Ioni NISSAN TEANA 2008 Manual Online
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 187 of 5121
![NISSAN TEANA 2008 Manual Online AV
ANTENNA AMP.
AV-43
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA AMP.
Exploded ViewINFOID:0000000003765623
Removal and InstallationINFOID:0000000003765624
REMOVAL
1. Remo NISSAN TEANA 2008 Manual Online AV
ANTENNA AMP.
AV-43
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA AMP.
Exploded ViewINFOID:0000000003765623
Removal and InstallationINFOID:0000000003765624
REMOVAL
1. Remo](/img/5/57391/w960_57391-186.png)
AV
ANTENNA AMP.
AV-43
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA AMP.
Exploded ViewINFOID:0000000003765623
Removal and InstallationINFOID:0000000003765624
REMOVAL
1. Remove rear side pillar finisher. Refer to INT-39, "Removal and Installation".
2. Disconnect antenna feeder connector and clip.
3. Remove antenna amp. mounting nut, disconnect the antenna amp. connector.
4. Remove antenna amp.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1032ZZ
1. AM-FM main connector
2. Antenna amp.
Page 190 of 5121
![NISSAN TEANA 2008 Manual Online AV-46
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
1. Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to AV-68, "CONSULT-III Func-
tion NISSAN TEANA 2008 Manual Online AV-46
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
1. Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to AV-68, "CONSULT-III Func-
tion](/img/5/57391/w960_57391-189.png)
AV-46
< BASIC INSPECTION >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
1. Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to AV-68, "CONSULT-III Func-
tion (MULTI AV)".
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2. Check if any DTC is displayed in the self-diagnosis results.
Is DTC displayed?
YES >> GO TO 3.
NO >> GO TO 4.
3.TROUBLE DIAGNOSIS FOR DTC
1. Check the DTC indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC Index. Refer to AV-126, "
DTC Index".
>> GO TO 5.
4.TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to AV-164, "
Symptom
Table".
>> GO TO 5.
5.ERROR PART REPAIR
1. Repair or replace the identified malfunctioning parts.
2. Perform a self-diagnosis for “MULTI AV” with CONSULT-III.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3. Check that the symptom does not occur.
Does the symptom occur?
YES >> GO TO 1.
NO >> INSPECTION END
Page 192 of 5121
![NISSAN TEANA 2008 Manual Online AV-48
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System DiagramINFOID:0000000003882699
NOTE:
The name MULTIFUNCTION SWITCH indicates the NISSAN TEANA 2008 Manual Online AV-48
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System DiagramINFOID:0000000003882699
NOTE:
The name MULTIFUNCTION SWITCH indicates the](/img/5/57391/w960_57391-191.png)
AV-48
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System DiagramINFOID:0000000003882699
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
A radio antenna base integrated with radio antenna amp. is adopted.
Woofer illustrated in the above figure, integrates two woofers and a woofer amp.
System DescriptionINFOID:0000000003882700
Multi AV system means that the following systems are integrated.
AV control unit controls by transmitting/receiving data one by one with each unit (slave unit) that configures
them completely as a master unit by connecting between units that configure MULTI AV system with two AV
communication lines (H, L).
Two AV communication lines (H, L) adopt a twisted pair line that is resistant to noise.
AV control unit is connected by CAN communication, and it receives data signal from ECM, combination
meter. It computes and displays fuel economy information value with the obtained information. Transmitting/
receiving of data signal is performed by BCM. Also, it transmits the required signal of vehicle setting and
receives the response signal.
JSNIA1431GB
System name System explanation
AUDIO SYSTEMAV- 5 3 , "
System Diagram"
REAR VIEW MONITOR SYSTEMAV- 5 6 , "System Description"
VEHICLE INFORMATION SYSTEM Status of audio, climate control system, fuel economy, mainte-
nance and navigation is displayed.
AV control unit displays the fuel consumption status while re-
ceiving data signal through CAN communication from ECM and
combination meter.
AV control unit is connected to BCM via CAN communication
transmitting/receiving for the vehicle settings function.
AUXILIARY INPUT SYSTEM Refer to “AUXILIARY INPUT SYSTEM” shown below.
