door inside handle 3. Power window switch finisher
4. Front door finisher 5. Inside handle escutcheon 6. Step lamp
7. Cap 8. Seat memory switch finisher 9. Power window switch
10. Door mirror remote control switch
: Clip
: Pawl
: Metal clip
JMJIA1798ZZ

INT-50
< ON-VEHICLE REPAIR >
HEADLINING
NORMAL ROOF : Removal and Installation
INFOID:0000000003819229
REMOVAL
1. Remove front body side welt (LH/RH) and front pillar garnish (LH/RH). Refer to INT-39, "Removal and
Installation".
2. Disconnect the roof harness (1) connector (B), antenna feeder (2) harness connector (C) and then
remove the clips (A) as shown in the figure below.
3. Remove sun visor assembly (LH/RH).
 Remove sun visor cover.
 Remove sun visor assembly (1) mounting screws (B) with a
screwdriver (A).
 Disconnect vanity mirror lamp harness connector.
4. Rotate 90 degrees and remove sun visor holder (1) (LH/RH).
16. Map lamp lens RH 17. Map lamp lens LH 18. Assist grip clip
19. Personal lamp bracket 20. Personal lamp bulb 21. Personal lamp cover
22. Personal lamp lens
: Pawl
: Metal clip
: Clip
JMJIA1785ZZ
JMJIA1786ZZ
JMJIA1787ZZ

INT-54
< ON-VEHICLE REPAIR >
HEADLINING
SUNROOF : Removal and Installation
INFOID:0000000003826878
REMOVAL
1. Remove front body side welt (LH/RH) and front pillar garnish (LH/RH). Refer to INT-39, "Removal and
Installation".
2. Disconnect the roof harness (1) connector (B), antenna feeder (2) harness connector (C) and then
remove all the clips (A) as shown in the figure below.
3. Remove sun visor assembly (LH/RH).
 Remove sun visor cover.
 Remove sun visor assembly (1) mounting screws (B) with a
screwdriver (A).
 Disconnect vanity mirror lamp harness connectors.
4. Rotate 90 degrees and remove sun visor holder (1) (LH/RH).
: Pawl
: Metal clip
: Clip
JMJIA1785ZZ
JMJIA1786ZZ
JMJIA1787ZZ

MIR-1
DRIVER CONTROLS
C
DE
F
G H
I
J
K
M
SECTION MIR
A
B
MIR
N
O P
CONTENTS
MIRRORS
FUNCTION DIAGNOSIS .. .............................2
DOOR MIRROR SYSTEM .............................. .....2
Component Description ....................................... ......2
COMPONENT DIAGNOSIS ..........................3
DOOR MIRROR .............................................. .....3
Wiring Diagram - DOOR MIRROR SYSTEM - .... ......3
SYMPTOM DIAGNOSIS ...............................6
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ........................ ........................................
6
Work Flow ........................................................... ......6
Inspection Procedure ................................................8
Diagnostic Worksheet .............................................10
PRECAUTION ..............................................12
PRECAUTIONS .............................................. ....12
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
12
PREPARATION ...........................................13
PREPARATION .............................................. ....13
Commercial Service Tools ................................. ....13
ON-VEHICLE REPAIR .................................14
INSIDE MIRROR ...............................................14
Exploded View ..................................................... ....14
Removal and Installation .........................................14
OUTSIDE MIRROR ...........................................15
DOOR MIRROR ASSEMBLY ....................................15
DOOR MIRROR ASSEMBLY : Exploded View ... ....15
DOOR MIRROR ASSEMBLY : Removal and In-
stallation ..................................................................
15
DOOR MIRROR ASSEMBLY : Disassembly and
Assembly .................................................................
15
GLASS MIRROR .................................................... ....17
GLASS MIRROR : Exploded View ..........................18
GLASS MIRROR : Disassembly and Assembly .. ....18
DOOR MIRROR COVER ....................................... ....19
DOOR MIRROR COVER : Exploded View ..............19
DOOR MIRROR COVER : Disassembly and As-
sembly .....................................................................
19
DOOR MIRROR REMOTE CONTROL
SWITCH .............................................................
21
Exploded View .........................................................21
Removal and Installation .........................................21

MIR-2
< FUNCTION DIAGNOSIS >
DOOR MIRROR SYSTEM
FUNCTION DIAGNOSIS
DOOR MIRROR SYSTEM
Component DescriptionINFOID:0000000003815733
Component Function
Door mirror remote control switchIt supplies power to mirror motor through mirror switch and changeover
switch.
Door mirrorIt makes mirror face operate from side to side and up and down with the
mirror control switch operation.

DOOR MIRROR
MIR-3
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
COMPONENT DIAGNOSIS
DOOR MIRROR
Wiring Diagram - DOOR MIRROR SYSTEM -INFOID:0000000003815736
JCLWM1434GB

MIR-4
< COMPONENT DIAGNOSIS >
DOOR MIRROR
JCLWM1435GB