mirror NISSAN TEANA 2008 Owner's Manual

EM-48
< ON-VEHICLE REPAIR >
FUEL INJECTOR AND FUEL TUBE
c. Align center to insert quick connector straightly into fuel tube.
 Insert quick connector (1) to fuel tube until top spool (2) is
completely inside quick connector, and 2nd level spool (3)
exposes right below quick connector.
CAUTION:
 Hold (A) position as shown in the figure when inserting
fuel tube into quick connector.
 Carefully align center to avoid inclined insertion to pre-
vent damage to O-ring inside quick connector.
 Insert until you hear a “click” sound and actually feel the engagement.
 To avoid misidentification of engagement with a similar sound, be sure to perform the next step.
d. Pull quick connector by hand holding (A) position. Check it is
completely engaged (connected) so that it does not come out
from fuel tube (2).
e. Install quick connector cap (3) to quick connector.
 Install quick connector cap with arrow on surface facing in
direction of quick connector (fuel feed hose side).
CAUTION:
If quick connector cap cannot be installed smoothly, quick
connector may have not been installed correctly. Check connection again.
f. Secure fuel feed hose to clamp of quick connector cap.
8. Install in the reverse order of removal after this step.
InspectionINFOID:0000000003802266
INSPECTION AFTER INSTALLATION
Check on Fuel Leakage
1. Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there
are no fuel leakage at connection points.
NOTE:
Use mirrors for checking at points out of clear sight.
2. Start the engine. With engine speed increased, check again that there are no fuel leakage at connection
points.
CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.
B : Fitted condition
: Upright insertion
1 : Fuel feed hose
B : Upper view
JPBIA0275ZZ
JPBIA0039ZZ

EXL-66
< COMPONENT DIAGNOSIS >[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
DescriptionINFOID:0000000003773570
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function CheckINFOID:0000000003773571
1.CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamp is turned ON.
Is the turn signal lamp turned ON?
YES >> Turn signal lamp circuit is normal.
NO >> Refer to EXL-66, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003773572
1.CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 2.
NO >> Replace the bulb.
2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector, the door mirror connector or the rear combination lamp
connector.
3. Turn the ignition switch ON.
4. With operating the turn signal switch, check the voltage between the BCM harness connector and the
ground.LH : Turn signal lamps (LH) ON
RH : Turn signal lamps (RH) ON
Off : Turn signal lamps OFF

TURN SIGNAL LAMP CIRCUIT
EXL-67
< COMPONENT DIAGNOSIS >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between the BCM harness connector and the front combination lamp, the door mirror or
the rear combination lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Te r m i n a l s
Condition
Voltage (Approx.) (+) (−)
BCM
GroundTurn signal
switch
Connector Terminal
Front/side RH
M11917
LH or RH
Front/side LH 18
OFF 0 V
Rear RH
M12020
LH or RH
Rear LH 25
OFF 0 V
PKID0926E
PKID0926E
BCM Front combination lamp
Continuity
Connector Terminal Connector Terminal
RH
M11917 E319 2
Existed
LH 18 E318 2
BCM Door mirror
Continuity
Connector Terminal Connector Terminal
RH
M11917 D43 2
Existed
LH 18 D3 2
BCM Rear combination lamp
Continuity
Connector Terminal Connector Terminal
RH
M12020 B59 1
Existed
LH 25 B80 1

EXL-68
< COMPONENT DIAGNOSIS >[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
Check continuity between the BCM harness connector and the ground.
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 5.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between the front combination lamp, the door mirror or the rear combination lamp and the
ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES >> Replace the front combination lamp, door mirror assembly or the rear combination lamp.
NO >> Repair the harnesses or connectors.
BCM
GroundContinuity
Connector Terminal
Front/side RH
M11917
Not existed Front/side LH 18
Rear RH
M12020
Rear LH 25
Front combination lamp
GroundContinuity
Connector Terminal
RH E319 4
Existed
LH E318 4
Door mirror
GroundContinuity
Connector Terminal
RH D43 10
Existed
LH D3 10
Rear combination lamp
GroundContinuity
Connector Terminal
RH B59 5
Existed
LH B80 5