Page 195 of 5121
![NISSAN TEANA 2008 Manual Online AV
MULTI AV SYSTEM
AV-51
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003882702
Part name Description
AV CONTROL UNIT It is th NISSAN TEANA 2008 Manual Online AV
MULTI AV SYSTEM
AV-51
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003882702
Part name Description
AV CONTROL UNIT It is th](/img/5/57391/w960_57391-194.png)
AV
MULTI AV SYSTEM
AV-51
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003882702
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
AV control unit includes audio function and vehicle information function.
It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
AUX image signal is input from auxiliary jacks.
Camera image signal is input from camera control unit.
Composite image (AUX and camera images) signal is output to display unit.
AUX sound signal is input from the auxiliary jacks.
Power (signal VCC and inverter VCC) is transmitted to front display unit.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
It receives the power (signal VCC and inverter VCC) from the AV control unit
and operates.
RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
Composite image (AUX and camera images) signal is input from AV control
unit.
Synchronize signal (HP, VP) is output to AV control unit.
FRONT SPEAKER Outputs sound signal from front speaker.
Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from rear speaker.
Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from front squawker.
Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Operation panel is equipped with the centralized switch where camera, audio
and auxiliary input operations are integrated.
The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Operation panel is equipped with the centralized switch where audio and air
conditioner operations are integrated.
The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
The disk ejection operating signal is performed by wiring harness.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
Power supply is transmitted to rear view camera.
AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
It receives the power supply from the camera control unit and operates.
STEERING ANGLE SENSOR Sensor signal (steering angle) is transmitted to camera control unit.
STEERING SWITCH The operations of audio, etc. can be performed.
Steering switch signal (operation signal) is output to AV control unit.
AUXILIARY INPUT JACKS The image signal of the auxiliary input is output via the AV control unit to the
display unit.
The sound signal of the auxiliary input is output via the AV control unit to the
each speaker.
Page 197 of 5121
![NISSAN TEANA 2008 Manual Online AV
AUDIO SYSTEM
AV-53
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUDIO SYSTEM
System DiagramINFOID:0000000003882703
NOTE:
The name MULTIFUNCTION SWITCH indicate NISSAN TEANA 2008 Manual Online AV
AUDIO SYSTEM
AV-53
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUDIO SYSTEM
System DiagramINFOID:0000000003882703
NOTE:
The name MULTIFUNCTION SWITCH indicate](/img/5/57391/w960_57391-196.png)
AV
AUDIO SYSTEM
AV-53
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUDIO SYSTEM
System DiagramINFOID:0000000003882703
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
System DescriptionINFOID:0000000003882704
The audio system is equipped with following function. Each function can be operated with the multifunction
switch, preset switch, rear control switch or steering switch. It indicates the operation status of AUDIO to the
display unit.
FUNCTION DESCRIPTION
Operating Signal
Operation of the audio system can be performed via the multifunction switch, preset switch, rear control switch
or steering switch.
Operating signal is transmitted to AV control unit via AV communication when it is operated by multifunction
switch, preset switch or rear control switch. The CD ejection operating signal is performed by hard-wire.
Operating signal is transmitted to AV control unit with steering switch signal when it is operated by steering
switch.
Screen Display
The display switching of the screen is performed by the communication signal between the display unit and
the AV control unit.
The image signal to display operating condition is performed by RGB image signal, RGB area signal and
RGB image synchronizing signal.
AM/FM Radio Mode
AM/FM radio tuner is built into AV control unit.
AM/FM radio wave is received by glass antenna, next it is amplified by antenna amp., and finally it is input to
AV control unit. The FM sub antenna is installed on the rear window glass and the AV control unit is
received.
Sound signal is input to AV control unit, and AV control unit outputs to each speaker.
CD Mode
CD function is built into AV control unit.
AV control unit outputs sound signal to each speaker when CD is inserted to AV control unit.
JSNIA1434GB
Function
AM/FM radio
CD
Page 199 of 5121
![NISSAN TEANA 2008 Manual Online AV
AUDIO SYSTEM
AV-55
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791248
Part name Description
AV CONTROL UNIT The AM/FM r NISSAN TEANA 2008 Manual Online AV
AUDIO SYSTEM
AV-55
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791248
Part name Description
AV CONTROL UNIT The AM/FM r](/img/5/57391/w960_57391-198.png)
AV
AUDIO SYSTEM
AV-55
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791248
Part name Description
AV CONTROL UNIT The AM/FM receiving function and the CD playing function are equipped.
