engine control NISSAN TIIDA 2007 Service Repair Manual

STC-22
< ECU DIAGNOSIS >[EPS]
EPS CONTROL UNIT
ECU DIAGNOSIS
EPS CONTROL UNIT
EPS Control Unit Input/Output Signal Reference ValueINFOID:0000000001716757
SPECIFICATIONS WITH CONSULT-III
CAUTION:
The output signal indicates the EPS control unit calculation date. The normal values will be displayed
even in the event that the output circuit (harness) is open.
*1: In the front of the value, “L” is displayed at steering left and “R” is displayed at steering right.
*2: Almost in accordance with the value of “MOTOR SIG”. It is not a malfunction though these values are not accorded when steering
quickly.
*3: It is not a malfunction, though it might not be corresponding just after ignition switch is turned ON.
*4: It turns to OFF after waiting for a short period of time.Monitor item (Unit) Content Condition Display value
MOTOR VOL (V)Power supply voltage for
EPS control unitIgnition switch: ON Battery voltage
TORQUE SENSOR (Nm)Steering wheel turning
forceEngine runningSteering wheel: Not
steering (There is no
steering force) 0.00 Nm
Steering wheel: Steer-
ing0 – 8.19 Nm
*1 (The value
is changed according to
steering left or right)
MOTOR SIG (A)Command current to EPS
motorEngine runningSteering wheel: Not
steering (There is no
steering force)0.00 A
Steering wheel: Steer-
ing0 – 65.00 A (The value is
changed according to
steering left or right)
MOTOR CURRENT (A)Consumption current of
EPS motorEngine runningSteering wheel: Not
steering (There is no
steering force)0.00 A
Steering wheel: Steer-
ing0 – 65.00 A
*2 (The value
is changed according to
steering left or right)
VEHICLE SPEED (km/h) or (mph) Vehicle speedVehicle stopped 0 km/h (0 mph)
While drivingApproximately equal to
the indication on speed-
ometer (Inside of ±10%)
*3
WARNING LAMP (ON/OFF)EPS warning lamp condi-
tionEPS warning lamp: ON ON
EPS warning lamp: OFF OFF
DERATING STAT (ON/OFF) Protect overload status Engine runningSteering wheel: Nor-
mal steeringOFF
Steering wheel: Steer-
ing over the stopON
*4
ENGINE STATUS (RUN/STOP) Engine statusEngine stopped
(Engine speed: Less than 400 rpm)STOP
Engine running
(Engine speed: 400 rpm or more)RUN

EPS CONTROL UNIT
STC-23
< ECU DIAGNOSIS >[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
N
O
P
EPS HARNESS CONNECTOR TERMINAL LAYOUT
TERMINALS AND REFERENCE VALUES FOR EPS CONTROL UNIT
Data are reference values and are measured between each terminal and ground.
CAUTION:
When using a circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.
SGIA1624E
Te r m i n a lWire
colorItem Condition Data (Approx.)
4 V Torque sensor sub Engine runningSteering wheel: Not steering
(There in no steering force)2.5 V
Steering wheel: Steering1.7 V – 3.3 V
(The value is changed accord-
ing to steering left or right)
5 BR Torque sensor power supplyIgnition switch: ON 8 V
Ignition switch: OFF 0 V
6 G Torque sensor main Engine runningSteering wheel: Not steering
(There is no steering force)2.5 V
Steering wheel: Steering1.7 V – 3.3 V
(The value is changed accord-
ing to steering left or right)
7 R Torque sensor ground Always 0 V
9 L CAN-H — —
10 O Power supplyIgnition switch: ON Battery voltage
Ignition switch: OFF 0 V
16 P CAN-L — —
17 R Power supply (Memory back-up)Ignition switch: ON Battery voltage
Ignition switch: OFF Battery voltage
18 B Ground Always 0 V
19 — Motor (+) — —
20 — Motor (–) — —

EPS SYSTEM SYMPTOMS
STC-29
< SYMPTOM DIAGNOSIS >[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
N
O
P
SYMPTOM DIAGNOSIS
EPS SYSTEM SYMPTOMS
Symptom ChartINFOID:0000000001716771
If EPS warning lamp turns ON, perform self-diagnosis. Refer to STC-7, "CONSULT-III Function (EPS)".