EXL-188
< ON-VEHICLE REPAIR >[XENON TYPE]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded ViewINFOID:0000000003816250
Removal and InstallationINFOID:0000000003816251
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove the door mirror glass. Refer to MIR-18, "GLASS MIRROR : Exploded View".
2. Remove the door mirror outer cover. Refer to MIR-19, "
DOOR MIRROR COVER : Exploded View".
3. Remove the door mirror actuator mounting screws (A) and (B).
And then remove the side turn signal lamp mounting screw (C).
4. Remove the door mirror under cover. Refer to MIR-19, "
DOOR MIRROR COVER : Exploded View".
5. Remove the screws (A) and connector (1). And then remove the
side turn signal lamp (2).
INSTALLATION
1. Side turn signal lamp 2. Door mirror under cover
JPLIA1094ZZ
JPLIA1095ZZ
JPLIA1096ZZ

SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-197
< SERVICE DATA AND SPECIFICATIONS (SDS) [XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb SpecificationsINFOID:0000000003774382
Item Type Wattage (W)
Front combination lampHeadlamp (HI) H9 65
Headlamp (LO) D2R 35
Parking Lamp W5W 5
Front turn signal WY21W (Amber) 21
Front fog lamp H11 55
Front side turn signal lamp (integrated into the door mirror) LED —
Rear combination lampStop/tail lamp LED —
Rear turn signal lamp S25 (Amber) 21
Back-up lamp W16W 16
License plate lamp W5W 5
High-mounted stop lamp LED —
Rear fog lamp W21W 21

TURN SIGNAL LAMP CIRCUIT
EXL-235
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
TURN SIGNAL LAMP CIRCUIT
DescriptionINFOID:0000000003894323
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function CheckINFOID:0000000003894324
1.CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamp is turned ON.
Is the turn signal lamp turned ON?
YES >> Turn signal lamp circuit is normal.
NO >> Refer to EXL-235, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003894325
1.CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 2.
NO >> Replace the bulb.
2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector, the door mirror connector or the rear combination lamp
connector.
3. Turn the ignition switch ON.
4. With operating the turn signal switch, check the voltage between the BCM harness connector and the
ground.LH : Turn signal lamps (LH) ON
RH : Turn signal lamps (RH) ON
Off : Turn signal lamps OFF

EXL-236
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-78, "
Exploded View".
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between the BCM harness connector and the front combination lamp, the door mirror or
the rear combination lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Te r m i n a l s
Condition
Voltage (Approx.) (+) (−)
BCM
GroundTurn signal
switch
Connector Terminal
Front/side RH
M11917
LH or RH
Front/side LH 18
OFF 0 V
Rear RH
M12020
LH or RH
Rear LH 25
OFF 0 V
PKID0926E
PKID0926E
BCM Front combination lamp
Continuity
Connector Terminal Connector Terminal
RH
M11917 E319 2
Existed
LH 18 E318 2
BCM Door mirror
Continuity
Connector Terminal Connector Terminal
RH
M11917 D43 2
Existed
LH 18 D3 2
BCM Rear combination lamp
Continuity
Connector Terminal Connector Terminal
RH
M12020 B59 1
Existed
LH 25 B80 1

TURN SIGNAL LAMP CIRCUIT
EXL-237
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Check continuity between the BCM harness connector and the ground.
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 5.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between the front combination lamp, the door mirror or the rear combination lamp and the
ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES >> Replace the front combination lamp, door mirror assembly or the rear combination lamp.
NO >> Repair the harnesses or connectors.
BCM
GroundContinuity
Connector Terminal
Front/side RH
M11917
Not existed Front/side LH 18
Rear RH
M12020
Rear LH 25
Front combination lamp
GroundContinuity
Connector Terminal
RH E319 4
Existed
LH E318 4
Door mirror
GroundContinuity
Connector Terminal
RH D43 10
Existed
LH D3 10
Rear combination lamp
GroundContinuity
Connector Terminal
RH B59 5
Existed
LH B80 5

EXL-352
< ON-VEHICLE REPAIR >[HALOGEN TYPE]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded ViewINFOID:0000000003894369
Removal and InstallationINFOID:0000000003894370
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove the door mirror glass. Refer to MIR-18, "GLASS MIRROR : Exploded View".
2. Remove the door mirror outer cover. Refer to MIR-19, "
DOOR MIRROR COVER : Exploded View".
3. Remove the door mirror actuator mounting screws (A) and (B).
And then remove the side turn signal lamp mounting screw (C).
4. Remove the door mirror under cover. Refer to MIR-19, "
DOOR MIRROR COVER : Exploded View".
5. Remove the screws (A) and connector (1). And then remove the
side turn signal lamp (2).
INSTALLATION
1. Side turn signal lamp 2. Door mirror under cover
JPLIA1094ZZ
JPLIA1095ZZ
JPLIA1096ZZ