Sound signal is transmitted to each speaker.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
RGB image signal (audio operation condition) is input from AV control unit.
FRONT SPEAKER Outputs sound signal from front speaker.
Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from rear speaker.
Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from front squawker.
Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Each audio operation can be operated.
The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Each audio operation can be operated.
The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
The disk ejection operating signal is performed by hard-wire.
STEERING SWITCH Each audio operation can be operated.
Steering switch signal (operation signal) is output to AV control unit.
REAR CONTROL SWITCH Each audio operation can be operated.
The rear control switch is connected via AV communication, and it transmits
the operation signals of the rear control switch.
ANTENNA AMP. Radio signal received by glass antenna is amplified and transmitted to AV con-
trol unit.
Power (antenna amp. ON signal) is supplied from AV control unit.
Page 200 of 5121
![NISSAN TEANA 2008 Manual Online AV-56
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW MONITOR SYSTEM
REAR VIEW MONITOR SYSTEM
System DiagramINFOID:0000000003882707
System DescriptionINFOID:0000000003882708
CAMERA IMA NISSAN TEANA 2008 Manual Online AV-56
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW MONITOR SYSTEM
REAR VIEW MONITOR SYSTEM
System DiagramINFOID:0000000003882707
System DescriptionINFOID:0000000003882708
CAMERA IMA](/img/5/57391/w960_57391-199.png)
AV-56
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW MONITOR SYSTEM
REAR VIEW MONITOR SYSTEM
System DiagramINFOID:0000000003882707
System DescriptionINFOID:0000000003882708
CAMERA IMAGE OPERATION PRINCIPLE
Power is supplied to rear view camera from camera control unit and the rear view camera outputs the cam-
era image to camera control unit when selector lever is set to reverse position and the reverse signal on
camera control unit is input.
Camera control unit superimposes the guiding line and predicted course line to the image from rear view
camera and outputs to display unit. In this case, the reverse signal is also input to AV control unit. Therefore,
AV control unit recognizes the selector lever as in the reverse position. And then AV control unit switches the
image displayed by the communication signal between AV control unit and display unit with the camera
image.
AV control unit outputs camera image signal that is inputted from camera control unit to display unit.
Camera control unit controls the direction and distance of predicted course line according to the sensor sig-
nal from steering angle sensor.
AV control unit determines whether rear view camera is equipped or not, based on the presence of camera
connection recognition signal. It switches to rear view monitor image at the time of reverse signal input when
rear view camera is equipped.
Rear view monitor guiding line
JSNIA1379GB
JSNIA1325GB
Page 203 of 5121
![NISSAN TEANA 2008 Manual Online AV
REAR VIEW MONITOR SYSTEM
AV-59
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885184
Part name Description
AV CONTROL UNIT NISSAN TEANA 2008 Manual Online AV
REAR VIEW MONITOR SYSTEM
AV-59
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885184
Part name Description
AV CONTROL UNIT](/img/5/57391/w960_57391-202.png)
AV
REAR VIEW MONITOR SYSTEM
AV-59
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885184
Part name Description
AV CONTROL UNIT Image on display is transmitted to rear view monitor image by serial communi-
cation between AV control unit and display unit.
AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
DISPLAY UNIT Camera image signal is input from AV control unit.
Rear view monitor image is changed by serial communication from AV control
unit.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal is
output to AV control unit.
Power supply is transmitted to rear view camera.
Superimposes the guiding line and predicted course line to the camera image
that outputs to AV control unit.
Inputs the sensor signal from steering angle sensor, and then controls the pre-
dicted course line.
Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
It receives power supply from camera control unit and operates.
STEERING ANGLE SENSORSteering signal necessary for predicted course line control is transmitted to cam-
era control unit.