Symptom Condition Check item Reference page
EPS warning lamp does not turn ON when ig-
nition switch to “ON”.
(EPS warning lamp check)Ignition switch: ONCAN communication line
STC-30
Combination meter
EPS warning lamp does not turn OFF for sev-
eral seconds after starting the engineEngine runningCAN communication line
STC-31
Power supply and ground for
EPS control unit
Torque sensor
EPS motor
Vehicle speed signal
Engine status signal
Combination meter
Steering wheel turning force is heavy or light,
while driving While driving
 Steering wheel turningCAN communication line
STC-33
Vehicle speed signal
Engine status signal
EPS motor
Steering wheel turning force
(Mechanical malfunction)
Unbalance steering wheel turning force and
return between right and left, while driving While driving
 Steering wheel turningWheel alignment
STC-34
Steering wheel turning force
(Mechanical malfunction)
Unbalance steering wheel turning force,
while driving (Torque variation) While driving
 Steering wheel turningSteering column intermediate
shaft installation condition
STC-35
Steering wheel turning force
(Mechanical malfunction)

EPS WARNING LAMP DOES NOT TURN OFF
STC-31
< SYMPTOM DIAGNOSIS >[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
N
O
P
EPS WARNING LAMP DOES NOT TURN OFF
Diagnosis ProcedureINFOID:0000000001697734
SYMPTOM:
EPS warning lamp does not turn OFF for several seconds after starting the engine.
DIAGNOSTIC PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to STC-7, "
CONSULT-III Function (EPS)".
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 2.
2.CHECK EPS CONTROL UNIT POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect EPS control unit harness connector.
3. Turn ignition switch ON. (Do not start engine.)
4. Check voltage between EPS control unit harness connector
M53 (A) terminal 10 and M54 (B) terminal 17 and ground.
5. Turn ignition switch OFF.
6. Check voltage between EPS control unit harness connector
M53 (A) terminal 10 and M54 (B) terminal 17 and ground.
7. Connect EPS control unit harness connector.
OK or NG
OK >> GO TO 3.
NG >> Check the following. If any items are damaged, repair
or replace damaged parts.
 60 A fusible link (letter m , located in the fuse and fusible link box).
 10 A fuse [No. 2, located in the fuse block (J/B)].
 Harness for short or open between battery and EPS control unit harness connector M54 termi-
nal 17.
 Harness for short or open between ignition switch and EPS control unit harness connector M53
terminal 10.
3.CHECK EPS CONTROL UNIT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect EPS control unit harness connector.
Connector Terminal Voltage
(A) M53 10 – Ground Battery voltage
(B) M54 17 – Ground Battery voltage
AWGIA0031ZZ
Connector Terminal Voltage
(A) M53 10 – Ground Approx. 0 V
(B) M54 17 – Ground Battery voltage
AWGIA0028ZZ

STEERING WHEEL TURNING FORCE IS HEAVY OR LIGHT
STC-33
< SYMPTOM DIAGNOSIS >[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
N
O
P
STEERING WHEEL TURNING FORCE IS HEAVY OR LIGHT
Diagnosis ProcedureINFOID:0000000001697735
SYMPTOM:
Steering wheel turning force is heavy or light, while driving.
DIAGNOSTIC PROCEDURE
1.CHECK SYSTEM FOR CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to STC-7, "
CONSULT-III Function (EPS)".
Is the
“CAN COMM CIRCUIT [U1000]” displayed?
