NISSAN TEANA 2008 Workshop Manual
TEANA 2008
NISSAN
NISSAN
https://www.carmanualsonline.info/img/5/57391/w960_57391-0.png
NISSAN TEANA 2008 Workshop Manual
Page 3238 of 5121
DOOR MIRROR
MIR-5
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
JCLWM1436GB
Page 3247 of 5121
MIR-14
< ON-VEHICLE REPAIR >
INSIDE MIRROR
ON-VEHICLE REPAIR
INSIDE MIRROR
Exploded ViewINFOID:0000000003815743
Removal and InstallationINFOID:0000000003815744
REMOVAL
1. Insert flat-headed screwdriver (A) under the inside mirror (1).
2. Slide the inside mirror to the upper side while pushing the pawl
downward.
CAUTION:
Never use excessive force to remove the inside mirror because
it is inserted tightly into the mirror base.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be careful to push the pawl until it connects to
the mirror base.
1. Inside mirror 2. Mirror base
Refer to GI-4, "
Components" for symbols in the figure.
JMLIA0145ZZ
JMLIA0055ZZ
Page 3248 of 5121

OUTSIDE MIRROR
MIR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded ViewINFOID:0000000003815745
DOOR MIRROR ASSEMBLY : Removal and InstallationINFOID:0000000003815746
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove clips and remove corner cover.
3. Disconnect door mirror harness connector.
4. Remove door mirror mounting nuts, and remove door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
DOOR MIRROR ASSEMBLY : Disassembly and AssemblyINFOID:0000000003815747
DISASSEMBLY
1. Remove door mirror assembly. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".
2. Remove glass mirror. Refer to MIR-18, "
GLASS MIRROR : Disassembly and Assembly".
3. Remove door mirror cover. Refer to MIR-19, "
DOOR MIRROR COVER : Disassembly and Assembly".
1. Door mirror cover 2. Side turn signal lamp assembly 3. Corner cover
4. Glass mirror 5. Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
Page 3249 of 5121
MIR-16
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
4. Remove screws (A) and connectors, and then remove actuator
(1).
5. Using a flat-bladed screwdriver (A) and remove lower cover (1).
6. Remove TORX bolts (A) and remove base assembly (1).
7. Remove TORX bolts (A) and remove base bracket (1).
JMLIA0160ZZ
JMLIA0161ZZ
JMLIA0162ZZ
JMLIA0163ZZ
Page 3250 of 5121
OUTSIDE MIRROR
MIR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
8. Using a flat-bladed screwdriver (A) and remove bracket cover
(1).
9. Disconnect connector of side turn signal lamp assembly.
10. Remove screws (A) and remove bracket assembly (1).
11. Remove screws (A) and remove under body (1).
12. Remove screws (A) and remove side turn signal lamp assembly
(1).
ASSEMBLY
Assemble in the reverse order of disassembly.
GLASS MIRROR
JMLIA0164ZZ
JMLIA0165ZZ
JMLIA0166ZZ
JMLIA0167ZZ
Page 3251 of 5121

MIR-18
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000003815765
GLASS MIRROR : Disassembly and AssemblyINFOID:0000000003815749
DISASSEMBLY
1. Place the glass mirror upward.
2. Put a strip of protective tape (B) on housing assembly.
3. As shown in the figure, insert a small flat-bladed screwdriver (A)
between glass mirror (1) and actuator (2). Push up both pawls
simultaneously to remove glass mirror lower half side.
NOTE:
Insert screwdriver, and push up while rotating (twisting) to make
work easier.
4. Remove two terminals of mirror heater attachment.
5. Lightly lift up lower side of glass mirror, and detach both pawls of upper side as if pulling it out. Disassem-
ble glass mirror from actuator.
NOTE:
Be careful not to allow grease on sealing agent in center of mirror or back side of glass mirror.
ASSEMBLY
Assemble in the reverse order of disassembly.
1. Door mirror cover 2. Side turn signal lamp assembly 3. Corner cover
4. Glass mirror 5. Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0158ZZ
Page 3252 of 5121
OUTSIDE MIRROR
MIR-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
DOOR MIRROR COVER : Exploded ViewINFOID:0000000003815766
DOOR MIRROR COVER : Disassembly and AssemblyINFOID:0000000003815751
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1. Remove the glass mirror. Refer to MIR-18, "GLASS MIRROR : Disassembly and Assembly".
2. Remove the pawls, and disassemble the door mirror cover from
the mirror assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
1. Door mirror cover 2. Side turn signal lamp assembly 3. Corner cover
4. Glass mirror 5. Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0159ZZ
Page 3253 of 5121
MIR-20
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
CAUTION:
After installation, visually check that pawls are securely engaged.
Page 3254 of 5121
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded ViewINFOID:0000000003815752
Refer to INT-30, "DRIVER SIDE : Exploded View".
Removal and InstallationINFOID:0000000003815753
REMOVAL
1. Remove the power window main switch finisher. Refer to PWC-85, "Exploded View".
2. Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using screwdriver (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0130ZZ