Page 204 of 5121
![NISSAN TEANA 2008 Manual Online AV-60
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003882711
MULTIFUNCTION SWITCH AND NISSAN TEANA 2008 Manual Online AV-60
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003882711
MULTIFUNCTION SWITCH AND](/img/5/57391/w960_57391-203.png)
AV-60
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003882711
MULTIFUNCTION SWITCH AND PRESET SWITCH SELF-DIAGNOSIS FUNCTION
The ON/OFF operation (continuity) of each switch in the multifunction switch and preset switch can be
checked.
Self-diagnosis Mode
Press the “BACK” switch and the “UP” switch of the 4-direction
switches within 10 seconds after turning the ignition switch from
OFF to ACC and hold them for 3 seconds or more. Then the
buzzer sounds, all indicators of the preset switch illuminate, and
the self-diagnosis mode starts.
The continuity of each switch at the ON position can be checked
by pressing the switch. The buzzer sounds if the switch is normal.
NOTE:
The hazard switch and disk eject switch cannot be checked.
Finishing Self-diagnosis Mode
Self-diagnosis mode is canceled when turning the ignition switch OFF.
MULTI AV SYSTEM ON BOARD DIAGNOSIS FUNCTION
The AV control unit diagnosis function starts up with multifunction switch operation and the AV control unit
performs a diagnosis for each unit in the system during the on board diagnosis.
Perform a CONSULT-III diagnosis if the on board diagnosis does not start, e.g., the screen does not display
anything, the multifunction switch does not function, etc.
ON BOARD DIAGNOSIS
Description
The trouble diagnosis function has a self-diagnosis mode for conducting trouble diagnosis automatically and
a confirmation/adjustment mode for operating manually.
Self-diagnosis mode performs the AV control unit diagnosis and the connection diagnosis between each of
the units that make up the system, and it indicates the results to the display.
The confirmation/adjustment mode allows the technician to check, modify or adjust the vehicle signals and
set values, as well as to monitor the system error records and system communication status. The check,
modify or adjust actions generally require human intervention and judgment (the system cannot make judg-
ment automatically).
On Board Diagnosis Item
JSNIA1284GB
Mode Description
Self Diagnosis AV control unit diagnosis.
Diagnoses the connections across system components.
Page 205 of 5121
![NISSAN TEANA 2008 Manual Online AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-61
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
*:On-board self-diagnosis is not supported. Only CONSULT-III is sup NISSAN TEANA 2008 Manual Online AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-61
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
*:On-board self-diagnosis is not supported. Only CONSULT-III is sup](/img/5/57391/w960_57391-204.png)
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-61
< FUNCTION DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
*:On-board self-diagnosis is not supported. Only CONSULT-III is supported.
STARTING PROCEDURE
1. Start the engine.
2. Turn the audio system OFF.
3. While pressing the “SETTING” button, turn the volume control
dial clockwise or counterclockwise for 40 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
Shifting from current screen to previous screen is performed
by pressing “BACK” button.
4. The trouble diagnosis initial screen is displayed, and then the
items of “Self Diagnosis” and “Confirmation/Adjustment” can be
selected.
SELF-DIAGNOSIS MODE
1. Start the self-diagnosis function and select “Self Diagnosis”.
- Self-diagnosis subdivision screen is displayed, and the self-diagnosis mode starts.
- The bar graph visible on the center of the self-diagnosis subdivision screen indicates progress of the trou-
ble diagnosis.
Confirmation/
AdjustmentDisplay DiagnosisThe following check functions are available: color tone check by color
bar display, light and shade check by grey scale display and touch panel
calibration response check.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, ignition switch, and reverse.
Speaker Test The connection of a speaker can be confirmed by test tone.
Climate Control
*Not used.
Error HistoryThe system malfunction and the frequency when occurred in the past are
displayed. When the malfunctioning item is selected, the time and place
that the selected malfunction last occurred are displayed.
Camera Cont.It can perform the confirmation of a signal connection to the camera con-
trol unit, the calibration of each camera, Correct Draw Line of Camera
Image, and Fine Tuning of Birds-Eye View.
Refer to AV- 6 0 , "
Diagnosis Description".
Vehicle CAN Diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM DiagnosisThe communication condition of each unit of Multi AV system can be
monitored.
Delete Unit Connection Log Erase the connection history of unit and error history.
Initialize Settings Initializes the AV control unit memory.Mode Description
JSNIA1285GB
JSNIA0138GB