YES >> Perform trouble diagnosis for CAN communication line. Refer to STC-21, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK VEHICLE SPEED SIGNAL
Perform self-diagnosis with ABS actuator and electric unit (control unit). Refer to BRC-25, "
CONSULT-III
Function (ABS)" (with ABS) or BRC-105, "CONSULT-III Function (ABS)" (with ESP).
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 3.
3.CHECK COMBINATION METER SIGNAL
Perform self-diagnosis with combination meter. Refer to MWI-22, "
CONSULT-III Function (METER/M&A)".
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 4.
4.CHECK ENGINE STATUS SIGNAL
Perform self-diagnosis for ECM. Refer to EC-107, "
CONSULT-III Function" (HR16DE with EURO-OBD), EC-
462, "CONSULT-III Function" (HR16DE without EURO-OBD), EC-772, "CONSULT-III Function" (MR18DE),
EC-1104, "
Diagnosis Description" (K9K).
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 5.
5.CHECK EPS MOTOR SYSTEM
Perform trouble diagnosis for EPS motor. Refer to STC-13, "
Diagnosis Procedure".
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
6.CHECK EPS CONTROL UNIT
Check EPS control unit input/output signal. Refer to STC-22, "
EPS Control Unit Input/Output Signal Reference
Va l u e".
OK or NG
OK >> GO TO 7.
NG >> Check EPS control unit pin terminals for damage or loose connection with harness connector. If
any items are damaged, repair or replace damaged parts.
7.SYMPTOM CHECK
Check again.
OK or NG
OK >>INSPECTION END
NG >> Check the steering wheel turning force because there may be mechanical malfunction. Refer to
ST-6, "
On-Vehicle Inspection and Service".

STC-34
< SYMPTOM DIAGNOSIS >[EPS]
UNBALANCE STEERING WHEEL TURNING FORCE AND RETURN BETWEEN
RIGHT AND LEFT
UNBALANCE STEERING WHEEL TURNING FORCE AND RETURN BE-
TWEEN RIGHT AND LEFT
Diagnosis ProcedureINFOID:0000000001697736
SYMPTOM:
Unbalance steering wheel turning force and return between right and left, while driving.
DIAGNOSTIC PROCEDURE
1.CHECK EPS WARNING LAMP
Confirm EPS warning lamp during engine running.
Does EPS warning lamp turn OFF?
YES >> GO TO 2.
NO >> Go to STC-31, "
Diagnosis Procedure".
2.CHECK WHEEL ALIGNMENT
Check wheel alignment. Refer to FSU-6, "
Wheel Alignment Inspection".
OK or NG
OK >> GO TO 3.
NG >> Adjust wheel alignment. Refer to FSU-6, "
Wheel Alignment Inspection".
3.CHECK EPS CONTROL UNIT
Check EPS control unit input/output signal. Refer to STC-22, "
EPS Control Unit Input/Output Signal Reference
Va l u e".
OK or NG
OK >> GO TO 4.
NG >> Check EPS control unit pin terminals for damage or loose connection with harness connector. If
any items are damaged, repair or replace damaged parts.
4.SYMPTOM CHECK
Check again.
OK or NG
OK >>INSPECTION END
NG >> Check the steering wheel turning force because there may be mechanical malfunction. Refer to
ST-6, "
On-Vehicle Inspection and Service".

UNBALANCE STEERING WHEEL TURNING FORCE (TORQUE VARIATION)
STC-35
< SYMPTOM DIAGNOSIS >[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
N
O
P
UNBALANCE STEERING WHEEL TURNING FORCE (TORQUE VARIA-
TION)
Diagnosis ProcedureINFOID:0000000001697737
SYMPTOM:
Unbalance steering wheel turning force, while driving (Torque variation).
DIAGNOSTIC PROCEDURE
1.CHECK EPS WARNING LAMP
Confirm EPS warning lamp during engine running.
Does EPS warning lamp turn OFF?
YES >> GO TO 2.
NO >> Go to STC-31, "
Diagnosis Procedure".
