reverse NISSAN TIIDA 2007 Service Repair Manual

EX-6
< ON-VEHICLE REPAIR >[HR16DE]
EXHAUST SYSTEM
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Always replace exhaust gaskets and seal bearings with new ones when installing.
 Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
 Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner and apply anti-seize lubricant (commercial service tool).
 Do not over tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
 Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
 Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
 When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/left
directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown.
 Exhaust front tube (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Install spring (3), tighten nut (4).
 Be careful that the stud bolt nut does not interfere with the
flanged area ( ).
 Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown.
 Center muffler (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring (3), tighten bolt (4).
 Be careful that the stud bolt does not interfere with the flanged
area ( ).
 Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
InspectionINFOID:0000000001700348
INSPECTION AFTER INSTALLATION
 With the engine running, check exhaust tube joints for exhaust leakage and unusual noise.
 Check to ensure that brackets and mounting rubbers are installed properly and free from undue stress.
Improper installation could result in excessive noise and vibration.
PBIC3797E
PBIC3798E

EXHAUST SYSTEM
EX-11
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Always replace exhaust gaskets and seal bearings with new ones when installing.
 Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
 Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner and apply anti-seize lubricant (commercial service tool).
 Do not over tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
 Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
 Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
 When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/left
directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown.
 Exhaust front tube (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Install spring (3), tighten nut (4).
 Be careful that the stud bolt nut does not interfere with the
flanged area ( ).
 Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown.
 Center muffler (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring (3), tighten bolt (4).
 Be careful that the stud bolt does not interfere with the flanged
area ( ).
 Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
INSPECTION AFTER INSTALLATION
 With the engine running, check exhaust tube joints for exhaust leakage and unusual noise.
 Check to ensure that brackets and mounting rubbers are installed properly and free from undue stress.
Improper installation could result in excessive noise and vibration.
InspectionINFOID:0000000001696389
INSPECTION AFTER INSTALLATION
 Make sure clearance between tail tube and rear bumper is even.
 With engine running, check exhaust tube joints for gas leakage and unusual noises.
 Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
PBIC3797E
PBIC3798E

EX-14
< ON-VEHICLE REPAIR >[K9K]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001700347
Removal and InstallationINFOID:0000000001696393
CAUTION:
 Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance and shape.
 Perform the operation with the exhaust system fully cooled down because the system is still hot just
after the engine stops.
 Be careful not to cut your hand on the insulator edge.
REMOVAL
 Disconnect each joint and mounting.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Always replace exhaust gaskets and seal bearings with new ones when installing.
 Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
 Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
1. Main muffler 2. Mounting rubber 3. Ring gasket
4. Center muffler 5. Spring 6. Seal bearing
7. Exhaust front tube 8. Stud bolt 9. Ground cable
AWBIA0159GB

HEADLAMP
EXL-85
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
3. Remove the headlamp bolts (A).
4. Pull the headlamp (1) toward the vehicle front, disconnect the
headlamp connector, and remove the headlamp.
INSTALLATION
Installation is in the reverse order of removal.
 After installation, perform aiming adjustment. Refer to EXL-81, "
Aiming Adjustment".
Disassembly and Assembly - HalogenINFOID:0000000001529254
DISASSEMBLY
1. Remove the back cover.
2. Unlock the retaining spring and remove the halogen bulb.
3. Turn parking (clearance) lamp bulb socket counterclockwise to unlock it.
4. Remove the parking (clearance) lamp bulb from the socket.
5. Turn front turn signal lamp bulb socket counterclockwise to unlock it.
6. Remove the front turn signal lamp bulb from the socket.
7. Remove the bumper stay.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
After installing the halogen bulb, install the plastic cap securely to insure a water tight seal.
PKIC1223E
1. Retaining spring 2. Parking (clearance) lamp bulb 3. Parking (clearance) lamp bulb socket
4. Halogen bulb (High/Low) 5. Back cover 6. Front turn signal lamp bulb socket
7. Front turn signal lamp bulb 8. Headlamp housing assembly
PKIC4642E