2.CHECK STEERING COLUMN INTERMEDIATE SHAFT
Check the connection between intermediate shaft and the mounting part of steering column assembly and
steering gear assembly. Refer to ST-9, "
Removal and Installation".
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3.CHECK EPS CONTROL UNIT
Check EPS control unit input/output signal. Refer to STC-22, "
EPS Control Unit Input/Output Signal Reference
Va l u e".
OK or NG
OK >> GO TO 4.
NG >> Check EPS control unit pin terminals for damage or loose connection with harness connector. If
any items are damaged, repair or replace damaged parts.
4.SYMPTOM CHECK
Check again.
OK or NG
OK >>INSPECTION END
NG >> Check the steering wheel turning force because there may be mechanical malfunction. Refer to
ST-6, "
On-Vehicle Inspection and Service".

TM-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION TM
A
B
TM
N
O
P
CONTENTS
TRANSAXLE & TRANSMISSION
TYPE 1 (4AT: RE4F03B)
BASIC INSPECTION ...................................
10
DIAGNOSIS AND REPAIR WORKFLOW .........10
Work Flow ...............................................................10
Diagnostic Work Sheet ............................................11
FUNCTION DIAGNOSIS ..............................13
A/T CONTROL SYSTEM ....................................13
Cross-Sectional View ..............................................13
Shift Mechanism ......................................................14
TCM Function ..........................................................21
CAN Communication ...............................................22
Input/Output Signal of TCM .....................................22
Line Pressure Control .............................................23
Shift Control ............................................................24
Lock-up Control .......................................................25
Engine Brake Control (Overrun Clutch Control) ......26
Control Valve ...........................................................28
Centrifugal Cancel Mechanism ...............................28
Component Parts Location ......................................30
A/T SHIFT LOCK SYSTEM ................................31
System Description .................................................31
Component Parts Location ......................................31
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......32
Introduction .............................................................32
OBD Function for A/T System .................................32
One or Two Trip Detection Logic of OBD ................32
OBD Diagnostic Trouble Code (DTC) .....................32
Malfunction Indicator Lamp (MIL) ............................33
DIAGNOSIS SYSTEM (TCM) .............................35
CONSULT-III Function (TRANSMISSION) .............35
Diagnosis Procedure without CONSULT-III ............38
COMPONENT DIAGNOSIS .........................43
DTC U1000 CAN COMMUNICATION LINE .......43
Description ...............................................................43
On Board Diagnosis Logic .......................................43
Possible Cause ........................................................43
DTC Confirmation Procedure ..................................43
Diagnosis Procedure ...............................................43
DTC P0705 PARK/NEUTRAL POSITION
(PNP) SWITCH ..................................................
44
Description ...............................................................44
CONSULT-III Reference Value in Data Monitor
Mode ........................................................................
44
On Board Diagnosis Logic .......................................44
Possible Cause ........................................................44
DTC Confirmation Procedure ..................................44
Diagnosis Procedure ...............................................44
Component Inspection .............................................46
DTC P0710 A/T FLUID TEMPERATURE SEN-
SOR CIRCUIT ...................................................
48
Description ...............................................................48
CONSULT-III Reference Value in Data Monitor
Mode ........................................................................
48
On Board Diagnosis Logic .......................................48
Possible Cause ........................................................48
DTC Confirmation Procedure ..................................48
Diagnosis Procedure ...............................................48
Component Inspection .............................................50
DTC P0720 VEHICLE SPEED SENSOR·A/T
(REVOLUTION SENSOR) .................................
52
Description ...............................................................52
CONSULT-III Reference Value in Data Monitor
Mode ........................................................................
52
On Board Diagnosis Logic .......................................52
Possible Cause ........................................................52
DTC Confirmation Procedure ..................................52
Diagnosis Procedure ...............................................53
DTC P0725 ENGINE SPEED SIGNAL .............56
Description ...............................................................56

TM-3
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
DTC TURBINE REVOLUTION SENSOR .........104
Description ............................................................104
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
104
On Board Diagnosis Logic ....................................104
Possible Cause .....................................................104
DTC Confirmation Procedure ................................104
Diagnosis Procedure .............................................104
CONTROL UNIT (RAM), CONTROL UNIT
(ROM) ...............................................................
108
Description ............................................................108
On Board Diagnosis Logic ....................................108
Possible Cause .....................................................108
DTC Confirmation Procedure ................................108
Diagnosis Procedure .............................................108
MAIN POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................
109
Description ............................................................109
On Board Diagnosis Logic ....................................109
Possible Cause .....................................................109
DTC Confirmation Procedure ................................109
Diagnosis Procedure .............................................109
PNP, OD SWITCH AND CLOSED THROT-
TLE, WIDE OPEN THROTTLE POSITION
SIGNAL CIRCUIT .............................................
111
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
111
TCM Terminal and Reference Value .....................111
Diagnosis Procedure .............................................111
Component Inspection ..........................................115
A/T SHIFT LOCK SYSTEM ..............................116
Wiring Diagram - A/T Shift Lock System - .............116
Terminals And Reference Values .........................116
Diagnosis Procedure .............................................117
ECU DIAGNOSIS .......................................119
TCM ..................................................................119
Reference Value ...................................................119
Wiring Diagram - A/T CONTROL SYSTEM - ........123
Fail-Safe ................................................................123
DTC Inspection Priority Chart ...............................125
DTC Index .............................................................125
DTC Alphabetical Index ........................................126
SYMPTOM DIAGNOSIS ............................127
SYSTEM SYMPTOM ........................................127
Symptom Chart .....................................................127
OD OFF Indicator Lamp Does Not Come On .......138
Engine Cannot Be Started in "P" and "N" Position ..140
In "P" Position, Vehicle Moves Forward or Back-
ward When Pushed ...............................................
140
In "N" Position, Vehicle Moves ..............................141
Large Shock "N" → "R" Position ...........................142
Vehicle Does Not Creep Backward in "R" Position ..142
Vehicle Does Not Creep Forward in "D", "2" or "1"
Position ..................................................................
144
Vehicle Cannot Be Started from D1 .......................145
A/T Does Not Shift: D1→ D2or Does Not Kick-
down: D
4→ D2 .......................................................146
A/T Does Not Shift: D2→ D3 ..................................148
A/T Does Not Shift: D3→ D4 ..................................149
A/T Does Not Perform Lock-up .............................151
A/T Does Not Hold Lock-up Condition ...................151
Lock-up Is Not Released .......................................152
Engine Speed Does Not Return to Idle (Light
Braking D
4→ D3) ...................................................153
A/T Does Not Shift: D4→ D3, When OD OFF ........154
A/T Does Not Shift: D3→ 22, When Selector Lever
"D" → "2" Position .................................................
155
A/T Does Not Shift: 22→ 11, When Selector Lever
"2" → "1" Position ..................................................
156
Vehicle Does Not Decelerate by Engine Brake .....158
TCM Self-Diagnosis Does Not Activate .................161
PRECAUTION ............................................163
PRECAUTIONS ...............................................163
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
163
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect .................................
163
Precaution for On Board Diagnosis (OBD) System
of A/T and Engine (For Type1 Only) ......................
163
Precaution .............................................................164
Service Notice or Precaution .................................165
Wiring Diagram and Trouble Diagnosis .................165
PREPARATION .........................................166
PREPARATION ...............................................166
Special Service Tool ..............................................166
Commercial Service Tool ......................................169
ON-VEHICLE MAINTENANCE ..................171
A/T FLUID .......................................................171
Checking A/T Fluid ................................................171
Changing A/T Fluid ................................................171
A/T Fluid Cooler Cleaning .....................................172
STALL TEST ...................................................175
Inspection and Judgment ......................................175
LINE PRESSURE TEST ..................................178
Inspection and Judgment ......................................178
ROAD TEST ....................................................180
Description .............................................................180
Check Before Engine Is Started ............................180
Check at Idle ..........................................................181
Cruise Test - Part 1 ...............................................183
Cruise Test - Part 2 ...............................................185
Cruise Test - Part 3 ...............................................186
Vehicle Speed When Shifting Gears .....................188

TM-5
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P Cross-Sectional View ............................................