EXL-86
< ON-VEHICLE REPAIR >
HEADLAMP
Disassembly and Assembly - Xenon
INFOID:0000000001530430
DISASSEMBLY
1. Turn the plastic cap counterclockwise and remove it.
2. Turn the xenon bulb socket counterclockwise to unlock it.
3. Unlock the retaining spring and remove the xenon bulb (high/low).
4. Remove the mounting screws from the HID control unit.
5. Disconnect the HID control unit connector and remove the screw from the HID control unit.
6. Turn the parking (clearance) lamp bulb socket counter clockwise and remove it.
7. Remove the parking lamp bulb from the socket.
8. Turn the front turn signal lamp bulb socket counterclockwise and remove it.
9. Remove the front turn signal lamp bulb from the socket.
ASSEMBLY
Assembly is the reverse order of disassembly.
CAUTION:
 If the HID control unit is removed, reinstall it securely.
 After installing the Xenon bulb, install the plastic cap and bulb socket securely to insure it is water
tight.
1. Retaining spring 2. Parking (clearance) lamp bulb 3. Parking (clearance) lamp bulb socket
4. Xenon bulb (High/Low) 5. Xenon bulb socket 6. Plastic cap
7. Seal packing 8. Screw 9. Seal packing
10. HID control unit 11. Screw 12. Front turn signal lamp bulb socket
13. Front turns signal lamp bulb 14. Headlamp housing assembly
PKIC0913E

FRONT FOG LAMP
EXL-87
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
FRONT FOG LAMP
Bulb ReplacementINFOID:0000000001529284
1. Turn the lighting switch OFF.
2. Reposition the fender protector (front) out of the way to access the front fog lamp.
3. Disconnect the front fog lamp connector (1).
4. Turn the bulb socket (2) counterclockwise to unlock it.
5. Remove the socket and bulb from the fog lamp.
6. Remove the bulb from the socket.
Removal and InstallationINFOID:0000000001529285
REMOVAL
1. Reposition the fender protector (front) out of the way to access the front fog lamp.
2. Disconnect the front fog lamp connector.
3. Release the pawl and remove the front bumper finisher from the front bumper.
4. Remove front fog lamp bolt and remove the front fog lamp from the front bumper finisher.
INSTALLATION
Installation is in the reverse order of removal.
PKIC1071E
1. Front fog lamp 2. Front bumper finisher 3. Front fog lamp bolt
WKIA5420E

EXL-88
< ON-VEHICLE REPAIR >
HEADLAMP AIMING CONTROL
HEADLAMP AIMING CONTROL
Removal and Installation of Headlamp Aiming SwitchINFOID:0000000001530404
REMOVAL
1. Remove the instrument lower finisher. Refer to IP-11, "Removal and Installation".
2. Spread the switch panel finisher pawls to remove the headlamp aiming switch.
INSTALLATION
Installation is in the reverse order of removal.

EXL-90
< ON-VEHICLE REPAIR >
HEADLAMP AIMING CONTROL
INSTALLATION
Installation is in the reverse order of removal.
 Tighten the height sensor bolt closest to the vehicle front first when installing the height sensor.
 The new height sensor must be initialized using Consult III for proper functioning of the automatic headlamp
aiming system.

AUTO LIGHT SYSTEM
EXL-91
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
AUTO LIGHT SYSTEM
Removal and Installation of Light and Rain SensorINFOID:0000000001530408
REMOVAL
1. Remove the rear view mirror. Refer to MIR-9, "Removal and Installation".
2. Disconnect the light and rain sensor connector.
3. Remove the light and rain sensor.
INSTALLATION
Installation is in the reverse order of removal.

EXL-92
< ON-VEHICLE REPAIR >
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Bulb ReplacementINFOID:0000000001530538
1. Remove the side turn signal lamp. Refer to EXL-92, "Removal and Installation".
2. Turn bulb socket counterclockwise to unlock it.
3. Remove the bulb from the socket.
Removal and InstallationINFOID:0000000001530539
REMOVAL
1. Insert a suitable tool under the side turn signal lamp. While
pushing in on the side turn signal lamp pawl, pull the lamp away
from the front fender as shown.
2. Disconnect the side turn signal lamp connector and remove the
side turn signal lamp.
NOTE:
Secure the side turn signal lamp harness with tape to prevent
the harness from falling into the front fender.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Install the lamp housing with the bead facing up.
PKIB8657E
PKIB8656E