329
Shift Mechanism ....................................................330
TCM Function ........................................................337
CAN Communication .............................................338
Input/Output Signal of TCM ...................................338
Line Pressure Control ...........................................339
Shift Control ..........................................................340
Lock-up Control .....................................................341
Engine Brake Control (Overrun Clutch Control) ....342
Control Valve .........................................................344
Centrifugal Cancel Mechanism .............................344
Component Parts Location ....................................346
A/T SHIFT LOCK SYSTEM ..............................347
System Description ...............................................347
Component Parts Location ....................................347
DIAGNOSIS SYSTEM (TCM) ...........................348
CONSULT-III Function (TRANSMISSION) ...........348
Diagnosis Procedure without CONSULT-III ..........350
COMPONENT DIAGNOSIS .......................355
VEHICLE SPEED SENSOR - A/T (REVOLU-
TION SENSOR) ................................................
355
Description ............................................................355
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
355
On Board Diagnosis Logic ....................................355
Possible Cause .....................................................355
DTC Confirmation Procedure ................................355
Diagnosis Procedure .............................................356
VEHICLE SPEED SENSOR MTR ....................359
Description ............................................................359
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
359
On Board Diagnosis Logic ....................................359
Possible Cause .....................................................359
DTC Confirmation Procedure ................................359
Diagnosis Procedure .............................................359
SHIFT SOLENOID VALVE A ...........................361
Description ............................................................361
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
361
On Board Diagnosis Logic ....................................361
Possible Cause .....................................................361
DTC Confirmation Procedure ................................361
Diagnosis Procedure .............................................361
Component Inspection ..........................................363
SHIFT SOLENOID VALVE B ...........................365
Description ............................................................365
CONSULT-III Reference Value in Data Monitor
Mode .....................................................................
365
On Board Diagnosis Logic ....................................365
Possible Cause .....................................................365
DTC Confirmation Procedure ................................365
Diagnosis Procedure .............................................365
Component Inspection ...........................................367
OVERRUN CLUTCH SOLENOID VALVE ......369
Description .............................................................369
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
369
On Board Diagnosis Logic .....................................369
Possible Cause ......................................................369
DTC Confirmation Procedure ................................369
Diagnosis Procedure .............................................369
Component Inspection ...........................................371
TORQUE CONVERTER CLUTCH SOLENOID
VALVE .............................................................
373
Description .............................................................373
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
373
On Board Diagnosis Logic .....................................373
Possible Cause ......................................................373
DTC Confirmation Procedure ................................373
Diagnosis Procedure .............................................373
Component Inspection ...........................................375
BATT/FLUID TEMP SEN (A/T FLUID TEMP
SENSOR CIRCUIT AND TCM POWER
SOURCE) ........................................................
376
Description .............................................................376
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
376
On Board Diagnosis Logic .....................................376
Possible Cause ......................................................376
DTC Confirmation Procedure ................................376
Diagnosis Procedure .............................................376
Component Inspection ...........................................379
ENGINE SPEED SIGNAL ...............................381
Description .............................................................381
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
381
On Board Diagnosis Logic .....................................381
Possible Cause ......................................................381
DTC Confirmation Procedure ................................381
Diagnosis Procedure .............................................381
TURBINE REVOLUTION SENSOR ................383
Description .............................................................383
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
383
On Board Diagnosis Logic .....................................383
Possible Cause ......................................................383
DTC Confirmation Procedure ................................383
Diagnosis Procedure .............................................383
LINE PRESSURE SOLENOID VALVE ...........387
Description .............................................................387
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
387
On Board Diagnosis Logic .....................................387
Possible Cause ......................................................387
DTC Confirmation Procedure ................................387